NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
42 reportsMileage unknown · Mar 27, 2026
Power Train
Over about seven years and roughly 70,000 miles of ownership, this 2012 BMW X3 generated repeated “Drivetrain malfunction” warnings and loss of drivability despite extensive repairs by multiple authorized BMW dealers. I paid approximately $15,000–$20,000 out of pocket for dealer repairs, and my third‑party service contract (CarS…
Read full complaint
Over about seven years and roughly 70,000 miles of ownership, this 2012 BMW X3 generated repeated “Drivetrain malfunction” warnings and loss of drivability despite extensive repairs by multiple authorized BMW dealers. I paid approximately $15,000–$20,000 out of pocket for dealer repairs, and my third‑party service contract (CarShield) paid an additional roughly $15,000–$20,000 directly to these BMW dealers during this period. In December 2025, an authorized BMW dealer diagnosed a drivetrain malfunction as failure of the fuel pump control module, allegedly caused by a small water spill on the rear seat, charged me $1,690.71 to replace the module, and returned the vehicle as repaired. Shortly afterward, while driving normally, the same “Drivetrain malfunction” warning reappeared, and drivability issues returned, indicating the defect was not corrected and raising serious concerns about the safety and reliability of the drivetrain and related electronic controls. The dealer’s attribution of the failure to minor interior water exposure also caused the service‑contract administrator to void coverage for the fuel system, leaving me with this large repair bill for an unresolved safety‑related condition that ultimately forced me to dispose of the vehicle at a significant loss.
NHTSA ODI #11727392
Mileage unknown · Dec 21, 2024
Air Bags
Front passenger seat occupancy mat defect causes disabling of passenger airbag. Recalls have been issued for the same issue in other models. Issue confirmed by dealership. Persistent warning lamp alert.
NHTSA ODI #11631946
Mileage unknown · Jun 2, 2024
EngineService BrakesVehicle Speed Control
I emailed BMW of Arlington on [XXX] detailing the critical safety issue I experienced with my BMW X3 2012 on Sunday [XXX]. I was driving on the tollway northbound from [XXX] in Grand Prairie in the pouring rain with my wipers on, and the car suddenly started braking and decelerating from the 70 mph cruising speed to 40 mph in se…
Read full complaint
I emailed BMW of Arlington on [XXX] detailing the critical safety issue I experienced with my BMW X3 2012 on Sunday [XXX]. I was driving on the tollway northbound from [XXX] in Grand Prairie in the pouring rain with my wipers on, and the car suddenly started braking and decelerating from the 70 mph cruising speed to 40 mph in seconds. The car behind me nearly hit my vehicle, and since it kept doing that, I had to turn on my hazard lights till I exited. The car was doing that irrespective of whether it was on cruise control or my driving speed. I discovered by googling it that this is a known defect in BMWs since their shop foremen and certified technicians who know more than me think I am dreaming this up [XXX] -. Driving this car on the highways in Dallas regularly is extremely dangerous as I could end up in a major multivehicle MVA pileup. Also, the previous time I had this issue before I brought it in on [XXX], it wasn't raining, and it started with the car not even moving when I put it in reverse and pressed the gas. Then it suddenly started decelerating on the road, backfired, and shook violently at normal speeds. The car overheated as the radiator coolant leaked, and I had to replenish it. CarShield, the Auto Warranty company, and I paid approximately $7,000 to BMW Mini of Arlington between June 2023 and today (see attached invoices_receipts_diagnosis reports). The last two times ([XXX] and [XXX]), their multi-point diagnosis on my vehicle identified no issues that need attention. Two of their service advisors who worked on my car in June and October 2023 quit immediately after completing it. The dealership does not respond to the BBB or my calls, emails, faxes, etc. BMW USA advised me to contact NHTSA. On June [XXX], while driving on city streets, the brakes were squealing even without engaging, and the car overheated/ backfired again/ almost caught fire. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6) The dealer finally responded stating their diagnosis did not d
NHTSA ODI #11592023
92,669 miles · Feb 1, 2024
Engine And Engine Cooling
The contact owns a 2012 BMW X3. The contact stated while driving 40 MPH, the vehicle was driving rough before stalling with the drivetrain malfunction warning light illuminated. The vehicle was taken to the dealer where the vehicle was diagnosed with a fault code variable camshaft timing control. The dealer made other repairs to…
Read full complaint
The contact owns a 2012 BMW X3. The contact stated while driving 40 MPH, the vehicle was driving rough before stalling with the drivetrain malfunction warning light illuminated. The vehicle was taken to the dealer where the vehicle was diagnosed with a fault code variable camshaft timing control. The dealer made other repairs to the vehicle, and the fault codes disappeared. However, the contact stated that the failure persisted. The contact took the vehicle back to the dealer and a local mechanic who confirmed a failure with the VANOS system. The contact referenced NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) as a possible solution however, the VIN was not included in the recall. The manufacturer was not notified of the failure. The failure mileage was approximately 92,669.
