TL* THE CONTACT OWNS A 1993 FORD F-250. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, HE NOTICED THAT THE SPEEDOMETER AND CRUISE CONTROL FAILED TO OPERATE. IN ADDITION, THE ABS WARNING INDICATOR ILLUMINATED ON THE INSTRUMENT PANEL. THE WARNING LIGHT REMAINED ILLUMINATED UNTIL THE ENGINE WAS TURNED OFF. THERE WAS A …
Read full complaint
TL* THE CONTACT OWNS A 1993 FORD F-250. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, HE NOTICED THAT THE SPEEDOMETER AND CRUISE CONTROL FAILED TO OPERATE. IN ADDITION, THE ABS WARNING INDICATOR ILLUMINATED ON THE INSTRUMENT PANEL. THE WARNING LIGHT REMAINED ILLUMINATED UNTIL THE ENGINE WAS TURNED OFF. THERE WAS A RECALL UNDER NHTSA CAMPAIGN ID NUMBER 8V051000 (VEHICLE SPEED CONTROL:CRUISE CONTROL) HOWEVER THE VIN WAS NOT INCLUDED. THE CONTACT EXPERIENCED THE SIMILAR DEFECT AS MENTIONED IN THE RECALL. THE VEHICLE WAS REPAIRED AT THE CONTACT'S EXPENSE. THE MANUFACTURER WAS MADE AWARE OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 145,000. UPDATED 10/17/12*LJ THE CONSUMER VIN WAS NOT INCLUDED IN THE RECALL. UPDATED 10/18/12
NHTSA ODI #10474130
Mileage unknown · Apr 18, 2008
Vehicle Speed Control
TL*THE CONTACT OWNS A 1993 FORD F250. THE VEHICLE WAS TAKEN TO THE DEALER FOR THE RECALL REPAIR REGARDING THE VEHICLE SPEED CONTROL: CRUISE CONTROL. THE DEALER DISCONNECTED THE CRUISE CONTROL ON OCTOBER 17, 2007 AND INFORMED THE CONTACT THAT THE REPLACEMENT PART WAS NOT YET AVAILABLE. THERE HAD BEEN NO FAILURE TO DATE. THE R…
Read full complaint
TL*THE CONTACT OWNS A 1993 FORD F250. THE VEHICLE WAS TAKEN TO THE DEALER FOR THE RECALL REPAIR REGARDING THE VEHICLE SPEED CONTROL: CRUISE CONTROL. THE DEALER DISCONNECTED THE CRUISE CONTROL ON OCTOBER 17, 2007 AND INFORMED THE CONTACT THAT THE REPLACEMENT PART WAS NOT YET AVAILABLE. THERE HAD BEEN NO FAILURE TO DATE. THE RECALL NUMBER AND PURCHASE DATE WERE UNKNOWN. THE CURRENT MILEAGE WAS 180,000.
