I lost power steering while driving due to bad can bus connector cause by poor solder joints.
COMPONENT SPOTLIGHT
Jeep Wrangler electrical problems
2,974 distinct owner reports with an electrical-system component in this snapshot.
Includes the electrical-system component and its detailed subcategories. Related recalls and investigations must also name this component; they are not linked by narrative keyword alone.
Reports by model year
Recall and investigation columns show each year’s full history. A report naming several years can appear in more than one row.
When problems were reported
Mileage at the reported incident
1,114 reports with mileage · 1,860 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What owners actually said
2,974 reportsCar shut down on [XXX] and would not start. Indicated problem with charging system. Vehicle is currently in Cabo San Lucas, BCS, Mexico. Towed car to local Jeep dealer. Car had outstanding recall (ZB7 2021-2023 JL 4XE Loss of Motive Power). Dealer diagnosed issues as a failure of the battery, so that was replaced, along with so…
Read full complaint
Car shut down on [XXX] and would not start. Indicated problem with charging system. Vehicle is currently in Cabo San Lucas, BCS, Mexico. Towed car to local Jeep dealer. Car had outstanding recall (ZB7 2021-2023 JL 4XE Loss of Motive Power). Dealer diagnosed issues as a failure of the battery, so that was replaced, along with software updates to address the recalls. We had to pay over $900 out of pocket for these repairs, and it stayed with the dealer for 3.5 weeks. Two days later the vehicle is again failing with the same issues and will not start. It began with the check engine light coming on, then A/C stopped cooling, then the car only would stay in hybrid mode, and the transmission was revving. After stopping the car and shutting it off it will not restart. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
While driving to an appointment on 11 August 2025 the yellow CEL light came on and the Jeep Wrangler 4xe stopped operating in hybrid mode. A few miles later the Jeep went into limp mode with a red turtle, red wrench, and red battery light. Pulled into the left center turn lane to allow faster traffic to pass and then made a lef…
Read full complaint
While driving to an appointment on 11 August 2025 the yellow CEL light came on and the Jeep Wrangler 4xe stopped operating in hybrid mode. A few miles later the Jeep went into limp mode with a red turtle, red wrench, and red battery light. Pulled into the left center turn lane to allow faster traffic to pass and then made a left turn off of a busy 4-lane highway. I then proceeded down the hill and at the next traffic light I was turning right when the Jeep stopped and the gas engine completely shut down and the Jeep stopped moving halfway through the intersection. Putting the vehicle in park, I attempted to restart the vehicle while it sat in the middle of the intersection but it wouldn’t restart. I then turned on my flashers and exited the vehicle so I could call a tow truck. After the vehicle was towed to the nearest Jeep dealership I learned two days later that the hybrid battery pack had failed and it needed to be replaced. As of 18 September and the vehicle is still at the dealership awaiting authorization from the Jeep engineering team so the technician at the dealership can order a special part!
Sudden loss of power. We experienced a sudden loss of engine power. The vehical is currently at a dealership for repairs. We have been informed this is a known issue and a service bulletin has been issued. We are shocked that we were not notified. We were on I75 and had the traffic not been light it is very possible we w…
Read full complaint
Sudden loss of power. We experienced a sudden loss of engine power. The vehical is currently at a dealership for repairs. We have been informed this is a known issue and a service bulletin has been issued. We are shocked that we were not notified. We were on I75 and had the traffic not been light it is very possible we would not have been able to maneuver out of the way of other vehicals. This is not like a rattle or minor malfunction. The engine suddenly and without warning quit producing power. Adress this now before drivers are killed or injured.
The instrument cluster went out on my 2020 Jeep Wrangler. There is a recall (NHTSA#24V-652) for this issue, however my VIN # is not included in the recall. This is a critical safety issue because the speedometer and warning lights to not work.
2021 Jeep Wrangler Rubicon, VIN [XXX] , Recall P0DAB-00 (Hybrid/EV Cell Balancing Performance Case #[XXX], Jeep corporate case manager Tiona. On 8/11/25, I brought my vehicle to Freeland Jeep, Antioch, TN for a separate issue and requested inspection for the open EV battery recall. The dealership gave a “green flag,” confirming…
Read full complaint
2021 Jeep Wrangler Rubicon, VIN [XXX] , Recall P0DAB-00 (Hybrid/EV Cell Balancing Performance Case #[XXX], Jeep corporate case manager Tiona. On 8/11/25, I brought my vehicle to Freeland Jeep, Antioch, TN for a separate issue and requested inspection for the open EV battery recall. The dealership gave a “green flag,” confirming no recall impact. On [XXX], the check engine light came on and the vehicle drove unsafely. On [XXX], the exact recall issue (P0DAB-00) was diagnosed — the same issue we asked to be inspected. Approval for hybrid battery replacement was granted; part was ordered for 9/3 with repair by 9/5 — repair never occurred. Service advisor Brian Astorga claimed the part “cannot be located.” Calls/emails to service manager David Beasley and case manager Tiona are unanswered. The timing is highly suspicious: the vehicle failed immediately after the “all clear” inspection, suggesting potential negligence or miscommunication. We are now more than 1 month without a vehicle, which is unsafe and unacceptable. AND we even had to argue with Jeep to cover a rental! Requested Action: Require Jeep to complete the recall repair immediately or initiate a full buyback. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
My son was turning out of a parking lot and the car suddenly stopped moving and went into park. He couldn’t shift out of park and was stuck in the middle of a very busy street with cars slamming on their brakes to avoid hitting him. The car had to be towed away.
