NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
147 reportsClear category filterMileage unknown · Nov 13, 2020
Engine
2013 X3 28I-DRIVETRAIN MALFUNCTION I HAD AN ISSUE YESTERDAY. 2013 X3 28I; 67K MILES. NO WARNING. ON EXPRESSWAY CAR FEELS LIKE ITS LOSING POWER SO I SLOW DOWN TO PULL TO SIDE. DRIVETRAIN MALFUNCTION WARNING COMES ON AS CAR IS DYING. HAD IT TOWED TO CLOSEST SHOP, NOT BWM. THEY SAY TIMING CHAIN TENSIONER FAILED AND LIKELY DID EXT…
Read full complaint
2013 X3 28I-DRIVETRAIN MALFUNCTION I HAD AN ISSUE YESTERDAY. 2013 X3 28I; 67K MILES. NO WARNING. ON EXPRESSWAY CAR FEELS LIKE ITS LOSING POWER SO I SLOW DOWN TO PULL TO SIDE. DRIVETRAIN MALFUNCTION WARNING COMES ON AS CAR IS DYING. HAD IT TOWED TO CLOSEST SHOP, NOT BWM. THEY SAY TIMING CHAIN TENSIONER FAILED AND LIKELY DID EXTENSIVE DAMAGE TO ENGINE. SHOP IS QUOTING $2500 TO REPLACE THE TENSIONER TO SEE IF ENGINE IS SHOT? ONCE THEY CONFIRM ENGINE IS DEAD $10K FOR REPLACEMENT ?? CAR IS OUT OF WARRANTY. ANY HELP MUCH APPRECIATED. THANKS
NHTSA ODI #11374494
80,000 miles · Oct 30, 2020
Engine
TIMING CHAIN FAILURE AS I WAS DRIVING ON THE FREEWAY. COMPLETE ENGINE SHUT DOWN. ENGINE HAS TO BE REPLACED.
NHTSA ODI #11372329
73,928 miles · Oct 29, 2020
Engine
ION OCT 27, 2020 WHILE DRIVING MY VEHICLE ACCOMPANIED BY MY WIFE, ON A LOCAL STREET IN THE VICINITY OF LAKE ZURICH, IL, A 'DRIVETRAIN MALFUNCTION' MESSAGE FLASHED ON THE DASHBOARD AND THE VEHICLE WENT INTO PARK MODE. I COULD NOT GET THE ENGINE TO RESTART AND HAD IT TOWED TO THE NEARBY BMW SERVICE CENTER. THE NEXT DAY, THE SERVI…
Read full complaint
ION OCT 27, 2020 WHILE DRIVING MY VEHICLE ACCOMPANIED BY MY WIFE, ON A LOCAL STREET IN THE VICINITY OF LAKE ZURICH, IL, A 'DRIVETRAIN MALFUNCTION' MESSAGE FLASHED ON THE DASHBOARD AND THE VEHICLE WENT INTO PARK MODE. I COULD NOT GET THE ENGINE TO RESTART AND HAD IT TOWED TO THE NEARBY BMW SERVICE CENTER. THE NEXT DAY, THE SERVICE ASSOCIATE SENT ME AN ESTIMATE, INFORMING THAT THERE WAS A CATASTROPHIC ENGINE FAILURE. BOTH THE ENGINE AND THE TURBOCHARGER NEED TO BE REPLACED WITH THE COST FOR SUCH AMOUNTING TO SOME $18000 + TAXES! THE VEHICLE ONLY HAS 73000 MILES AND I WAS TOLD BY THE SERVICE ASSOCIATE THAT I HAPPENED TO BE JUST UNLUCKY THAT THIS HAPPENED AND IT WAS NOT DUE TO ANYTHING I HAD DONE (OR OMITTED TO DO BY WAY OF ROUTINE MAINTENANCE). LOOKING AT ALL SUCH SIMILAR COMPLAINTS FOR THE 2013 MODEL YEAR FOR BMW X3, THERE IS OBVIOUSLY A DESIGN ISSUE WITH THE ENGINE AND ASSOCIATED COMPONENTS. I AM ALSO PARTICULARLY THANKFUL IT HAPPENED ON A SIDE STREET BEFORE I GOT ON TO THE HIGHWAY. THIS IS A HUGE SAFETY ISSUE AND BMW MUST BE HELD TO ACCOUNT FOR NOT ISSUING A RECALL OR CHANGING THEIR SERVICE PROCEDURES TO MITIGATE THE EFFECTS OF THE PROBLEM.