NHTSA ODI #10224927
Mileage unknown · Mar 6, 2008
Vehicle Speed Control
TL*THE CONTACT OWNS A 1993 FORD F250. THE CONTACT RECEIVED A SAFETY RECALL NOTICE IN AUGUST OF 2007 FOR THE VEHICLE SPEED CONTROL. THE CRUISE CONTROL WAS DISCONNECTED AT THAT TIME. HE CALLED THEM AGAIN IN MARCH OF 2008 AND WAS INFORMED THAT THE PART WAS STILL UNAVAILABLE. HE WAS RECENTLY INFORMED THAT THE PART WOULD BE AVAIL…
Read full complaint
TL*THE CONTACT OWNS A 1993 FORD F250. THE CONTACT RECEIVED A SAFETY RECALL NOTICE IN AUGUST OF 2007 FOR THE VEHICLE SPEED CONTROL. THE CRUISE CONTROL WAS DISCONNECTED AT THAT TIME. HE CALLED THEM AGAIN IN MARCH OF 2008 AND WAS INFORMED THAT THE PART WAS STILL UNAVAILABLE. HE WAS RECENTLY INFORMED THAT THE PART WOULD BE AVAILABLE IN JUNE OF 2008. THERE HAD BEEN NO FAILURE TO DATE. THE CURRENT MILEAGE WAS 77,000. UPDATE 04-02-08 *BF
NHTSA ODI #10220233
Mileage unknown · Nov 9, 2000
Vehicle Speed Control
FIRST REPORTED DEFECT, CRUISE CONTROL. WHILE DRIVING ON 2 LANE AT CRUISE SPEED OF 40 MPH, ENTERED REDUCED SPEED ZONE, TAPPED BRAKES TO RELEASE CRUISE CONTROL AND SLOW TO 30 MPH, RELEASED BRAKE WHEN DESIRED SPEED WAS REACHED, VEHICLE SUDDENLY ACCELERATED, 2000 RPM ON TACH., RELEASED CRUISE WITH SWITCH ON STEERING WHEEL, FORD CUST…
Read full complaint
FIRST REPORTED DEFECT, CRUISE CONTROL. WHILE DRIVING ON 2 LANE AT CRUISE SPEED OF 40 MPH, ENTERED REDUCED SPEED ZONE, TAPPED BRAKES TO RELEASE CRUISE CONTROL AND SLOW TO 30 MPH, RELEASED BRAKE WHEN DESIRED SPEED WAS REACHED, VEHICLE SUDDENLY ACCELERATED, 2000 RPM ON TACH., RELEASED CRUISE WITH SWITCH ON STEERING WHEEL, FORD CUSTOMER SERVICE CONTACTED IN DETROIT, MI, STATED NO KNOWN RECALL, MY PROBLEM. SECOND ITEM NOTED, SINCE VEHICLE WAS PURCHASED, NEW, FRONT STEERING ASSEMBLY GREESE/DUST BOOTS HAVE SPLIT, DEALER REPLACED TWICE, ASKED TO DELAY THIRD REPLACEMENT UNTIL FORD COULD WORK OUT PROBLEM, WHEN RETURNED TO DEALER, UNDER NEW OWNERSHIP, TOLD TRUCK OUT OF WARRANTEE, PROBLEM WAS MINE, EVEN THOUGHT FORD FAILED TO EVER REPAIR. *AK
NHTSA ODI #736062
Mileage unknown · Feb 2, 1998
Electrical SystemEquipmentFuel System, Gasoline
FUEL INJECTOR FAILED.
NHTSA ODI #529557
Mileage unknown · Oct 21, 1996
Power TrainVehicle Speed Control
UNIVERSAL JOINT FAILED.
NHTSA ODI #510385
Mileage unknown · Mar 2, 1995
Vehicle Speed Control
UPON ACCELERATION TO PASS OTHER VEHICLE, GAS PEDAL STUCK IN DOWN POSITION. TT
NHTSA ODI #960941
Mileage unknown · Feb 15, 1995
Vehicle Speed Control
VEHICLE HAS SUDDEN UNWANTED ACCELERATION WHILE DRIVING. TT
FORD IS RECALLING 225,000 MY 1992-2003 ECONOLINE, MY 1993-1995 TAURUS SHO, MY 1992-1998 CROWN VICTORIA, MY 1993 BRONCO, F-SERIES, MY 1995-1997 F-SERIES SUPER DUTY STRIPPED CHASSIS, MY 1992-1998 MERCURY GRAND MARQUIS, AND MY 1992-1995 LINCOLN TOWN CAR VEHICLES. THE AFFECTED VEHICLES WERE PREVIOUSLY REPAIRED USING A WIRING HARNESS THAT IS NOT COMPATIBLE WITH THE VEHICLE CIRCUIT POLARITY.
