IllustrationMy Brake Vacuum Pump is broken, with oil leaking into the vacuum reservoir. The brake distance is much longer. I searched the web and found out a lot of people had the same issue.
2013 BMW X3
Owner reports · Recalls · Investigations
More warning signs than most X3 years
Owner complaints for the 2013 BMW X3 are substantially higher than the model-year median of 86.
About this comparison →How this year compares
Owner complaints by model year
Compare all X3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
170–25K
1325–50K
2850–75K
6675–100K
35100–150K
2150K+
161 reports with mileage · 65 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 147 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 60 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 29 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports10 fire reports4 injury reports
Service Brakes complaints
17 reportsWhen driving and after using brakes, the brakes do not let off, they drag. I was driving on the highway, and had to slow down for traffic and the car would not accelerate.This happened several times and I brought it to a BMW repair shop. They diagnosed it to be the ABS pump, replaced it with a used one and I have not had any pro…
Read full complaint
When driving and after using brakes, the brakes do not let off, they drag. I was driving on the highway, and had to slow down for traffic and the car would not accelerate.This happened several times and I brought it to a BMW repair shop. They diagnosed it to be the ABS pump, replaced it with a used one and I have not had any problems since. I have researched this issue and found others with like make & model have had similar problems. Since this could cause the vehicle to slow down without actually braking, I worry about someone hitting the car from the back because the brake lights don't come on when this happens.
WHILE DRIVING DOWN BUSINESS 40 GOING ABOUT 60 MPH, MY CAR SUDDENLY STOPPED IN THE LEFT LANE. THE CAR WAS STILL RUNNING BUT IT WAS AS IF SOMEONE HAD PUT ON THE BRAKES FOR ME -- LIKE A GHOST IN THE MACHINE. THE CAR BEHIND ME WAS ABLE TO STOP BUT WITHIN A COUPLE OF FEET FROM REAR ENDING ME AT A HIGH SPEED. THE CARS BEHIND HIM WE…
Read full complaint
WHILE DRIVING DOWN BUSINESS 40 GOING ABOUT 60 MPH, MY CAR SUDDENLY STOPPED IN THE LEFT LANE. THE CAR WAS STILL RUNNING BUT IT WAS AS IF SOMEONE HAD PUT ON THE BRAKES FOR ME -- LIKE A GHOST IN THE MACHINE. THE CAR BEHIND ME WAS ABLE TO STOP BUT WITHIN A COUPLE OF FEET FROM REAR ENDING ME AT A HIGH SPEED. THE CARS BEHIND HIM WERE SWERVING NOT TO HIT HIM. WE ARE LUCKY IT WAS NOT A MULTI CAR ACCIDENT. I WAS ABLE TO GET THE CAR GOING BY CONTINUING TO STEP ON THE ACCELERATOR. NO LIGHTS ON THE DASH CAME ON NOT EVEN A CHECK ENGINE LIGHT. I THOUGHT THAT PERHAPS I HAD DONE SOMETHING TO CAUSE THIS AND KEPT DRIVING IN THE RIGHT LANE AT A LOWER SPEED. THEN IT HAPPENED AGAIN. LUCKILY NO ONE WAS CLOSE BEHIND ME AND THIS TIME I KNEW WHAT WAS HAPPENING. I PULLED OVER AND PUT ON MY HAZARDS AND DROVE ON THE SHOULDER. THE CAR WAS SPUTTERING, THE WHEEL WAS SHAKING. I PULLED OVER AND TURNED OFF THE CAR. LET IT REST AND INSPECTED THE OUTSIDE OF THE CAR. I WENT THE NEXT DAY TO THE BMW DEALERSHIP -- THEY SAID TO REPLACE THE BRAKE CALIPERS BUT I DID NOT THING THAT WAS IT --- AS IT SEEMS ALMOST LIKE A FORCE ENGAGED THE BRAKES, NOT THAT THEY FAILED. MY FOOT HAD NOT BEEN ON THE BRAKES WHEN THEY ENGAGED. I TOOK IT TO ANOTHER MECHANIC WHO WAS ABLE TO REPLICATE THIS AND SAID THE CAR WAS UNSAFE TO DRIVE. I AM ONLY THE 2ND OWNER AND IT HAS LESS THAN 50K MILES. I THEN HAD IT INSPECTED AT A DIFFERENT DEALERSHIP WHO SAID IT WAS THE DSC WHICH SEEMS MORE LIKELY AS THEY WERE ABLE TO RECREATE THE BRAKING WHILE DRIVING. I THEN CALLED BMW NA WHO SENT OUT AND ENGINEER BUT THEY ARE SAYING IT IS REGULAR WEAR AND TEAR ON A CAR. THIS SEEMS IMPOSSIBLE TO ME. I HAVE HAD BRAKES NEED REPLACING AND ROTORS AND NOTHING LIKE THIS HAS EVER HAPPENED. IT WAS INCREDIBLY SCARY, AND DANGEROUS AND I (AND OTHERS) COULD HAVE BEEN SERIOUSLY INJURED.
