IllustrationI WAS CHANGING THE OIL ON MY MAXIMA AND NOTICED BOTH DRIVERS AND PASSENGERS FLOOR BOARDS ALMOST TOTALLY RUSTED THROUGH. THIS IS A VERY DANGEROUS DUE TO SAFETY OF BOTH DRIVER AND PASSENGERS. AFTER LOOKING THROUGH THE COMPLAINT SECTION OF THIS WEBSITE IT SEEMS TO BE A VERY COMMON PROBLEM THAT NISSAN SHOULD NEED TO RECALL. *TR
2007 Nissan Maxima
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2007 Nissan Maxima do not stand out strongly from the model-year median of 99.
About this comparison →How this year compares
Owner complaints by model year
Compare all Maxima years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
100–25K
925–50K
2350–75K
2475–100K
31100–150K
8150K+
105 reports with mileage · 24 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Structure. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports1 fire reports3 injury reports
Structure complaints
33 reportsTHE DRIVER SIDE FLOORBOARD HAS BEGAN TO RUST THRU AS A RESULT OF A HOLE LEFT DURING MANUFACTURING. THIS SEEMS TO BE A DEFECT (SINCE IT IS NOT ON THE PASSENGER SIDE). AS A RESULT OF THE HOLE WATER AND SALT HAVE BEGAN TO RUST THROUGH THE DRIVER SIDE FLOORBOARD. MY VEHICLE WAS TAKEN TO A DEALER WHOM TOOK PICTURES AND SENT TO NISS…
Read full complaint
THE DRIVER SIDE FLOORBOARD HAS BEGAN TO RUST THRU AS A RESULT OF A HOLE LEFT DURING MANUFACTURING. THIS SEEMS TO BE A DEFECT (SINCE IT IS NOT ON THE PASSENGER SIDE). AS A RESULT OF THE HOLE WATER AND SALT HAVE BEGAN TO RUST THROUGH THE DRIVER SIDE FLOORBOARD. MY VEHICLE WAS TAKEN TO A DEALER WHOM TOOK PICTURES AND SENT TO NISSAN. NISSAN'S RESPONSE WAS THE VEHICLE IS OUT OF WARRANTY AND IT IS A RESULT OF BEING IN AN AREA HAT USES SALT DURING WINTER. FORTUNATELY IT LOOKS LIKE THE RUST WAS DETECTED BEFORE IT REACHED THE DRIVER SIDE SEAT WHICH WOULD CAUSE A SAFETY ISSUE (ESPECIALLY DURING AN ACCIDENT). ONE DOES NOT EXPECT A FLOORBOARD TO RUST THRU ON A SEVEN YEAR OLD VEHICLE WITH LOW MILEAGE. *TR
AIRBAG WARNING LIGHT WON'T TURN OFF. I'M WORRIED IT WILL SPONTANEOUSLY DEPLOY AT ANYTIME. IT IS THE OPINION OF VARIOUS CAR WASH ESTABLISHMENTS THAT ROOF AND HOOD PAINT IS A COMMON DEFECT ON NISSAN VEHICLES, INCLUDING MINI-VANS. MY CAR'S HOOD AND ROOF LOOK LIKE I'VE LIVED BY THE SEA FOR YEARS. TRUTH IS THAT I'VE ALWAYS LIVED INLA…
Read full complaint
AIRBAG WARNING LIGHT WON'T TURN OFF. I'M WORRIED IT WILL SPONTANEOUSLY DEPLOY AT ANYTIME. IT IS THE OPINION OF VARIOUS CAR WASH ESTABLISHMENTS THAT ROOF AND HOOD PAINT IS A COMMON DEFECT ON NISSAN VEHICLES, INCLUDING MINI-VANS. MY CAR'S HOOD AND ROOF LOOK LIKE I'VE LIVED BY THE SEA FOR YEARS. TRUTH IS THAT I'VE ALWAYS LIVED INLAND. THERE'S NO REASON WHY MY CAR SHOULD LOOK 20 YEARS OLD! *TR
TL* THE CONTACT OWNS A 2007 NISSAN MAXIMA. THE CONTACT STATED THAT THERE WAS CORROSION PRESENT AND A HOLE LOCATED ON THE DRIVER SIDE FLOORBOARD. THE VEHICLE HAD BEEN TAKEN TO DEALER FOR A DIAGNOSIS AND STATED THEY WOULD HAVE TO EJECT THE DRIVER'S SEAT FROM THE VEHICLE, WELD NEW MEDAL TO COVER THE HOLE AND PUT AN UNDER COATING …
Read full complaint
TL* THE CONTACT OWNS A 2007 NISSAN MAXIMA. THE CONTACT STATED THAT THERE WAS CORROSION PRESENT AND A HOLE LOCATED ON THE DRIVER SIDE FLOORBOARD. THE VEHICLE HAD BEEN TAKEN TO DEALER FOR A DIAGNOSIS AND STATED THEY WOULD HAVE TO EJECT THE DRIVER'S SEAT FROM THE VEHICLE, WELD NEW MEDAL TO COVER THE HOLE AND PUT AN UNDER COATING ON THE WELD NEW MEDAL. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 74,000.
PASSENGERS SIDE FRONT FLOOR PAN RUSTED THROUGH AS IF CAR IS 40 YEARS OLD. NOT ONLY IS THIS A BODY FRAME DEFECT BUT A SAFETY ISSUE. HUNDREDS OF ON LINE FORUMS NOTE THE PROBLEM IS OBVIOUS AND NISSAN REFUSES TO ADMIT DESIGN DEFECT. THIS DEFECT JUSTIFIES A RECALL FOR REPAIR OTHERWISE VALUE OF VEHICLE HAS BEEN SIGNIFICANTLY DIMINIS…
Read full complaint
PASSENGERS SIDE FRONT FLOOR PAN RUSTED THROUGH AS IF CAR IS 40 YEARS OLD. NOT ONLY IS THIS A BODY FRAME DEFECT BUT A SAFETY ISSUE. HUNDREDS OF ON LINE FORUMS NOTE THE PROBLEM IS OBVIOUS AND NISSAN REFUSES TO ADMIT DESIGN DEFECT. THIS DEFECT JUSTIFIES A RECALL FOR REPAIR OTHERWISE VALUE OF VEHICLE HAS BEEN SIGNIFICANTLY DIMINISHED. SEE: HTTP://MAXIMA.ORG/FORUMS/6TH-GENERATION-MAXIMA-2004-2008/655476-FLOOR-PAN-RUST-ANYONE.HTML. *TR
DRIVERS FLOOR BOARD STRUCTURE IS RUSTED OUT, I DO NOT FEEL SAFE LETTING MY WIFE DRIVE THIS CAR. *TR
TL* THE CONTACT OWNS A 2007 NISSAN MAXIMA. THE CONTACT STATED THAT WHILE THE VEHICLE WAS BEING SERVICED FOR ROUTINE MAINTENANCE, THE MECHANIC NOTICED THAT THE FRONT DRIVER AND PASSENGER SIDE FLOORBOARDS WERE SEVERELY CORRODED AND RUSTED. THE VEHICLE WAS NOT REPAIRED AND THE MANUFACTURER WAS NOTIFIED. THE FAILURE MILEAGE WAS 55,…
Read full complaint
TL* THE CONTACT OWNS A 2007 NISSAN MAXIMA. THE CONTACT STATED THAT WHILE THE VEHICLE WAS BEING SERVICED FOR ROUTINE MAINTENANCE, THE MECHANIC NOTICED THAT THE FRONT DRIVER AND PASSENGER SIDE FLOORBOARDS WERE SEVERELY CORRODED AND RUSTED. THE VEHICLE WAS NOT REPAIRED AND THE MANUFACTURER WAS NOTIFIED. THE FAILURE MILEAGE WAS 55,000. UPDATED 8/22/14*CN
WHILE VEHICLE WAS IN SHOP I WAS ALERTED TO THE FACT BOTH FRONT BOARDS WERE RUSTED THROUGH TO THE GROUND. *TR
I TOOK MY NISSAN IN FOR A ROUTINE OIL CHANGE AT PEP BOYS AND WAS IMMEDIATELY NOTIFIED OF RUST ON THE FLOOR BOARDS ON BOTH SIDES OF THE CAR. IT WAS BROUGHT TO MY ATTENTION THAT THE DRIVER SIDE IS BECOMING A SAFETY ISSUE AND CAN FAIL AT ANY TIME DUE TO THE SEVERITY OF THE PROBLEM. I NOTIFIED MY LOCAL NISSAN DEALERSHIP AND WAS GIVE…
Read full complaint
I TOOK MY NISSAN IN FOR A ROUTINE OIL CHANGE AT PEP BOYS AND WAS IMMEDIATELY NOTIFIED OF RUST ON THE FLOOR BOARDS ON BOTH SIDES OF THE CAR. IT WAS BROUGHT TO MY ATTENTION THAT THE DRIVER SIDE IS BECOMING A SAFETY ISSUE AND CAN FAIL AT ANY TIME DUE TO THE SEVERITY OF THE PROBLEM. I NOTIFIED MY LOCAL NISSAN DEALERSHIP AND WAS GIVEN A QUOTE FOR THE REPAIRS. I FORWARDED SAID QUOTE TO CONSUMER AFFAIRS AT NISSAN OF NORTH AMERICA AND WAS LATER NOTIFIED THAT THE MANUFACTURE DECLINED ANY SOLUTION TO MY PROBLEM. IT HAS COME TO MY ATTENTION THAT MANY CARS OF THE SAME MAKE AND MODEL HAVE THE SAME EXACT ISSUE. IT HAS BEEN REPORTED BEFORE BOTH WITH THE NHTSA AS WELL AS THE BBB. IF IT IS A PREVALENT PROBLEM THE MANUFACTURER SHOULD TAKE RESPONSIBILITY FOR THE DEFECT AND TRY TO REPAIR ALL ISSUES BEFORE PEOPLE ARE HURT. THE REPAIRS ARE EXTENSIVE, LABOR CONSUMING AND EXPENSIVE. *TR
2007 NISSAN MAXIMA. CONSUMER WRITES IN REGARDS TO CORROSION IN THE FLOOR BOARDS, ON BOTH THE DRIVER'S AND PASSENGER SIDE. *SMD
Official recalls
106V402000 · Steering:column LOCKING:ANTI-THEFT Device
Oct 23, 2006
CERTAIN PASSENGER VEHICLES EQUIPPED WITH AN 'INTELLIGENT KEY' FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION." DURING AN INSPECTION OF SOME VEHICLES AT THE ASSEMBLY PLANT, IT WAS FOUND THAT THE STEERING WHEEL WAS LOCKED WITH THE IGNITION KNOB IN THE "OFF" POSITION BUT THE VEHICLE TRANSMISSION NOT BEING IN THE "PARK" POSITION.
Consequence & remedy
Consequence: IF THE KEY IS TURNED TO THE "OFF" POSITION WITHOUT THE TRANSMISSION BEING IN THE "PARK" POSITION, IT IS POSSIBLE THAT THE STEERING WHEEL CAN LOCK WHEN TURNED TO THE RIGHT.
Remedy: DEALERS WILL INSPECT AND REPLACE THE STEERING WHEEL LOCK ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 18, 2006. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE08045 · Transmission Hose Leak
Opened Jul 23, 2008 · Closed Oct 24, 2008
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:cooling Unit And Lines
THIS PE WAS OPENED FOR MODEL YEAR (MY) 2008 NISSAN MAXIMA VEHICLES BASED ON EARLY WARNING DATA THAT THE AUTOMATIC TRANSMISSION COOLER HOSE MAY HAVE PINHOLES AND/OR CRACKS RESULTING IN A TRANSMISSION FLUID LEAK.THE LEAKED FLUID CAN CONTACT THE EXHAUST SYSTEM AND IGNITE.NISSAN HAS SHOWN THAT THE ROOT CAUSE OF THE PINHOLES AND/OR CRACKS IN THE HOSE IS EXCESSIVE STRESS DURING THE MANUFACTURE FORMING PROCESS RESULTING IN HOSE DEFORMATION AT LOADING ONTO A MANDREL, OR DAMAGE DURING UN-LOADING.REGARDING LOADING STRESS, NISSAN STATES, WHEN EXCESSIVE STRESS IS APPLIED WHILE LOADING THE HOSE ONTO THE MANDREL, HOSE DEFORMATION (WHICH LOOKS LIKE A BULGE) CAN OCCUR AROUND THE BENDING AREA.A CRACK WILL START TO FORM ON THE INSIDE OF THE HOSE AT THE AREA OF DEFORMATION.REGARDING UNLOADING STRESS, NISSAN STATES, AFTER THE CURING PROCESS, IN SOME INSTANCES THE HOSE STUCK TO THE MANDREL TIGHTLY AND THE OPERATOR HAD TO APPLY A SIGNIFICANT AMOUNT OF FORCE TO PULL THE HOSE FROM THE MANDREL.IF THIS OPERATION WAS PERFORMED ROUGHLY, THE INTERIOR OF THE HOSE COULD BE DAMAGED BY THE MANDREL EDGE. NISSAN ALSO STATES, BECAUSE OF THE WAY THE HOSES RECEIVED INTERNAL DAMAGE, A DAMAGED HOSE WAS PRODUCED AS A RARE, RANDOM EVENT RATHER THAN SYSTEMATICALLY.THE TRANSMISSION HOSE SUPPLIER, COOPER STANDARD AUTOMOTIVE, IMPLEMENTED PROCESS IMPROVEMENTS THAT LIMIT EXCESSIVE STRESS ON THE HOSE DURING MANUFACTURE. NISSAN HAS SHOWN THAT THIS TRANSMISSION COOLER HOSE WAS ASSEMBLED ON MY 2007 AND MY 2008 MAXIMA VEHICLES.NISSAN REDESIGNED THE TRANSMISSION COOLER HOSE ON MY 2009 MAXIMA, AND THE HOSE IS MANUFACTURED BY A NEW SUPPLIER.NISSAN HAS ALSO SHOWN THAT THE LEAKS MOSTLY OCCUR WITHIN THE FIRST 2000 MILES OF SERVICE WITH A SEVERE DROP IN INCIDENTS BEYOND 2000 MILES OF SERVICE.MOST LEAKS HAVE ALREADY OCCURRED, AND THE ONE FIRE WAS MINOR. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.
Additional source detail variants (2)
Power Train:automatic Transmission:cooling Unit And Lines
THIS PE WAS OPENED FOR MODEL YEAR (MY) 2008 NISSAN MAXIMA VEHICLES BASED ON EARLY WARNING DATA THAT THE AUTOMATIC TRANSMISSION COOLER HOSE MAY HAVE PINHOLES AND/OR CRACKS RESULTING IN A TRANSMISSION FLUID LEAK.THE LEAKED FLUID CAN CONTACT THE EXHAUST SYSTEM AND IGNITE.NISSAN HAS SHOWN THAT THE ROOT CAUSE OF THE PINHOLES AND/OR CRACKS IN THE HOSE IS EXCESSIVE STRESS DURING THE MANUFACTURE FORMING PROCESS RESULTING IN HOSE DEFORMATION AT LOADING ONTO A MANDREL, OR DAMAGE DURING UN-LOADING.REGARDING LOADING STRESS, NISSAN STATES, WHEN EXCESSIVE STRESS IS APPLIED WHILE LOADING THE HOSE ONTO THE MANDREL, HOSE DEFORMATION (WHICH LOOKS LIKE A BULGE) CAN OCCUR AROUND THE BENDING AREA.A CRACK WILL START TO FORM ON THE INSIDE OF THE HOSE AT THE AREA OF DEFORMATION.REGARDING UNLOADING STRESS, NISSAN STATES, AFTER THE CURING PROCESS, IN SOME INSTANCES THE HOSE STUCK TO THE MANDREL TIGHTLY AND THE OPERATOR HAD TO APPLY A SIGNIFICANT AMOUNT OF FORCE TO PULL THE HOSE FROM THE MANDREL.IF THIS OPERATION WAS PERFORMED ROUGHLY, THE INTERIOR OF THE HOSE COULD BE DAMAGED BY THE MANDREL EDGE. NISSAN ALSO STATES, BECAUSE OF THE WAY THE HOSES RECEIVED INTERNAL DAMAGE, A DAMAGED HOSE WAS PRODUCED AS A RARE, RANDOM EVENT RATHER THAN SYSTEMATICALLY.THE TRANSMISSION HOSE SUPPLIER, COOPER STANDARD AUTOMOTIVE, IMPLEMENTED PROCESS IMPROVEMENTS THAT LIMIT EXCESSIVE STRESS ON THE HOSE DURING MANUFACTURE. NISSAN HAS SHOWN THAT THIS TRANSMISSION COOLER HOSE WAS ASSEMBLED ON MY 2007 AND MY 2008 MAXIMA VEHICLES.NISSAN REDESIGNED THE TRANSMISSION COOLER HOSE ON MY 2009 MAXIMA, AND THE HOSE IS MANUFACTURED BY A NEW SUPPLIER.NISSAN HAS ALSO SHOWN THAT THE LEAKS MOSTLY OCCUR WITHIN THE FIRST 2000 MILES OF SERVICE WITH A SEVERE DROP IN INCIDENTS BEYOND 2000 MILES OF SERVICE.MOST LEAKS HAVE ALREADY OCCURRED, AND THE ONE FIRE WAS MINOR. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.