NHTSA ODI #11569246
115,000 miles · Aug 3, 2023
Power TrainCrash
The contact owns a 2012 BMW X3. The contact stated that after his wife parked the vehicle, she shifted the gear into the park (p) position however, after his wife exit the vehicle, the vehicle inadvertently rolled and crashed into a post without warning. No injuries were sustained. No medical attention was required. No police re…
Read full complaint
The contact owns a 2012 BMW X3. The contact stated that after his wife parked the vehicle, she shifted the gear into the park (p) position however, after his wife exit the vehicle, the vehicle inadvertently rolled and crashed into a post without warning. No injuries were sustained. No medical attention was required. No police report was filed. The contact notified AAA and upon inspection, the contact was informed that the was shifted to the park (p) position. The vehicle had not yet been diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 115,000.
NHTSA ODI #11536328
Mileage unknown · Jan 31, 2023
Air BagsSeats
A malfunction of the front seat occupancy mat will prevent the passenger air bag from deploying in the event of an accident and displays a malfunction warning. This malfunction has been the subject of several BMW NHTSA recalls but so far none have been issued for this vehicle.
NHTSA ODI #11504700
89,000 miles · Jun 6, 2022
Engine And Engine Cooling
The contact owns a 2012 BMW X3. The contact stated while driving at an undisclosed speed, the vehicle was shaking and hesitating during acceleration. An unknown warning light was illuminated. The vehicle was taken to an independent mechanic who related the failure to NHTSA Campaign Number: 14V176000 (Engine and Engine Cooling) h…
Read full complaint
The contact owns a 2012 BMW X3. The contact stated while driving at an undisclosed speed, the vehicle was shaking and hesitating during acceleration. An unknown warning light was illuminated. The vehicle was taken to an independent mechanic who related the failure to NHTSA Campaign Number: 14V176000 (Engine and Engine Cooling) however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA. The failure mileage was approximately 89,000.
NHTSA ODI #11467813
Mileage unknown · May 3, 2022
Air Bags
I am reporting a common issue I’ve seen a lot of BMWs have with the seat occupancy sensor. I just wanted to report this to see if it could be a potential recall, since it is a safety concern.
NHTSA ODI #11463165
Mileage unknown · Mar 28, 2022
Air Bags
OC3 mat in passenger seat malfunctions and disables passenger-side airbag. BMW is aware of this problem with OC3 sensors affecting different models. See, e.g., https://static.nhtsa.gov/odi/rcl/2017/RCRIT-17V428-3205.pdf pertaining to various E Series vehicles that have the same part. BMWNA claims the recall and extended war…
Read full complaint
OC3 mat in passenger seat malfunctions and disables passenger-side airbag. BMW is aware of this problem with OC3 sensors affecting different models. See, e.g., https://static.nhtsa.gov/odi/rcl/2017/RCRIT-17V428-3205.pdf pertaining to various E Series vehicles that have the same part. BMWNA claims the recall and extended warranties that covered the OC3 part in these other vehicles has not been extended to cover my vehicle (2012 BMW X3). There is a long documented history of problems with the OC3 sensor: https://static.nhtsa.gov/odi/tsbs/2018/MC-10142910-9999.pdf https://static.nhtsa.gov/odi/rcl/2017/RCRIT-17V428-3205.pdf https://static.nhtsa.gov/odi/rcl/2017/RCMN-17V605-2124.pdf (X3 OC3 mat from 2006-2010) https://static.nhtsa.gov/odi/tsbs/2014/SB-10056703-9690.pdf https://static.nhtsa.gov/odi/tsbs/2013/MC-10150131-9999.pdf https://static.nhtsa.gov/odi/tsbs/2020/MC-10179827-9999.pdf https://static.nhtsa.gov/odi/tsbs/2014/SB-10056096-7046.pdf
NHTSA ODI #11458679
Mileage unknown · Jul 29, 2021
Service Brakes
As I drive and stop, my brakes stick, when I try to accelerate it struggles to go. On the highway it began slowing me down. I was scared it was going to get me rear ended because my brake lights do not come on when this happens. I brought it to my garage and they diagnosed it to be the DSC pump. They put in a used pump and fixed…
Read full complaint
As I drive and stop, my brakes stick, when I try to accelerate it struggles to go. On the highway it began slowing me down. I was scared it was going to get me rear ended because my brake lights do not come on when this happens. I brought it to my garage and they diagnosed it to be the DSC pump. They put in a used pump and fixed the issue. Please take this seriously, it is a dangerous problem.
NHTSA ODI #11426987
Official recalls
2Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration