IllustrationMy Brake Vacuum Pump is broken, with oil leaking into the vacuum reservoir. The brake distance is much longer. I searched the web and found out a lot of people had the same issue.
2013 BMW X3
Owner reports · Recalls · Investigations
More warning signs than most X3 years
Owner complaints for the 2013 BMW X3 are substantially higher than the model-year median of 86.
About this comparison →How this year compares
Owner complaints by model year
Compare all X3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
170–25K
1325–50K
2850–75K
6675–100K
35100–150K
2150K+
161 reports with mileage · 65 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 147 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 60 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 29 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports10 fire reports4 injury reports
What owners actually said
226 reportsThe contact owns a 2013 BMW X3. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power with the check engine warning light and drivetrain warning light illuminated. The vehicle failed to restart and was towed to the dealer. The dealer diagnosed that the positive battery terminal motherboard …
Read full complaint
The contact owns a 2013 BMW X3. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power with the check engine warning light and drivetrain warning light illuminated. The vehicle failed to restart and was towed to the dealer. The dealer diagnosed that the positive battery terminal motherboard had failed and needed to be replaced. The vehicle was repaired; however, the failure recurred. The vehicle was later towed to an independent mechanic, where it was diagnosed that the engine had failed and needed to be replaced. The vehicle was not repaired. The dealer was not contacted again. The manufacturer was made aware of the failure. The approximate failure mileage was 106,000.
BMW knows there is a problem with the 2013 x3 timing chain. I have continuously had my BMW serviced at there shops. Never once when my car was in for service did they mention the issue or proactively check. My vehicle now has the issue per the dealership snd indicated it is approximately a 20k repair which they included a ne…
Read full complaint
BMW knows there is a problem with the 2013 x3 timing chain. I have continuously had my BMW serviced at there shops. Never once when my car was in for service did they mention the issue or proactively check. My vehicle now has the issue per the dealership snd indicated it is approximately a 20k repair which they included a new engine. I also followed BMWs recommendation to have the oil changed 1year or when miles were hit per their change program. Just has the oil changed in November and at the end of December now timing chain issues. Again multiple times this issue could have been identified and proactively fixed while under warrenty. Also has issues where the material on the glove box peeled off. BMW is also aware of this issue. Poor design and quality on these models/engine. Thank goodness i was not on the expressway when drivabilty issuev occurred!!!
The contact's daughter owns a 2013 BMW X3. The contact stated that the vehicle was included in NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The contact took the vehicle to the dealer for the recall repair; however, the dealer found no signs of contamination and installed a water pump connector…
Read full complaint
The contact's daughter owns a 2013 BMW X3. The contact stated that the vehicle was included in NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The contact took the vehicle to the dealer for the recall repair; however, the dealer found no signs of contamination and installed a water pump connector cap. The contact stated that a month after the repair, the engine was overheating while idling, and there was while smoke coming from the engine with an unknown warning light on the instrument panel. Due to the failure, the vehicle was towed to an independent mechanic, where the water pump and the battery were replaced. The mechanic informed the contact that the water pump connector cap was faulty and had caused the failure. The contact was reminded by his wife of the water pump recall and that the connector cap was replaced due to the recall. Despite the repair, the vehicle shut off soon after starting the vehicle. Due to the failure, the vehicle was towed to a BMW specialist, who discovered that an antifreeze leak had caused corrosion of several electrical wires inside the engine. The specialist informed the contact that the vehicle needed two engine wiring harnesses, an engine computer, and an IVM (Integrated Supply Module). The manufacturer was notified of the failure, and the contact filed paperwork online to be reimbursed for the repairs made to the vehicle. The manufacturer denied the reimbursement because the vehicle had been serviced by an independent mechanic and not a dealer. The vehicle was not repaired. The failure mileage was approximately 100,000.
While driving my 2013 BMW X3 xDrive28i under normal conditions, a “drivetrain malfunction” warning suddenly appeared, immediately followed by a “low oil pressure” warning. Within seconds, the engine lost all power and shut off completely while the vehicle was in motion. I had to coast and steer the car off the roadway and push i…
Read full complaint
While driving my 2013 BMW X3 xDrive28i under normal conditions, a “drivetrain malfunction” warning suddenly appeared, immediately followed by a “low oil pressure” warning. Within seconds, the engine lost all power and shut off completely while the vehicle was in motion. I had to coast and steer the car off the roadway and push it to safety with the help of others. My safety and the safety of other drivers were at risk due to the sudden and complete loss of propulsion in active traffic. An independent BMW-trained service center confirmed that the engine suffered catastrophic internal damage caused by failure of the timing chain system. This timing chain defect is well documented in BMW’s N20 engines and is the subject of a class action lawsuit. The vehicle is now completely undriveable and remains at the repair facility. Engine replacement is the only option and is estimated between $12,000–$15,000, far exceeding the value of the vehicle. The failed engine and vehicle are available for inspection upon request. The problem has been reproduced and confirmed by an independent BMW specialist. BMW has not yet inspected the vehicle, although I did call and report to BMW North America. They have not responded to my numerous calls and outreach. No police or insurance representatives have inspected it because there was no collision, just sudden engine failure. There were no symptoms before the incident. The drivetrain and oil pressure warnings appeared only moments before the engine shut down. I had no opportunity to safely exit traffic before the vehicle lost power completely. This sudden failure due to a known engine defect presents a significant safety concern.