AUGUST 10, 2020. I WAS DRIVING TO THE STORE ABUT 10 MILES FROM HOME ON A MAJOR HIGHWAY AND MY 2013 BMW X328I, SUDDENLY STARTED TO GO CRAZY IN A MANNER THAT I NEVER EXPERIENCED BEFORE A LOT OF LIGHTS SUCH AS, (ENGINE, ABS, DSC, DTC, BRAKES,POWERTRAIN, AND STIMULATION. THE VEHICLE BECAME NON-DRIVABLE AND A SAFETY HAZARDOUS IN NATU…
Read full complaint
AUGUST 10, 2020. I WAS DRIVING TO THE STORE ABUT 10 MILES FROM HOME ON A MAJOR HIGHWAY AND MY 2013 BMW X328I, SUDDENLY STARTED TO GO CRAZY IN A MANNER THAT I NEVER EXPERIENCED BEFORE A LOT OF LIGHTS SUCH AS, (ENGINE, ABS, DSC, DTC, BRAKES,POWERTRAIN, AND STIMULATION. THE VEHICLE BECAME NON-DRIVABLE AND A SAFETY HAZARDOUS IN NATURE THAT IT ALMOST CAUSE AN ACCIDENT. I ACT IN A EMERGENCY STATE OF MIND AND WAS ABLE TO PULL INTO A NEARBY PARKING LOT AT 15315 MERRY CAT LN, BELLE HAVEN, VA 23306. I PROCEEDED IN CALLING THE AAA TOWING COMPANY TO TAKE THE VEHICLE TO MY PLACE OF RESIDENT. *DT *TR
ON AUGUST 1ST, WE EXPERIENCED A DANGEROUS SITUATION ON THE HIGHWAY; THE VEHICLE SLOWED DOWN IN TRAFFIC, HARD JERKING, SMELLED OF BURNING FUEL OR FUMES. WE THEN TOOK IT TO THE BMW DEALERSHIP IN TALLAHASSEE WHICH WAS TWO DAYS AFTER THE INCIDENT. AFTER THEY DID A DIAGNOSTIC ON IT, WE WERE TOLD IT WAS A MECHANICAL FAILURE WITHIN THE…
Read full complaint
ON AUGUST 1ST, WE EXPERIENCED A DANGEROUS SITUATION ON THE HIGHWAY; THE VEHICLE SLOWED DOWN IN TRAFFIC, HARD JERKING, SMELLED OF BURNING FUEL OR FUMES. WE THEN TOOK IT TO THE BMW DEALERSHIP IN TALLAHASSEE WHICH WAS TWO DAYS AFTER THE INCIDENT. AFTER THEY DID A DIAGNOSTIC ON IT, WE WERE TOLD IT WAS A MECHANICAL FAILURE WITHIN THE BRAKE SYSTEM AND AFTER THEY EXAMINED IT AND TOOK IT FOR A TEST DRIVE, THE BRAKES ON BOTH SIDES BECAME EXTREMELY HOT WITH EXTREME HEAT AND SMOKING FROM BOTH BRAKES. THEY EXPLAINED THE EXPERIENCE WAS VERY UNUSUAL AND COULD HAVE CAUSED DANGEROUS RESULTS ON THE ROAD. WE WERE TOLD IT WASN'T IN OUR BEST INTERESTS NOT TO ATTEMPT TO DRIVE IT MORE THAN 2 MILES. WE HAD NO CHOICE BUT TO LEAVE IT ACROSS THE STREET WITH CARMAX, THE LIEN HOLDER. EVEN THOUGH IT IS A MANUFACTURER'S ISSUE THE BMW DEALERSHIP WOULDN'T HELP US UNLESS WE PAID NEARLY 5K OUT OF POCKET. CARMAX ALSO WOULDN'T HELP UNLESS WE AGREED TO PAY THEM AS WELL. WE ARE OUT OF A MAJOR LOSS CONSIDERING IT'S WAS DEFECTED BY THE MANUFACTURER AND WE'VE ONLY HAD THE CAR 2 YEARS. WE WERE TOLD WE WERE LUCKY AND THAT THE TIRES WOULD HAVE CAUGHT ON FIRE ON THE ROAD.! WE WOULD APPRECIATE YOUR FULL INVESTIGATION INTO THIS MATTER; WE ARE NOT FINANCIALLY STABLE TO INCUR SUCH A FINANCIAL LOSS AS WELL AS LOSING THE VEHICLE. THANKS