Consequence & remedy
Consequence: AS A RESULT, THE FUSE IS LOCATED IN THE OUTPUT CIRCUIT RATHER THAN IN THE INTENDED INPUT POWER FEED CIRCUIT, AND MAY NOT OFFER THE INTENDED PROTECTION IN THE EVENT OF AN ELECTRICAL SHORT TO GROUND.
Remedy: DEALERS WILL INSTALL A NEW WIRING HARNESS, OR REPLACE THE MATING ELECTRICAL COMPONENT. THE RECALL BEGAN ON FEBRUARY 18, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.
Consequence & remedy
Consequence: THIS COULD RESULT IN AN UNDERHOOD FIRE.
Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.
VEHICLE DESCRIPTION: LIGHT DUTY TRUCKS AND CAB CHASSIS EQUIPPED WITH GASOLINE ENGINES AND DUAL FUEL TANKS. THE CARBON STEEL FUEL PRESSURE REGULATOR IN THE FUEL SYSTEM CAN WEAR OUT DURING THE LIFE OF THE VEHICLE. IF THE FUEL PRESSURE REGULATOR MALFUNCTIONS, IT CAN CAUSE HIGH FUEL SYSTEM PRESSURE, WHICH DAMAGES THE FUEL PUMP CHECK VALVE. THIS ALLOWS FUEL TO BE TRANSFERRED FROM ONE TANK TO THE OTHER, POSSIBLY OVERFILLING THE NON-OPERATING TANK, RESULTING IN FUEL OVERFLOW PAST THE FILLER CAP.
Consequence & remedy
Consequence: FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALERS WILL HAVE A STAINLESS STEEL FUEL PRESSURE REGULATOR INSTALLED. OWNER NOTIFICATION BEGAN JULY 9, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332. (SEE PREVIOUS NHTSA RECALL 93V-125/FORD RECALL 93S68).
THE PARKING BRAKE CONTROL SELF-ADJUST PAWL DOES NOT LINE UP PROPERLY WITH THE SELF-ADJUST RACHET CAUSING THE PAWL TO SLIP OVER ONE OR MORE TEETH IN THE RACHET.
Consequence & remedy
Consequence: WHEN THE ABOVE OCCURS, IT CAN RESULT IN PARKING BRAKE SYSTEM INEFFECTIVENESS. THE PARKING BRAKE WILL NOT HOLD THE VEHICLE, CAUSING THE VEHICLE TO ROLL FREELY, IF THE TRANSMISSION IS NOT LEFT IN GEAR.
Remedy: A WEDGE WILL BE INSTALLED WHICH WILL SERVE TO LOCK THE PARKING BRAKE SELF-ADJUST MECHANISM PAWL INTO ENGAGEMENT WITH THE RACHET. ALSO, OWNERS WILL BE ADVISED TO RELEASE AND REAPPLY THE PARKING BRAKE WHENEVER TOOTH SKIP OCCURS AND WILL BE REMINDED TO ALWAYS TURN OFF THE ENGINE AND LEAVE THE VEHICLE IN GEAR WHEN THE VEHICLE IS PARKED.
THE U-CLIP STYLE NUTS THAT RETAIN THE FRONT BUMPERS TO THE FRONT BUMPER INNER ARMS CAN FRACTURE.
Consequence & remedy
Consequence: IF ONE OF THE U-CLIP NUTS FRACTURES, THE BUMPER WILL LOOSEN AND RATTLE CAUSING FRACTURE OF THE REMAINING U-CLIP NUTS, RESULTING IN SEPARATION OF THE BUMPER FROM THE VEHICLE. IF THE BUMPER WERE TO DETACH FROM THE VEHICLE WHILE IT IS BEING DRIVEN, A VEHICLE COLLISION COULD RESULT.
Remedy: INSPECTION AND REPLACEMENT OF THE FOUR U-CLIP NUTS AND THE ASSOCIATED BOLTS.