Power Train:automatic Transmission
THIS PE WAS OPENED FOR MODEL YEAR (MY) 2008 NISSAN MAXIMA VEHICLES BASED ON EARLY WARNING DATA THAT THE AUTOMATIC TRANSMISSION COOLER HOSE MAY HAVE PINHOLES AND/OR CRACKS RESULTING IN A TRANSMISSION FLUID LEAK.THE LEAKED FLUID CAN CONTACT THE EXHAUST SYSTEM AND IGNITE.NISSAN HAS SHOWN THAT THE ROOT CAUSE OF THE PINHOLES AND/OR CRACKS IN THE HOSE IS EXCESSIVE STRESS DURING THE MANUFACTURE FORMING PROCESS RESULTING IN HOSE DEFORMATION AT LOADING ONTO A MANDREL, OR DAMAGE DURING UN-LOADING.REGARDING LOADING STRESS, NISSAN STATES, WHEN EXCESSIVE STRESS IS APPLIED WHILE LOADING THE HOSE ONTO THE MANDREL, HOSE DEFORMATION (WHICH LOOKS LIKE A BULGE) CAN OCCUR AROUND THE BENDING AREA.A CRACK WILL START TO FORM ON THE INSIDE OF THE HOSE AT THE AREA OF DEFORMATION.REGARDING UNLOADING STRESS, NISSAN STATES, AFTER THE CURING PROCESS, IN SOME INSTANCES THE HOSE STUCK TO THE MANDREL TIGHTLY AND THE OPERATOR HAD TO APPLY A SIGNIFICANT AMOUNT OF FORCE TO PULL THE HOSE FROM THE MANDREL.IF THIS OPERATION WAS PERFORMED ROUGHLY, THE INTERIOR OF THE HOSE COULD BE DAMAGED BY THE MANDREL EDGE. NISSAN ALSO STATES, BECAUSE OF THE WAY THE HOSES RECEIVED INTERNAL DAMAGE, A DAMAGED HOSE WAS PRODUCED AS A RARE, RANDOM EVENT RATHER THAN SYSTEMATICALLY.THE TRANSMISSION HOSE SUPPLIER, COOPER STANDARD AUTOMOTIVE, IMPLEMENTED PROCESS IMPROVEMENTS THAT LIMIT EXCESSIVE STRESS ON THE HOSE DURING MANUFACTURE. NISSAN HAS SHOWN THAT THIS TRANSMISSION COOLER HOSE WAS ASSEMBLED ON MY 2007 AND MY 2008 MAXIMA VEHICLES.NISSAN REDESIGNED THE TRANSMISSION COOLER HOSE ON MY 2009 MAXIMA, AND THE HOSE IS MANUFACTURED BY A NEW SUPPLIER.NISSAN HAS ALSO SHOWN THAT THE LEAKS MOSTLY OCCUR WITHIN THE FIRST 2000 MILES OF SERVICE WITH A SEVERE DROP IN INCIDENTS BEYOND 2000 MILES OF SERVICE.MOST LEAKS HAVE ALREADY OCCURRED, AND THE ONE FIRE WAS MINOR. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.