The car experienced major issues and nearly stalled while driving. It was pulled off a road into a driveway where it caught fire and burned to the ground. No recall information was ever sent to my house. Very dangerous occurrence. We are lucky that no one was hurt.
I own a 2013 BMW X3 equipped with the N20 engine. After approximately 17 months of ownership and only around 11,000 miles of normal driving, the vehicle suffered a sudden and complete engine failure without warning. The independent diagnostic determined the failure was due to a timing chain and oil pump drive chain defect, which…
Read full complaint
I own a 2013 BMW X3 equipped with the N20 engine. After approximately 17 months of ownership and only around 11,000 miles of normal driving, the vehicle suffered a sudden and complete engine failure without warning. The independent diagnostic determined the failure was due to a timing chain and oil pump drive chain defect, which is a well-documented issue in BMW N20 engines. This defect has been acknowledged by BMW through Technical Service Bulletin SI B11 03 17 and the national class action settlement Bang v. BMW of North America. The defect causes premature wear and eventual breakage of the timing chain components, resulting in catastrophic engine damage. My vehicle is now inoperable, and the cost to repair exceeds $7,500 — far more than the vehicle’s value. There were no prior warning lights, noises, or messages. This sudden engine failure creates a safety risk, as the vehicle could lose power unexpectedly while driving. No authorized BMW dealer had ever performed timing chain replacement on this vehicle, and the issue was not disclosed at the time of sale. I am filing this complaint so NHTSA is aware of the widespread nature and serious safety implications of this defect.
The contact owns a 2013 BMW X3. The contact stated that after starting the vehicle, smoke was noticed leaking from under the hood. The contact stated that after she opened the hood, the vehicle caught on fire. No warning lights were illuminated. In addition, the contact stated that she and a neighbor had extinguished the fire ut…
Read full complaint
The contact owns a 2013 BMW X3. The contact stated that after starting the vehicle, smoke was noticed leaking from under the hood. The contact stated that after she opened the hood, the vehicle caught on fire. No warning lights were illuminated. In addition, the contact stated that she and a neighbor had extinguished the fire utilizing a fire extinguisher. No police report was filed. The fire department did not arrive on scene. The vehicle was not towed. The vehicle was not deemed a total loss. The contact was burned on her hand however, she did not seek medical attention. Upon further inspection, the contact noticed that spark plug wires and other unknown parts were burned. The contact stated that the vehicle was previously seen by a local dealer for recall repair; however, the vehicle was not diagnosed with any recall-related failures and was diagnosed as needing a timing change replacement. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The contact received a notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The manufacturer was made aware of the failure. The failure mileage was approximately 160,000.
I am submitting this report to highlight a serious safety defect involving premature timing chain failures in BMW vehicles. The case relates to a 2013 BMW X3, but the problem is widely documented across multiple BMW models from this production era. The timing chain is intended to last the lifetime of the engine. If it stretches…
Read full complaint
I am submitting this report to highlight a serious safety defect involving premature timing chain failures in BMW vehicles. The case relates to a 2013 BMW X3, but the problem is widely documented across multiple BMW models from this production era. The timing chain is intended to last the lifetime of the engine. If it stretches, loosens, or fails, the engine can shut down immediately, causing sudden loss of power steering, power brakes, and overall control of the vehicle. This creates an extreme risk of accidents at highway speeds or in traffic. Unlike tires or brakes, this is not a normal wear component and should not fail under ordinary driving conditions. In this vehicle, the timing chain issue was identified at under 72,000 miles. A timing chain should last well over 400,000 miles under normal operation. The premature failure reflects a design flaw, not normal aging or maintenance. The vehicle had recently undergone major servicing at a BMW authorized dealer. At that time, the timing belt and other components were replaced at significant cost. The dealership did not disclose any timing chain concerns during that service. Only shortly afterward, during a recall-related visit, did they report that the timing chain required replacement, with a repair estimate of several thousand dollars. This matter was raised with BMW of North America, including a direct letter to its CEO. BMW acknowledged receipt but declined to take responsibility, treating the matter as outside warranty coverage rather than as a safety defect. The timing chain issue is widely reported, and BMW is aware of it. The sudden engine failure that can result from this defect presents a major safety hazard that warrants NHTSA’s attention.
The contact owns a 2013 BMW X3. The contact stated that while operating the vehicle, there was smoke coming from under the hood of the vehicle, and there was oil leaking from the engine compartment. The vehicle was taken to the local dealer who diagnosed the vehicle and determined that the engine gasket was faulty and needed to …
Read full complaint
The contact owns a 2013 BMW X3. The contact stated that while operating the vehicle, there was smoke coming from under the hood of the vehicle, and there was oil leaking from the engine compartment. The vehicle was taken to the local dealer who diagnosed the vehicle and determined that the engine gasket was faulty and needed to be replaced. Additionally, the contact was informed that the subframe of the vehicle was rusted. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 134,000.
Official recalls
724V608000 · Electrical System:wiring:connectors/plugs/receptacles; Engine And Engine Cooling:cooling System:pump
Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
24V527000 · Air Bags:frontal:driver Side:inflator Module
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
17V495000 · Air Bags:frontal:driver Side:inflator Module
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
16V333000 · Child Seat:latch Strap
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
14V627000 · Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
13V570000 · Air Bags; Electrical System: Instrument Cluster/panel
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
13V454000 · Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.