UNKNOWN The display panel on the instrument cluster has went out. There was an open recall for newer models (2022-2024), but my vehicle's year (2020) was not included. After going through multiple forums, and speaking with many dealerships, this has been an on-going issue with multiple Jeep owners.
I see that there are recalls for the center cluster on the dash for jeeps like mine from 2018 through 2022 or 2024 but mine has is not included in that recall however mine is now out According to our mechanic I have a black screen cannot see if I have gas or if my vehicle is overheating, cannot see any of the warning signals. Pl…
Read full complaint
I see that there are recalls for the center cluster on the dash for jeeps like mine from 2018 through 2022 or 2024 but mine has is not included in that recall however mine is now out According to our mechanic I have a black screen cannot see if I have gas or if my vehicle is overheating, cannot see any of the warning signals. Please advise why my jeep is not included in that recall. Mine is a 2020 jeep wrangler unlimited
This is an unmodified 2025 Jeep Wrangler with less than 3000 miles. While driving between 20 and 30 miles per hour, the vehicle went completely dead in traffic. No power, no lights, no dashboard, no blinkers, no brake lights. It stalled and was stuck in drive. It proceeded to roll a few feet after failing. It would not start as …
Read full complaint
This is an unmodified 2025 Jeep Wrangler with less than 3000 miles. While driving between 20 and 30 miles per hour, the vehicle went completely dead in traffic. No power, no lights, no dashboard, no blinkers, no brake lights. It stalled and was stuck in drive. It proceeded to roll a few feet after failing. It would not start as nothing was functioning. Because there was no power to the vehicle at all, I could not open the tailgate to get tools or a light. I had to climb over the seats. The vehicle failed in traffic while driving and came to an immediate stop in the road. In approximately 50ft I would have been turning left into and intersection. After a few days at the dealer, they recreated the problem. They drove it about a mile and it failed in traffic and needed to be towed to the dealership again. There was no warning or check engine light. Everything just went black/dead. The dealer states "The ground wire under the TIPM/Fuse Panel was loose, causing intermittent short to ground canceling all power to vehicle." The vehicle has only 3000 miles on it, so this was a defect from the factory, as the wire is not even accessible without disassembly of the engine compartment.
Related Official recalls
1225V741000 · Electrical System:propulsion System:traction Battery
Oct 30, 2025
Chrysler (FCA US, LLC) is recalling certain 2020-2025 Jeep Wrangler 4Xe and 2022-2026 Grand Cherokee 4Xe vehicles. The high voltage battery may fail internally and lead to a vehicle fire while parked or driving.
Consequence & remedy
Consequence: A vehicle fire can increase the risk of injury.
Remedy: Owners are advised to park outside and away from structures and not to charge their vehicles until the remedy is completed. Dealers will update the high voltage battery software, and replace the high voltage battery, as necessary, free of charge. Some owner notification letters were mailed beginning December 17, 2025. The remaining owner notification letters will be mailed at a later date. Owners may contact Chrysler customer service at 800-853-1403. Chrysler's number for this recall is 68C. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning November 6, 2025. Vehicles that were previously recalled for the same issue under NHTSA Recalls 24V720 and 23V787 will need to have the new remedy performed.
24V871000 · Electrical System:wiring; Exterior Lighting
Nov 19, 2024
Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wrangler vehicles. The incorrect dash wiring harness was installed, which can result in inoperative trailer lighting. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: Trailer lights that fail to illuminate can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the dash wiring harness as necessary, free of charge. Owner notification letters were mailed December 19, 2024. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is B9B.
Additional source detail variants (2)
Exterior Lighting
Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wrangler vehicles. The incorrect dash wiring harness was installed, which can result in inoperative trailer lighting. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: Trailer lights that fail to illuminate can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the dash wiring harness as necessary, free of charge. Owner notification letters were mailed December 19, 2024. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is B9B.