THE BRAKES ARE LESS OR NOT RESPONSIVE IN CITY DRIVE. I NOTIFIED 3 TIMES TO DEALER BUT THEY SAID NO PROBLEM WITH THE BRAKES. IT MUST BE SOMETHING WRONG IN ELECTRONICS. ALOT OF OTHER OWNERS OF 2013 BMW X3 HAVE SAME COMPLAINT. IT IS VERY RISKY. IT HAPPENED 3 OUT OF 4 TIMES WHIKE DRIVING IN 35 MPH LIMITS. THOUGH THE BRAKES FEEL GOOD…
Read full complaint
THE BRAKES ARE LESS OR NOT RESPONSIVE IN CITY DRIVE. I NOTIFIED 3 TIMES TO DEALER BUT THEY SAID NO PROBLEM WITH THE BRAKES. IT MUST BE SOMETHING WRONG IN ELECTRONICS. ALOT OF OTHER OWNERS OF 2013 BMW X3 HAVE SAME COMPLAINT. IT IS VERY RISKY. IT HAPPENED 3 OUT OF 4 TIMES WHIKE DRIVING IN 35 MPH LIMITS. THOUGH THE BRAKES FEEL GOOD AT HIGH SPEED OR HIGHWAY LIMITS
2013 BMW X3. CONSUMER WRITES IN REGARDS TO VEHICLE BRAKE REPAIRS NOT COVERED UNDER EXTENDED WARRANTY. *LD *JS
LAST WEEK WHEN IN CITY TRAFFIC, I DEPRESSED THE BRAKE TO SLOW DOWN, THEN LIFTED MY FOOT OFF THE BRAKE. MY CAR LURCHED FORWARD AND I IMMEDIATELY BRAKED AGAIN TO SLOW DOWN AND STOP. THIS WAS NOT NORMAL, HAD NOT HAPPENED BEFORE, AND I DECIDED TO MENTION IT DURING MY NEXT VISIT TO BMW SERVICE. LAST SATURDAY, FEB. 17, I WAS DRIVING …
Read full complaint
LAST WEEK WHEN IN CITY TRAFFIC, I DEPRESSED THE BRAKE TO SLOW DOWN, THEN LIFTED MY FOOT OFF THE BRAKE. MY CAR LURCHED FORWARD AND I IMMEDIATELY BRAKED AGAIN TO SLOW DOWN AND STOP. THIS WAS NOT NORMAL, HAD NOT HAPPENED BEFORE, AND I DECIDED TO MENTION IT DURING MY NEXT VISIT TO BMW SERVICE. LAST SATURDAY, FEB. 17, I WAS DRIVING 20 -25 MPH IN A NEIGHBORHOOD, APPROACHING A RED LIGHT ON RIVER RD, BETHESDA. THERE WAS ONE CAR AT THE LIGHT. I BRAKED TO SLOW DOWN, AND REALIZED THAT THE CAR WAS NOT SLOWING DOWN, BRAKED AGAIN AND IT LURCHED FORWARD AND ACCELERATED. I SAW THE SPEED THE SPEEDOMETER MOVING BETWEEN 20-25, AND THE TACHOMETER VARYING WILDLY BETWEEN 1.5 - 2.5. I PRESSED VERY HARD ON THE BRAKE, WHICH WAS HARDER TO PRESS DOWN THAN EVER BEFORE, PRESSED THE PARK BUTTON AND FINALLY GOT THE CAR TO GO INTO PARK BEFORE I ARRIVED AT THE STOPPED VEHICLE IN FRONT OF ME. THIS ALL HAPPENED IN LESS THAN 10 SECONDS. I IMMEDIATELY CALLED BMW AND TOOK MY CAR IN, EXPLAINING WHAT HAPPENED, STILL VERY SHAKEN AND AFRAID TO DRIVE THE CAR. AFTERWARDS, I LOOKED ON THE INTERNET, AND READ ABOUT OTHER 2013 X3 DRIVERS WITH THE SAME EXPERIENCE. IT DID NOT APPEAR THAT BMW WAS ABLE TO REPLICATE THE PROBLEM OR THAT THEY REPAIRED THE CARS TO FIX THE PROBLEM. ONE PERSON DID HAVE AN ACCIDENT AND TOTALED THE CAR. THUS FAR, BMW HAS TOLD ME THEY CANNOT REPLICATE THE PROBLEM. I REQUESTED THE SERVICE MANAGER TO GET INVOLVED AND WILL ASK TO SPEAK TO THE FACTORY REP AS WELL. THIS IS A MAJOR SAFETY HAZARD PUTTING MY LIFE AND OTHERS AT RISK. IT IS NOT SAFE TO DRIVE MY CAR. I WOULD LIKE TO KNOW HOW MANY SIMILAR COMPLAINTS HAVE BEEN FILED WITH NHTSA AND WHAT NHTSA HAS DONE TO ADDRESS THIS SERIOUS SAFETY FLAW.
