CRINKLING NOISE WHEN TURNING THE WHEEL EITHER WAY, HORN RANDOMLY HONKS, RED AIR BAG ON, BAS ESP LIGHT ON
2009 Jeep Wrangler
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Jeep Wrangler do not stand out strongly from the model-year median of 265.
About this comparison →How this year compares
Owner complaints by model year
Compare all Wrangler years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
294 reports with mileage · 77 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 103 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 65 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 63 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
371 reportshorn honks on its own, crinkling while turning wheel, airbag light on dash, esp, bas lights on dash
The ABS control module (part 68032358AC, ATE 25.0212-1155.4) on my 2009 Jeep Wrangler Unlimited failed at approximately 109,600 miles with stored diagnostic code C2200 (Anti-lock Brake Module Internal). The ABS, BRAKE, ESP/BAS, and traction control warning lights illuminate intermittently and the fault is permanently stored. Whe…
Read full complaint
The ABS control module (part 68032358AC, ATE 25.0212-1155.4) on my 2009 Jeep Wrangler Unlimited failed at approximately 109,600 miles with stored diagnostic code C2200 (Anti-lock Brake Module Internal). The ABS, BRAKE, ESP/BAS, and traction control warning lights illuminate intermittently and the fault is permanently stored. When active, the vehicle loses anti-lock braking, electronic stability control, and traction control; base hydraulic braking remains. This internal module failure is widely reported among 2007–2018 Wrangler JK owners. The replacement part has also been discontinued — my mechanic and a Jeep dealership confirmed it is unavailable nationwide through the Mopar network, leaving no new manufacturer replacement available for this safety component. No crash or injury has occurred.
The contact owns a 2009 Jeep Wrangler. The contact received notifications of NHTSA Campaign Numbers: 10V236000 (Service Brakes, Hydraulic), 16V290000 (Air Bags), and 18V021000 (Air Bags); however, the parts required to complete the recall repairs were not available. The contact stated that the dealer had been contacted several t…
Read full complaint
The contact owns a 2009 Jeep Wrangler. The contact received notifications of NHTSA Campaign Numbers: 10V236000 (Service Brakes, Hydraulic), 16V290000 (Air Bags), and 18V021000 (Air Bags); however, the parts required to complete the recall repairs were not available. The contact stated that the dealer had been contacted several times. The vehicle was not diagnosed or repaired. The dealer confirmed that parts were not yet available and were on back order. The dealer informed the contact that parts for NHTSA Campaign Number: 10V23600 (Service Brakes, Hydraulic); had been discontinued. The manufacturer was made aware of the issue and confirmed that the parts were discontinued. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The contact had not experienced a failure.
The contact owns a 2009 Jeep Wrangler. The contact received notifications of NHTSA Campaign Numbers: 18V021000 (Air Bags) and 16V290000 (Air Bags); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The dealer was…
Read full complaint
The contact owns a 2009 Jeep Wrangler. The contact received notifications of NHTSA Campaign Numbers: 18V021000 (Air Bags) and 16V290000 (Air Bags); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The dealer was contacted and confirmed that the parts were not yet available. The dealer had been waiting for parts for over a month and a half for parts to repair another vehicle. The contact called several other dealers; however, parts were not available. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
I was driving approximately 55mph 10/22/2024 on a two-lane roadway in my 2009 Jeep Wrangler X (VIN: [XXX] ) when another vehicle pulled out in front of me. I struck that vehicle in a frontal collision. The force of the impact caused my Jeep to ride up and over the vehicle, enter the opposite lane of travel, and roll over a secon…
Read full complaint
I was driving approximately 55mph 10/22/2024 on a two-lane roadway in my 2009 Jeep Wrangler X (VIN: [XXX] ) when another vehicle pulled out in front of me. I struck that vehicle in a frontal collision. The force of the impact caused my Jeep to ride up and over the vehicle, enter the opposite lane of travel, and roll over a second vehicle before continuing to roll down the road. Despite the high-speed frontal impact and subsequent rollover, none of the airbags in my vehicle deployed, including the driver frontal airbag. The other vehicles involved in the crash did experience airbag deployment. The crash resulted in significant vehicle damage, including roof deformation consistent with rollover forces. Given the severity of the impact and rollover, I believe the airbags should have deployed. The failure of the airbag system may have contributed to the injuries I sustained. I am concerned that there was a failure of the airbag or restraint system in my vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Turned on ignition and wipers and headlights turned on with no control, car ignition beeped constantly, all dash lights illuminated, all gauges stopped working (speedometer, fuel, tachometer, temperature) and there was a clicking noise on the transmission. Had to drive home hoping my electrical system wouldn’t shut down while dr…
Read full complaint
Turned on ignition and wipers and headlights turned on with no control, car ignition beeped constantly, all dash lights illuminated, all gauges stopped working (speedometer, fuel, tachometer, temperature) and there was a clicking noise on the transmission. Had to drive home hoping my electrical system wouldn’t shut down while driving home. Narrowed down to faulty TIPM.
My wrangler's brakes locked up repeatedly and I took it to the dealer. They said that it needs a new ABS module but that part is not made anymore. This is a safety issue and I now have a car that I can't sell, can't fix, and can't drive. My wife almost got into an accident.