Electrical System:wiring
Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wrangler vehicles. The incorrect dash wiring harness was installed, which can result in inoperative trailer lighting. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: Trailer lights that fail to illuminate can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the dash wiring harness as necessary, free of charge. Owner notification letters were mailed December 19, 2024. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is B9B.
24V652000 · Electrical System: Instrument Cluster/panel
Sep 5, 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
Consequence & remedy
Consequence: An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Remedy: Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
23V787000 · Electrical System:propulsion System:traction Battery
Nov 22, 2023
Chrysler (FCA US, LLC) is recalling certain 2021-2023 Jeep Wrangler Plug-In Hybrid Electric (PHEV) vehicles. The high voltage battery may fail internally and lead to a vehicle fire while parked or driving.
Consequence & remedy
Consequence: A vehicle fire while parked or driving can increase the risk of injury.
Remedy: Owners are advised not to recharge their vehicles, and to park outside and away from structures, until they are repaired. Dealers will update the high voltage battery pack software and replace the battery pack assembly if necessary, free of charge. Owner notification letters were mailed March 7, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 89A. This recall is superseded by NHTSA Recall 24V-720.
23V303000 · Electrical System:propulsion System:traction Battery
Apr 27, 2023
Chrysler (FCA US, LLC) is recalling certain 2022-2023 Jeep Wrangler Plug-In Hybrid Electric vehicles (PHEV). The high voltage (HV) battery pack assembly was built with incorrect fasteners to secure the 200-amp fuse, which can generate excessive heat.
Consequence & remedy
Consequence: Excessive heat may cause the fuse to fail and result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the HV battery fuse, as necessary. Dealers will also inspect the battery assembly for damage and replace it, if necessary. Repairs will be performed free of charge. Owner notification letters were mailed May 23, 2023. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is 53A. This recall is an expansion of previous recall 22V-768.
22V768000 · Electrical System:propulsion System:traction Battery
Oct 13, 2022
Chrysler (FCA US, LLC) is recalling certain 2022-2023 Jeep Wrangler Plug-In Hybrid Electric (PHEV) vehicles. The high voltage (HV) battery pack assembly was built with incorrect fasteners to secure the 200-amp fuse, which can generate excessive heat.
Consequence & remedy
Consequence: Excessive heat may cause the fuse to fail and result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the HV battery fuse, as necessary. Dealers will also inspect the battery assembly for damage and replace it, if necessary. Repairs will be performed free of charge. Owner notification letters were mailed December 8, 2022. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is Z71.
18V524000 · Electrical System:wiring:front Underhood
Aug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
Consequence & remedy
Consequence: A vehicle stall can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
14V631000 · Electrical System; Visibility:rearview Mirrors/devices:exterior
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
Additional source detail variants (2)
Visibility:rearview Mirrors/devices:exterior
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
Consequence: An electrical short increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
Electrical System
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
Consequence: An electrical short increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
07V291000 · Electrical System
Jul 3, 2007
ON CERTAIN VEHICLES, THE TOTALLY INTEGRATED POWER MODULE (TIPM) WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN OPERATING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE TIPM. THE RECALL BEGAN ON JULY 5, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
02V075000 · Electrical System:ignition:switch
Mar 8, 2002
ON CERTAIN SPORT UTILITY VEHICLES, WATER AND IMPURITIES CAN ENTER INTO THE IGNITION SWITCH, CAUSING A SHORT CIRCUIT.
Consequence & remedy
Consequence: THIS COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALERS WILL REPLACE THE IGNITION SWITCH WITH A REDESIGNED SWITCH. OWNER NOTIFICATION BEGAN APRIL 8, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
93V083000 · Electrical System:ignition:switch
May 11, 1993
SALT CORROSION PRODUCTS BETWEEN THE STARTER SOLENOID WIRE AND THE ADJACENT BATTERY FEED IN THE BULKHEAD CONNECTOR MAY SHORT THESE CONNECTIONS, CAUSING THE CIRCUIT TO BYPASS THE IGNITION KEY CONTROL OF THE STARTER MOTOR SOLENOID. THE CAR CAN START WITHOUT THE STARTER SEQUENCE BEING INITIATED BY THE IGNITION KEY IN THE IGNITION LOCK.
Consequence & remedy
Consequence: THE UNINTENDED START OF A VEHICLE WITH A MANUALTRANSMISSION LEFT IN A DRIVE GEAR CAN RESULT IN A RUNAWAY VEHICLE.