A MALFUNCTIONING CHECK VALVE WITHIN THE FUEL PUMP ASSEMBLY CAUSES A PORTION OF THE UNUSED FUEL FROM ONE TANK TO BE RETURNED TO THE SECOND TANK. WHEN THIS OCCURS, THE CAPACITY OF THE SECOND TANK CAN BE EXCEEDED, CAUSING FUEL SPILLAGE.
Consequence & remedy
Consequence: SPILLED FUEL CAN RESULT IN A FIRE WHEN EXPOSED TO ASOURCE OF IGNITION.
Remedy: REPLACEMENT OF THE FUEL PRESSURE REGULATOR AND INSTALLATION OF REDUNDANT CHECK VALVES.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3
EA99032 · Dual Fuel Tank Crossflow/leakage
Opened Nov 4, 1999 · Closed Dec 6, 2001
Status: closed (inferred from source dates) · Vehicle Speed Control:linkages
ON JULY 14, 1993 FORD FILED A DEFECT INFORMATION REPORT CONCERNING FUEL TANK CROSS FLOW LEAKAGE ON F-SERIES LIGHT TRUCKS AND CAB CHASSIS BUILT FROM JULY 22, 1989 THROUGH DECEMBER 17, 1992.THE REMEDY WAS TO REPLACE THE FUEL PRESSURE REGULATOR AND INSTALL A CHECK VALVE BETWEEN EACH FUEL SUPPLY LINE AND FUEL TANK (2) TO REPAIR THE SUPPLY SIDE FUEL CROSS FLOW PROBLEM (RECALL 93V-125).ODI OPENED RQ98-008 ON MAY 29, 1998 BECAUSE OF THE LARGE NUMBER OF ALLEGED REMEDY FAILURES AND REPORTS OF FUEL CROSS FLOW ON VEHICLES OUTSIDE OF THE RECALL POPULATION.BASED ONTHE INFORMATION RECEIVED FROM FORD ON AUGUST 11, SEPTEMBER 30, AND DECEMBER 15, 1998, AND THE INCREASING TREND OF REMEDY FAILURES AND OUT OF SCOPE CROSSFLOW REPORTS, ODI OPENED EA99-032 ON NOVEMBER 4, 1999.THE ATTACHED ENGINEERING ANALYSIS CLOSING REPORT FULLY DESCRIBES THE RESULTS OF THIS INVESTIGATION AND REASON FOR CLOSING.THE SUBJECT VEHICLES CAN EXPERIENCE FUEL TRANSFER FROM ONE TANK TO THE OTHER DUE TO MALFUNCTIONS IN THE FUEL SYSTEM.WHEN FUEL IS PUMPED OR RETURNED TO THE NON-OPERATING TANK (CROSS FLOW), THE CAPACITY OF THE NON-OPERATING TANK CAN BE EXCEEDED, CAUSING FUEL TO OVERFLOW PAST THE FILLER CAP, CREATING A FIRE POTENTIAL.
Additional source detail variants (2)
Vehicle Speed Control:linkages
ON JULY 14, 1993 FORD FILED A DEFECT INFORMATION REPORT CONCERNING FUEL TANK CROSS FLOW LEAKAGE ON F-SERIES LIGHT TRUCKS AND CAB CHASSIS BUILT FROM JULY 22, 1989 THROUGH DECEMBER 17, 1992.THE REMEDY WAS TO REPLACE THE FUEL PRESSURE REGULATOR AND INSTALL A CHECK VALVE BETWEEN EACH FUEL SUPPLY LINE AND FUEL TANK (2) TO REPAIR THE SUPPLY SIDE FUEL CROSS FLOW PROBLEM (RECALL 93V-125).ODI OPENED RQ98-008 ON MAY 29, 1998 BECAUSE OF THE LARGE NUMBER OF ALLEGED REMEDY FAILURES AND REPORTS OF FUEL CROSS FLOW ON VEHICLES OUTSIDE OF THE RECALL POPULATION.BASED ONTHE INFORMATION RECEIVED FROM FORD ON AUGUST 11, SEPTEMBER 30, AND DECEMBER 15, 1998, AND THE INCREASING TREND OF REMEDY FAILURES AND OUT OF SCOPE CROSSFLOW REPORTS, ODI OPENED EA99-032 ON NOVEMBER 4, 1999.THE ATTACHED ENGINEERING ANALYSIS CLOSING REPORT FULLY DESCRIBES THE RESULTS OF THIS INVESTIGATION AND REASON FOR CLOSING.THE SUBJECT VEHICLES CAN EXPERIENCE FUEL TRANSFER FROM ONE TANK TO THE OTHER DUE TO MALFUNCTIONS IN THE FUEL SYSTEM.WHEN FUEL IS PUMPED OR RETURNED TO THE NON-OPERATING TANK (CROSS FLOW), THE CAPACITY OF THE NON-OPERATING TANK CAN BE EXCEEDED, CAUSING FUEL TO OVERFLOW PAST THE FILLER CAP, CREATING A FIRE POTENTIAL.
