2,974 distinct owner reports with an electrical-system component in this snapshot.
Includes the electrical-system component and its detailed subcategories. Related recalls and investigations must also name this component; they are not linked by narrative keyword alone.
Reports by model year
Recall and investigation columns show each year’s full history. A report naming several years can appear in more than one row.
When problems were reported
Mileage at the reported incident
1,114 reports with mileage · 1,860 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What owners actually said
2,974 reportsElectrical SystemEngineSteering
I was driving as normal in a 40mph zone when my car stalled, steering locked up, and it flashed to put it in park in the middle of traffic. I was able to move over to a safe space after putting it in park but it kept shutting off as I inched my way off the road with hazards on. There was an update that went out that was causing…
Read full complaint
I was driving as normal in a 40mph zone when my car stalled, steering locked up, and it flashed to put it in park in the middle of traffic. I was able to move over to a safe space after putting it in park but it kept shutting off as I inched my way off the road with hazards on. There was an update that went out that was causing this to vehicles and i was declining the update as suggested by manufactuerer by pressing the red X but it somehow forced installed itself while I was driving. Then while i was pulled over it would run for a few seconds then it would all of a sudden shut off again saying E-Drive Mode Temporairly Unavailable. Ive attached some photos but have a video of it running and shutting off if you would like me to send that.
NHTSA ODI #11693903
Electrical SystemEnginePower Train
We were driving the car after a faulty over the air update that forced the car to shut down while driving. My kids were in the car this created a very dangerous situation. We were able to “limp” it to a parking lot but it could have been more dangerous had we been on a freeway.
NHTSA ODI #11693840
Electrical SystemFuel/propulsion System
Jeep wanted to do an OTA update through the connect service. I continued to select 'update later' for several days then it all of a sudden my uconnect service told me it was updating. Immediately after it was updated, while on the road, the screened flashed off then back on just like it does at start up wanting me to start th…
Read full complaint
Jeep wanted to do an OTA update through the connect service. I continued to select 'update later' for several days then it all of a sudden my uconnect service told me it was updating. Immediately after it was updated, while on the road, the screened flashed off then back on just like it does at start up wanting me to start the vehicle. At this point we were at a stoplight and wasn't actively moving at this time. It was already running, and when the button was pressed, it turned, off, then pressed again and turned back on and restarted with on with CEL. I was only a mile from my local dealership, so I proceeded to go there.
NHTSA ODI #11693770
Electrical SystemEngineSteering
While driving my 2024 Jeep Rubicon 4xe, both the Check Engine and “Service Battery” lights came on, and the vehicle suddenly shut down completely in the middle of a busy intersection. I lost all ability to accelerate, steer, or brake — the steering wheel locked, and the vehicle was inoperable in heavy traffic. I was trapped in t…
Read full complaint
While driving my 2024 Jeep Rubicon 4xe, both the Check Engine and “Service Battery” lights came on, and the vehicle suddenly shut down completely in the middle of a busy intersection. I lost all ability to accelerate, steer, or brake — the steering wheel locked, and the vehicle was inoperable in heavy traffic. I was trapped in the lane with vehicles approaching from all directions, unable to move or control the car in any way. It was a frightening and dangerous experience that could have resulted in a serious accident. This was the second time this same issue occurred. The first happened around May 17, 2024, when the vehicle had approximately 500 miles. The dealership repaired it under warranty and returned it to me. The most recent incident occurred around October 10, 2025, at approximately 10,000 miles. The San Leandro Jeep Dodge Ram Chrysler dealership inspected the vehicle and confirmed that Jeep engineering is aware of the problem and that a fix is being developed, but there is no known repair or release timeline. They stated the only option was to clear the codes and return the vehicle. This is also my second Jeep 4xe to experience the exact same issue. My previous 4xe was repurchased by the manufacturer (FCA/Stellantis) in 2023 after similar “Service Battery” warnings and total shutdowns while driving. This ongoing defect is a severe safety hazard. The vehicle can lose all power, propulsion, and steering without warning, leaving the driver and others on the road in immediate danger. A total loss of control — especially while crossing an intersection or driving at speed — could easily result in a crash or fatal injury.
NHTSA ODI #11693763
Electrical SystemEnginePower Train
Put a brand new battery in my vehicle - 3 days later driving on the highway had full loss of power - if said to service the charging system, and to put the car in park, then to press the brake and start button to start the vehicle. Went from 75MPH to 25MPH - rolled off the highway.