Remedy: THE STARTER SOLENOID WIRING WILL BE SEPARATED FROM THE BATTERY FEED WIRE BY RELOCATING IT WITHIN THE BULKHEAD CONNECTOR ON AFFECTED VEHICLES.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
Related NHTSA investigations
6PE25014 · Instrument Panel Cluster (ipc) Failure
Opened Oct 23, 2025 · No close date supplied
Status: open (inferred from source dates) · Electrical System: Instrument Cluster/panel
The Office of Defects Investigations (ODI) is opening a Preliminary Evaluation on 2020 Model Year Jeep Gladiators and Wranglers involving a malfunctioning Instrument Panel Clusters (IPC) resulting in the loss of important vehicle metrics and other status information. ODI has received 89 Vehicle Owner Questionnaires (VOQs) alleging a complete or partial loss of the IPC display while driving. The subject vehicles' IPC display includes the speedometer, fuel gauge, engine temperature, turn signal indicators, warning light, and other gauges that are normally illuminated while the vehicle is in operation. Loss of the fuel gauge while driving may lead to an inability to determine the fuel level and result in a loss of motive power, and the loss of other safety-related information may impede a driver’s ability to take action to prevent a safety risk. Furthermore, an IPC that is suddenly not visible to the driver may divert the driver’s attention from the driving task, potentially causing a vehicle crash. ODI is opening this Preliminary Evaluation to evaluate the scope, severity and frequency of the alleged IPC malfunctions and to assess potential safety-related consequences. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov
RQ24012 · Loss Of Motive Power
Opened Jul 5, 2024 · No close date supplied
Status: open (inferred from source dates) · Electrical System; Engine
The Office of Defects Investigation (ODI) has identified 68 Vehicle Owner Questionnaire (VOQ) reports for model years (MY) 2021 through 2024 Jeep Wrangler 4xe vehicles alleging a loss of motive power. Recall 22V-865 was issued by the manufacturer to address an engine shutdown condition in certain MY 2021-2023 Wrangler 4xe vehicles. The complaints noted here contain both post recall remedy failures and failures in vehicles not included within the scope of 22V-865. An analysis comparing complaints received before the issuance of recall 22V-865 and complaints outside the scope of the recall has been conducted. The results show the current complaint rate is higher in the out of scope vehicles than it was for vehicles that were later covered by the recall. ODI is opening this Recall Query (RQ) to assess the severity of the alleged defect in vehicles not included in recall 22V-865.ODI will also assess the scope and remedy effectiveness of the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Electrical System
The Office of Defects Investigation (ODI) has identified 68 Vehicle Owner Questionnaire (VOQ) reports for model years (MY) 2021 through 2024 Jeep Wrangler 4xe vehicles alleging a loss of motive power. Recall 22V-865 was issued by the manufacturer to address an engine shutdown condition in certain MY 2021-2023 Wrangler 4xe vehicles. The complaints noted here contain both post recall remedy failures and failures in vehicles not included within the scope of 22V-865. An analysis comparing complaints received before the issuance of recall 22V-865 and complaints outside the scope of the recall has been conducted. The results show the current complaint rate is higher in the out of scope vehicles than it was for vehicles that were later covered by the recall. ODI is opening this Recall Query (RQ) to assess the severity of the alleged defect in vehicles not included in recall 22V-865.ODI will also assess the scope and remedy effectiveness of the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
The Office of Defects Investigation (ODI) has identified 68 Vehicle Owner Questionnaire (VOQ) reports for model years (MY) 2021 through 2024 Jeep Wrangler 4xe vehicles alleging a loss of motive power. Recall 22V-865 was issued by the manufacturer to address an engine shutdown condition in certain MY 2021-2023 Wrangler 4xe vehicles. The complaints noted here contain both post recall remedy failures and failures in vehicles not included within the scope of 22V-865. An analysis comparing complaints received before the issuance of recall 22V-865 and complaints outside the scope of the recall has been conducted. The results show the current complaint rate is higher in the out of scope vehicles than it was for vehicles that were later covered by the recall. ODI is opening this Recall Query (RQ) to assess the severity of the alleged defect in vehicles not included in recall 22V-865.ODI will also assess the scope and remedy effectiveness of the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
PE07027 · Engine Stalling & Electric Power Loss
Opened May 29, 2007 · Closed Aug 2, 2007
Status: closed (inferred from source dates) · Electrical System; Engine And Engine Cooling; Power Train:automatic Transmission; Power Train:manual Transmission
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Additional source detail variants (4)
Electrical System
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Engine And Engine Cooling
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Power Train:automatic Transmission
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Power Train:manual Transmission
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
RQ99011 · Instrument Panel Ground Screw
Opened Jun 1, 1999 · Closed May 30, 2000
Status: closed (inferred from source dates) · Electrical System
THE INSTRUMENT PANEL WIRING GROUND ATTACHMENT SCREWS CAN LOOSEN