Vehicle Speed Control:linkages
ON JULY 14, 1993 FORD FILED A DEFECT INFORMATION REPORT CONCERNING FUEL TANK CROSS FLOW LEAKAGE ON F-SERIES LIGHT TRUCKS AND CAB CHASSIS BUILT FROM JULY 22, 1989 THROUGH DECEMBER 17, 1992.THE REMEDY WAS TO REPLACE THE FUEL PRESSURE REGULATOR AND INSTALL A CHECK VALVE BETWEEN EACH FUEL SUPPLY LINE AND FUEL TANK (2) TO REPAIR THE SUPPLY SIDE FUEL CROSS FLOW PROBLEM (RECALL 93V-125).ODI OPENED RQ98-008 ON MAY 29, 1998 BECAUSE OF THE LARGE NUMBER OF ALLEGED REMEDY FAILURES AND REPORTS OF FUEL CROSS FLOW ON VEHICLES OUTSIDE OF THE RECALL POPULATION.BASED ONTHE INFORMATION RECEIVED FROM FORD ON AUGUST 11, SEPTEMBER 30, AND DECEMBER 15, 1998, AND THE INCREASING TREND OF REMEDY FAILURES AND OUT OF SCOPE CROSSFLOW REPORTS, ODI OPENED EA99-032 ON NOVEMBER 4, 1999.THE ATTACHED ENGINEERING ANALYSIS CLOSING REPORT FULLY DESCRIBES THE RESULTS OF THIS INVESTIGATION AND REASON FOR CLOSING.THE SUBJECT VEHICLES CAN EXPERIENCE FUEL TRANSFER FROM ONE TANK TO THE OTHER DUE TO MALFUNCTIONS IN THE FUEL SYSTEM.WHEN FUEL IS PUMPED OR RETURNED TO THE NON-OPERATING TANK (CROSS FLOW), THE CAPACITY OF THE NON-OPERATING TANK CAN BE EXCEEDED, CAUSING FUEL TO OVERFLOW PAST THE FILLER CAP, CREATING A FIRE POTENTIAL.
EA95012 · Failure Of Serpentine Belt
Opened Mar 31, 1995 · Closed May 28, 1996
Status: closed (inferred from source dates) · Power Train
AN ENGINEERING ANALYSIS CLOSING REPORT IS INCLUDED.
Additional source detail variants (2)
Power Train
AN ENGINEERING ANALYSIS CLOSING REPORT IS INCLUDED.
Power Train
AN ENGINEERING ANALYSIS CLOSING REPORT IS INCLUDED.
EA93020 · Parking Brake Failure
Opened Jul 28, 1993 · Closed Sep 23, 1994
Status: closed (inferred from source dates) · Service Brakes, Hydraulic
There is no summary currently available
Additional source detail variants (2)
Service Brakes, Hydraulic
There is no summary currently available
Service Brakes, Hydraulic
There is no summary currently available
1993 Ford F-250 Problems, Complaints & Recalls | Skip That Year
Illustration