NHTSA ODI #11693752
Electrical SystemEngineFuel/propulsion System
Driving normally then loss of power and forced us to pull over. Check engine light on. Super, super dangerous. This is after an OTA update. Many other jeep wrangler owners reporting the same issue: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11693843
Electrical SystemEngineService Brakes
Jeep 4xe complete loss of power while driving almost caused a huge accident. No power, no power steering TOTALLY dangerous and they knew damn well this would happen but didn't alert customers!!!
NHTSA ODI #11693664
Electrical SystemEngineFuel/propulsion System
I was driving from New York to DC when my car “bricked” on [XXX] my car advised me to go into park mode and began slowing down to a stop (I had no control over it) and luckily I was able pull over onto the shoulder to where I felt very unsafe and waited to restart my car. I was able to restart and try again and it bricked again…
Read full complaint
I was driving from New York to DC when my car “bricked” on [XXX] my car advised me to go into park mode and began slowing down to a stop (I had no control over it) and luckily I was able pull over onto the shoulder to where I felt very unsafe and waited to restart my car. I was able to restart and try again and it bricked again about 10 minutes later. I was terrified and had a panic attack before being able to safely merge across lanes into a rest stop. I figured that if I switched into gas mode because it appeared to be an electrical problem that I might be able to continue my drive I started driving and not five minutes later I was stalled on a bridge. It was the scariest experience I’ve had probably ever in my life I had to completely shut down my car and restart it just to inch my way onto a shoulder after getting across a bridge with other cars going over 60 70 mph. Eventually I was able to disconnect the battery and reconnect it just in order to make it safely to a dealership with my father, following behind me. Because the check engine light went off when the battery was reconnected, when I got there, the dealership told me the diagnostic test showed no concerns and said that I could take the car and continue my drive. then 15 minutes after continuing my drive it stalled again, again on the highway! So I made my way back to the dealership and in the 10 miles that it took to get to the dealership the car stalled over five more times every single time it stalled I risked someone running into the back end of my car. I was told to contact Chrysler for a customer care case and they were not helpful at all. I was given a loaner that I couldn’t take out of state so I couldn’t get back to New York in a timely fashion so I had to wait in DC an extra day just to get my car back. I still don’t feel safe in the vehicle because a little software glitched caused such a major issue. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11693562
Electrical SystemEnginePower Train
After an OTA update, while driving, the vehicle abruptly stopped working and I was forced to pull over. The check engine light went on and a message requesting service to the electric charging module was shown. After cycling power a few times the car worked again. This happened again on the way home. The manufacturer JeepCares a…
Read full complaint
After an OTA update, while driving, the vehicle abruptly stopped working and I was forced to pull over. The check engine light went on and a message requesting service to the electric charging module was shown. After cycling power a few times the car worked again. This happened again on the way home. The manufacturer JeepCares account advised that the car needs to be towed to a dealer immediately.
NHTSA ODI #11693555
Electrical SystemEngine
Jeep pushed out an update on Friday 10/10 that we were advised to decline as it was causing mechanical failures. Despite declining the update ever since, and being assured that this remedy would work until the update expired in 30 days, apparently it still managed to push through on its own last night. I was less than two miles …
Read full complaint
Jeep pushed out an update on Friday 10/10 that we were advised to decline as it was causing mechanical failures. Despite declining the update ever since, and being assured that this remedy would work until the update expired in 30 days, apparently it still managed to push through on its own last night. I was less than two miles from my house this morning on my way to an appointment when the dashboard lit up and the Jeep completely lost power. I shut it off, turned it back on and was able to get back home, but the CEL is still on. I was lucky enough to be on a side road, as I was about to enter a busy intersection. I've talked to Jeep and they do not have a fix, but it is unsafe to drive at this point. I am waiting on a towing company at the moment to bring it to a Jeep dealership.
NHTSA ODI #11693528
Related Official recalls
12Oct 30, 2025
Chrysler (FCA US, LLC) is recalling certain 2020-2025 Jeep Wrangler 4Xe and 2022-2026 Grand Cherokee 4Xe vehicles. The high voltage battery may fail internally and lead to a vehicle fire while parked or driving.
Consequence & remedy
Consequence: A vehicle fire can increase the risk of injury.
Remedy: Owners are advised to park outside and away from structures and not to charge their vehicles until the remedy is completed. Dealers will update the high voltage battery software, and replace the high voltage battery, as necessary, free of charge. Some owner notification letters were mailed beginning December 17, 2025. The remaining owner notification letters will be mailed at a later date. Owners may contact Chrysler customer service at 800-853-1403. Chrysler's number for this recall is 68C. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning November 6, 2025. Vehicles that were previously recalled for the same issue under NHTSA Recalls 24V720 and 23V787 will need to have the new remedy performed.
Nov 19, 2024
Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wrangler vehicles. The incorrect dash wiring harness was installed, which can result in inoperative trailer lighting. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: Trailer lights that fail to illuminate can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the dash wiring harness as necessary, free of charge. Owner notification letters were mailed December 19, 2024. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is B9B.
Additional source detail variants (2)
Exterior Lighting
Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wrangler vehicles. The incorrect dash wiring harness was installed, which can result in inoperative trailer lighting. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: Trailer lights that fail to illuminate can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the dash wiring harness as necessary, free of charge. Owner notification letters were mailed December 19, 2024. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is B9B.
Electrical System:wiring
Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wrangler vehicles. The incorrect dash wiring harness was installed, which can result in inoperative trailer lighting. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: Trailer lights that fail to illuminate can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the dash wiring harness as necessary, free of charge. Owner notification letters were mailed December 19, 2024. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is B9B.
Sep 5, 2024
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
Consequence & remedy
Consequence: An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Remedy: Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
Nov 22, 2023
Chrysler (FCA US, LLC) is recalling certain 2021-2023 Jeep Wrangler Plug-In Hybrid Electric (PHEV) vehicles. The high voltage battery may fail internally and lead to a vehicle fire while parked or driving.
Consequence & remedy
Consequence: A vehicle fire while parked or driving can increase the risk of injury.
Remedy: Owners are advised not to recharge their vehicles, and to park outside and away from structures, until they are repaired. Dealers will update the high voltage battery pack software and replace the battery pack assembly if necessary, free of charge. Owner notification letters were mailed March 7, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 89A. This recall is superseded by NHTSA Recall 24V-720.
Apr 27, 2023
Chrysler (FCA US, LLC) is recalling certain 2022-2023 Jeep Wrangler Plug-In Hybrid Electric vehicles (PHEV). The high voltage (HV) battery pack assembly was built with incorrect fasteners to secure the 200-amp fuse, which can generate excessive heat.
Consequence & remedy
Consequence: Excessive heat may cause the fuse to fail and result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the HV battery fuse, as necessary. Dealers will also inspect the battery assembly for damage and replace it, if necessary. Repairs will be performed free of charge. Owner notification letters were mailed May 23, 2023. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is 53A. This recall is an expansion of previous recall 22V-768.
Oct 13, 2022
Chrysler (FCA US, LLC) is recalling certain 2022-2023 Jeep Wrangler Plug-In Hybrid Electric (PHEV) vehicles. The high voltage (HV) battery pack assembly was built with incorrect fasteners to secure the 200-amp fuse, which can generate excessive heat.
Consequence & remedy
Consequence: Excessive heat may cause the fuse to fail and result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the HV battery fuse, as necessary. Dealers will also inspect the battery assembly for damage and replace it, if necessary. Repairs will be performed free of charge. Owner notification letters were mailed December 8, 2022. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is Z71.
Aug 9, 2018
Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.
Consequence & remedy
Consequence: A vehicle stall can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
Additional source detail variants (2)
Visibility:rearview Mirrors/devices:exterior
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
Consequence: An electrical short increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
Electrical System
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2013 Jeep Wrangler vehicles manufactured February 16, 2010, to July 19, 2013. Corrosion in the exterior heated power mirror electrical connector may result in an electrical short.
Consequence: An electrical short increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will move the exterior mirror power feed to a separate connector, free of charge. Chrysler issued an interim notification to owners on December 8, 2014. The recall began on March 3, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P61.
Jul 3, 2007
ON CERTAIN VEHICLES, THE TOTALLY INTEGRATED POWER MODULE (TIPM) WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN OPERATING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE TIPM. THE RECALL BEGAN ON JULY 5, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Mar 8, 2002
ON CERTAIN SPORT UTILITY VEHICLES, WATER AND IMPURITIES CAN ENTER INTO THE IGNITION SWITCH, CAUSING A SHORT CIRCUIT.
Consequence & remedy
Consequence: THIS COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALERS WILL REPLACE THE IGNITION SWITCH WITH A REDESIGNED SWITCH. OWNER NOTIFICATION BEGAN APRIL 8, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
May 11, 1993
SALT CORROSION PRODUCTS BETWEEN THE STARTER SOLENOID WIRE AND THE ADJACENT BATTERY FEED IN THE BULKHEAD CONNECTOR MAY SHORT THESE CONNECTIONS, CAUSING THE CIRCUIT TO BYPASS THE IGNITION KEY CONTROL OF THE STARTER MOTOR SOLENOID. THE CAR CAN START WITHOUT THE STARTER SEQUENCE BEING INITIATED BY THE IGNITION KEY IN THE IGNITION LOCK.