THE BRAKING SYSTEM HAS STOPPED WORK AND ALMOST CAUSED A CRASH. THE BRAKE GUILD AND BRAKE PADS ALL CHECK OK BUT VACUUM HAS BEEN LOST TO THE BOOSTER. YOU CAN HERE THE CAM MAKING NOISE WHEN YOU START THE VEHICLE AND THE NOISE HAS BEEN SINCE WE PURCHASED IT AND BMW STATES THAT'S NORMAL. I FEEL LIKE THE RECALL REPAIR WAS NOT DONE COR…
Read full complaint
THE BRAKING SYSTEM HAS STOPPED WORK AND ALMOST CAUSED A CRASH. THE BRAKE GUILD AND BRAKE PADS ALL CHECK OK BUT VACUUM HAS BEEN LOST TO THE BOOSTER. YOU CAN HERE THE CAM MAKING NOISE WHEN YOU START THE VEHICLE AND THE NOISE HAS BEEN SINCE WE PURCHASED IT AND BMW STATES THAT'S NORMAL. I FEEL LIKE THE RECALL REPAIR WAS NOT DONE CORRECTLY. ALSO THERE SEEM TO BE A DRIVE TRAIN MALFUNCTION THAT BMW CAN NOT FIGURE OUT. PLEASE HELP
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE DRIVING APPROXIMATELY 60 MPH, THE BRAKE PEDAL WAS DEPRESSED BUT THE VEHICLE HESITATED TO STOP. THE VEHICLE WAS TAKEN TO A DEALER FOR DIAGNOSTIC TESTING. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 13V454000 (SERVICE BRAKES, HYDRAULIC); HOWEVER, THE PARTS WERE UNAVAILABLE …
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE DRIVING APPROXIMATELY 60 MPH, THE BRAKE PEDAL WAS DEPRESSED BUT THE VEHICLE HESITATED TO STOP. THE VEHICLE WAS TAKEN TO A DEALER FOR DIAGNOSTIC TESTING. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 13V454000 (SERVICE BRAKES, HYDRAULIC); HOWEVER, THE PARTS WERE UNAVAILABLE TO PERFORM THE REPAIRS. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 3,000.
Official recalls
724V608000 · Electrical System:wiring:connectors/plugs/receptacles; Engine And Engine Cooling:cooling System:pump
Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
24V527000 · Air Bags:frontal:driver Side:inflator Module
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
17V495000 · Air Bags:frontal:driver Side:inflator Module
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
16V333000 · Child Seat:latch Strap
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
14V627000 · Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
13V570000 · Air Bags; Electrical System: Instrument Cluster/panel
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
13V454000 · Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.