When filling my tank, it spits gas back out of the nozzle. I’ve been told in several forums that this is a warranty issue and is to be replaced by a dealership for free. The item that needs to be repaired is a fuel filler tube. I don’t wanna spend the money on buying the part myself if this is something that is covered by the de…
Read full complaint
When filling my tank, it spits gas back out of the nozzle. I’ve been told in several forums that this is a warranty issue and is to be replaced by a dealership for free. The item that needs to be repaired is a fuel filler tube. I don’t wanna spend the money on buying the part myself if this is something that is covered by the dealership through the factory. This happens every time I fill the tank and has been an ongoing problem for over a year almost 2 years. I have to fill it very slowly with gas as well. I cannot fill it fast as it will stop automatically. The part number is 52060489AH
The manual transmission malfunctioned, it is available for inspection upon request. My safety and others are put at risk due to the transmission not accepting first gear when in 1st gear, and it “pops” out of gear unexpectedly, leaving me and others in the middle of an intersection. The problem has been reproduced and confirmed …
Read full complaint
The manual transmission malfunctioned, it is available for inspection upon request. My safety and others are put at risk due to the transmission not accepting first gear when in 1st gear, and it “pops” out of gear unexpectedly, leaving me and others in the middle of an intersection. The problem has been reproduced and confirmed by dealers, the manufacturer knows about the problem, to my knowledge. There were not any warning lamps, messages or other symptoms prior to the failure. This issue happens very frequently, and happens to thousands of others with this Jeep. And it’s extremely dangerous.
Official recalls
618V021000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
16V352000 · Air Bags:frontal:passenger Side:inflator Module
May 24, 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
Consequence & remedy
Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
16V290000 · Air Bags:frontal:driver Side:inflator Module
May 11, 2016
Chrysler (FCA US LLC) is recalling certain model year 2007-2010 Jeep Wrangler JK vehicles manufactured March 2, 2006, to August 13, 2010. The clockspring assembly may become contaminated with dust and cause the air bag circuit to fail.
Consequence & remedy
Consequence: Failure of the air bag circuit may prevent the driver's frontal air bag from deploying in the event of a crash, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will replace the clockspring, wheel back cover, and column shroud, free of charge. The recall began on December 14, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S33.
13V176000 · Air Bags
May 7, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 Jeep Wrangler right-hand drive vehicles manufactured February 1, 2007, through October 10, 2011. The affected vehicles have airbag clockspring assemblies that could experience broken airbag circuits.
Consequence & remedy
Consequence: In the event of a crash necessitating airbag deployment, a broken electrical circuit in the airbag clockspring wiring assembly can lead to non-deployment of the driver-side frontal airbag and will not be able to properly protect the driver, increasing the risk of injuries.
Remedy: Chrysler will notify owners, and dealers will replace the clockspring and add a steering wheel dust shield, free of charge. The recall began on June 10, 2013. Owners may contact Chrysler at 1-800-247-9753. This recall supercedes NHTSA recall 11V-528. Chrysler's recall campaign number is M31.
11V528000 · Air Bags:frontal
Nov 2, 2011
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2012 RIGHT HAND DRIVE (RHD) JEEP WRANGLER VEHICLES MANUFACTURED FROM FEBRUARY 1, 2007, THROUGH OCTOBER 10, 2011. SOME VEHICLES MAY BE EQUIPPED WITH DRIVER'S AIRBAG CLOCKSPRING ASSEMBLIES THAT COULD EXPERIENCE A COMPROMISED AIRBAG CIRCUIT RESULTING IN AN AIRBAG LAMP ILLUMINATION, WHICH INDICATES THAT THE AIRBAG MAY NOT DEPLOY.
Consequence & remedy
Consequence: A BROKEN ELECTRICAL CIRCUIT IN THE AIRBAG CLOCKSPRING WIRING ASSEMBLY CAN LEAD TO NON-DEPLOYMENT OF THE DRIVER FRONTAL AIRBAG AND WILL NOT BE ABLE TO PROPERLY PROTECT THE DRIVER IN THE EVENT OF A CRASH, INCREASING THE RISK OF INJURIES.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND REMEDY THE VEHICLES AS NECESSARY FREE OF CHARGE. CHRYSLER WILL MAIL TO OWNERS AN INTERIM NOTIFICATION DURING MARCH 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
10V236000 · Service Brakes, Hydraulic
Jun 3, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 JEEP WRANGLER LEFT AND RIGHT HAND DRIVE PASSENGER VEHICLES MANUFACTURED FROM MAY 15, 2006 THROUGH APRIL 22, 2010. THERE MAY BE CONTACT BETWEEN THE RIGHT AND LEFT FRONT INNER FENDER LINERS AND THE RIGHT FRONT AND LEFT REAR BRAKE TUBES WHICH COULD CAUSE WEAR OF THE TUBES CAUSING A BRAKE FLUID LEAK.
Consequence & remedy
Consequence: A BRAKE FLUID LEAK CAN CAUSE PARTIAL LOSS OF SERVICE BRAKES AT THE AFFECTED WHEEL INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA15007 · Air Bag Clockspring Wiring Failure
Opened Dec 4, 2015 · Closed Jul 6, 2016
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.
Additional source detail variants (4)
Air Bags
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.
Air Bags
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.
Air Bags:frontal
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.
Air Bags:frontal
On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.
PE15025 · Air Bag Clockspring Wiring Failure
Opened Jun 19, 2015 · Closed Dec 7, 2015
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal
In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.
Additional source detail variants (2)
Air Bags
In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.
Air Bags:frontal
In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.
DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
Illustration