Consequence & remedy
Consequence: THE UNINTENDED START OF A VEHICLE WITH A MANUALTRANSMISSION LEFT IN A DRIVE GEAR CAN RESULT IN A RUNAWAY VEHICLE.
Remedy: THE STARTER SOLENOID WIRING WILL BE SEPARATED FROM THE BATTERY FEED WIRE BY RELOCATING IT WITHIN THE BULKHEAD CONNECTOR ON AFFECTED VEHICLES.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
Related NHTSA investigations
6PE25014 · Instrument Panel Cluster (ipc) Failure
Opened Oct 23, 2025 · No close date supplied
Status: open (inferred from source dates) · Electrical System: Instrument Cluster/panel
The Office of Defects Investigations (ODI) is opening a Preliminary Evaluation on 2020 Model Year Jeep Gladiators and Wranglers involving a malfunctioning Instrument Panel Clusters (IPC) resulting in the loss of important vehicle metrics and other status information. ODI has received 89 Vehicle Owner Questionnaires (VOQs) alleging a complete or partial loss of the IPC display while driving. The subject vehicles' IPC display includes the speedometer, fuel gauge, engine temperature, turn signal indicators, warning light, and other gauges that are normally illuminated while the vehicle is in operation. Loss of the fuel gauge while driving may lead to an inability to determine the fuel level and result in a loss of motive power, and the loss of other safety-related information may impede a driver’s ability to take action to prevent a safety risk. Furthermore, an IPC that is suddenly not visible to the driver may divert the driver’s attention from the driving task, potentially causing a vehicle crash. ODI is opening this Preliminary Evaluation to evaluate the scope, severity and frequency of the alleged IPC malfunctions and to assess potential safety-related consequences. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov
RQ24012 · Loss Of Motive Power
Opened Jul 5, 2024 · No close date supplied
Status: open (inferred from source dates) · Electrical System; Engine
The Office of Defects Investigation (ODI) has identified 68 Vehicle Owner Questionnaire (VOQ) reports for model years (MY) 2021 through 2024 Jeep Wrangler 4xe vehicles alleging a loss of motive power. Recall 22V-865 was issued by the manufacturer to address an engine shutdown condition in certain MY 2021-2023 Wrangler 4xe vehicles. The complaints noted here contain both post recall remedy failures and failures in vehicles not included within the scope of 22V-865. An analysis comparing complaints received before the issuance of recall 22V-865 and complaints outside the scope of the recall has been conducted. The results show the current complaint rate is higher in the out of scope vehicles than it was for vehicles that were later covered by the recall. ODI is opening this Recall Query (RQ) to assess the severity of the alleged defect in vehicles not included in recall 22V-865.ODI will also assess the scope and remedy effectiveness of the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Electrical System
The Office of Defects Investigation (ODI) has identified 68 Vehicle Owner Questionnaire (VOQ) reports for model years (MY) 2021 through 2024 Jeep Wrangler 4xe vehicles alleging a loss of motive power. Recall 22V-865 was issued by the manufacturer to address an engine shutdown condition in certain MY 2021-2023 Wrangler 4xe vehicles. The complaints noted here contain both post recall remedy failures and failures in vehicles not included within the scope of 22V-865. An analysis comparing complaints received before the issuance of recall 22V-865 and complaints outside the scope of the recall has been conducted. The results show the current complaint rate is higher in the out of scope vehicles than it was for vehicles that were later covered by the recall. ODI is opening this Recall Query (RQ) to assess the severity of the alleged defect in vehicles not included in recall 22V-865.ODI will also assess the scope and remedy effectiveness of the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
The Office of Defects Investigation (ODI) has identified 68 Vehicle Owner Questionnaire (VOQ) reports for model years (MY) 2021 through 2024 Jeep Wrangler 4xe vehicles alleging a loss of motive power. Recall 22V-865 was issued by the manufacturer to address an engine shutdown condition in certain MY 2021-2023 Wrangler 4xe vehicles. The complaints noted here contain both post recall remedy failures and failures in vehicles not included within the scope of 22V-865. An analysis comparing complaints received before the issuance of recall 22V-865 and complaints outside the scope of the recall has been conducted. The results show the current complaint rate is higher in the out of scope vehicles than it was for vehicles that were later covered by the recall. ODI is opening this Recall Query (RQ) to assess the severity of the alleged defect in vehicles not included in recall 22V-865.ODI will also assess the scope and remedy effectiveness of the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
PE07027 · Engine Stalling & Electric Power Loss
Opened May 29, 2007 · Closed Aug 2, 2007
Status: closed (inferred from source dates) · Electrical System; Engine And Engine Cooling; Power Train:automatic Transmission; Power Train:manual Transmission
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Additional source detail variants (4)
Electrical System
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Engine And Engine Cooling
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Power Train:automatic Transmission
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
Power Train:manual Transmission
ON JULY 3, 2007, DAIMLERCHRYSLER CORPORATION (DCC) SUBMITTED A DEFECT INFORMATION REPORT TO NHTSA DESCRIBING A DEFECT THAT COULD RESULT IN ENGINE STALL WHILE DRIVING IN APPROXIMATELY 80,894 MODEL YEAR (MY) 2007 JEEP WRANGLER AND DODGE NITRO VEHICLES MANUFACTURED BETWEEN JANUARY 30, 2006 AND JANUARY 22, 2007 (NHTSA RECALL 07V-291, DCC RECALL G25).ACCORDING TO DCC, THE TOTALLY INTEGRATED POWER MODULE (TIPM) IN THESE VEHICLES WAS PROGRAMMED WITH SOFTWARE THAT MAY ALLOW THE ENGINE TO STALL UNDER CERTAIN CONDITIONS.DCC WILL REPROGRAM THE TIPM IN THE RECALLED VEHICLES WITH REVISED SOFTWARE. ODI OPENED PE07-027 ON MAY 29, 2007, BASED ON 53 COMPLAINTS ALLEGING ENGINE STALL AND/OR LOSS OF ELECTRICAL POWER IN MY 2007 JEEP WRANGLER VEHICLES.ODI WAS ALSO MONITORING SIMILAR COMPLAINTS IN MY 2007 DODGE NITRO VEHICLES.DCC'S ANALYSIS OF COMPLAINTS TO DCC AND NHTSA FOUND THAT MANY DESCRIBED EVENTS WITH A MOMENTARY LOSS OF ELECTRICAL POWER INSIDE THE VEHICLE AND A CORRESPONDING LOSS OF ENGINE POWER.MANY OF THE REPORTS ALSO INDICATED THAT THE INSTRUMENT CLUSTER TELLTALE LAMPS MOMENTARILY ILLUMINATED DURING THE EVENT. DCC'S ENGINEERING ANALYSIS DETERMINED THAT THE TIPM COULD INITIATE AN INTERNAL RESET CYCLE LASTING APPROXIMATELY 75 MS IN RESPONSE TO ERROR MESSAGES ON THE COMMUNICATION BUS.THE KEY ON SIGNAL FROM THE TIPM TO THE POWERTRAIN CONTROL MODULE (PCM) IS LOST DURING A TIPM RESET.IF THE PCM LOSES THE KEY ON SIGNAL FOR LONGER THAN 40 MS, IT INTERPRETS IT AS THE VEHICLE IGNITION BEING TURNED OFF AND BEGINS A POWER DOWN ROUTINE.AFTER THE TIPM RESET, THE KEY ON SIGNAL IS RESTORED AND THE PCM POWERS BACK UP.IF THE ROTATING COMPONENTS OF THE ENGINE CONTAIN SUFFICIENT INERTIA, THE VEHICLE MAY RESTART WITH NO INPUT FROM THE OPERATOR AS REPORTED IN SOME OF THE COMPLAINTS.IF THE ENGINE DOES NOT RESTART IN THIS MANNER, IT CAN BE RESTARTED BY THE OPERATOR.A REVISION TO THE TIPM SOFTWARE ON JANUARY 22, 2007 CHANGED THE TIPM RESET TIME TO 17 MS, REMOVING THE POTENTIAL FOR PCM POWER DOWN AND ENGINE STALL. ODI HAS RECEIVED 178 COMPLAINTS POTENTIALLY RELATED TO THE ALLEGED DEFECT IN MY 2007 JEEP WRANGLER VEHICLES AND 52 COMPLAINTS INVOLVING MY 2007 DODGE NITRO VEHICLES.TWO OF THE NITRO COMPLAINTS ALLEGE THAT A CRASH RESULTED FROM AN ENGINE STALL INCIDENT, ONE OF WHICH CAUSED MINOR INJURIES TO A PASSENGER.AS OF JUNE 1, 2007, DCC IDENTIFIED 151 WRANGLER COMPLAINTS AND 128 NITRO COMPLAINTS. THIS INVESTIGATION HAS BEEN CLOSED WITH DCC'S RECALL.
RQ99011 · Instrument Panel Ground Screw
Opened Jun 1, 1999 · Closed May 30, 2000
Status: closed (inferred from source dates) · Electrical System
THE INSTRUMENT PANEL WIRING GROUND ATTACHMENT SCREWS CAN LOOSEN