NHTSA ODI #11367037
111,000 miles · Oct 26, 2020
EngineFuel/propulsion SystemSteering
TWICE NOW WHILE DRIVING THE CAR IT JUST COMPLETELY STOPPED. NO WARNING AT ALL. JUST CAME TO A COMPLETE STOP AS I WAS DRIVING. THERE WERE NO WARNING LIGHTS, JUST HAPPENED. THE FIRST TIME WAS ON A BUSY ROAD, THE SECOND WAS ON A MUCH LESS BUSY STREET CLOSE TO MY HOME. I HAD IT FIXED TO THE TUNE OF OVER $3000 THE FIRST TIME A YEAR …
Read full complaint
TWICE NOW WHILE DRIVING THE CAR IT JUST COMPLETELY STOPPED. NO WARNING AT ALL. JUST CAME TO A COMPLETE STOP AS I WAS DRIVING. THERE WERE NO WARNING LIGHTS, JUST HAPPENED. THE FIRST TIME WAS ON A BUSY ROAD, THE SECOND WAS ON A MUCH LESS BUSY STREET CLOSE TO MY HOME. I HAD IT FIXED TO THE TUNE OF OVER $3000 THE FIRST TIME A YEAR AND A HALF AGO. NOW MY MECHANIC IS TELLING ME THAT IT IS THE TIMING CHAIN AND OIL PUMP DRIVE AND THAT WILL BE A VERY EXPENSIVE FIX. I AM BESIDE MYSELF. IF THIS HAD HAPPENED ON A BUSY HIGHWAY, LORD KNOWS WHAT WOULD HAVE HAPPENED BUT IT COULD'VE BEEN SOMETHING VERY CATASTROPHIC AND HORRIFIC. I AM A SINGLE MOTHER AND A WIDOW AND WITH THE PANDEMIC, I WAS OUT OF WORK FOR MANY MONTHS. I DO NOT KNOW WHAT I AM GOING TO DO BUT I CANNOT AFFORD TO FIX THIS CAR FOR SEVERAL THOUSANDS OF DOLLARS.
NHTSA ODI #11366564
88,848 miles · Oct 22, 2020
EnginePower Train
MY 2013 X3 JUST DEAD ON ME IN MIDDLE OF HIGHWAY, ON MY WAY TO WORK, WITHOUT AND AHEAD NOTICE, IT WAS JUST NOT EVEN 30 SECONDS SIGN OF "OIL PRESSURE LOW" THEN CHECK ENGINE LIGHT ON, CAR WAS SHAKING, IT TOTALLY LOST THE POWER, I CALLED ROAD SERVICE TO TOW IT TO DEALERSHIP. WHEN I CALLED THE BMW SERVICE CENTER, THE GIRL JUST TOLD M…
Read full complaint
MY 2013 X3 JUST DEAD ON ME IN MIDDLE OF HIGHWAY, ON MY WAY TO WORK, WITHOUT AND AHEAD NOTICE, IT WAS JUST NOT EVEN 30 SECONDS SIGN OF "OIL PRESSURE LOW" THEN CHECK ENGINE LIGHT ON, CAR WAS SHAKING, IT TOTALLY LOST THE POWER, I CALLED ROAD SERVICE TO TOW IT TO DEALERSHIP. WHEN I CALLED THE BMW SERVICE CENTER, THE GIRL JUST TOLD ME TO CLAM DOWN, DOESN'T NEED BE UPSET. I WAS SUPER UPSET, NEVER EXPECT TO DRIVE A CAR SUDDENLY DEAD IN MIDDLE OF HIGHWAY, IT COULD EASILY GET ME KILLED, OR CAUSE SERIOUSLY CAR ACCIDENT. IT WAS HAPPENED LAST MAY (2019), AT MILEAGE 88K, TWO OPTIONS: TRADE IT IN FOR $2K OR FIX IT $11,500 WITH REPLACE NEW ENGINE. I END PAID IT ALL FROM MY OWN POCKET. IT IS JUST ONE YEAR LATER, THE WARNING SIGN ON FOR " DRIVETRAIN MALFUNCTION, DRIVE MODERATELY, MAXIMUM DRIVETRAIN OUTPUT NOT AVAILABLE" SENT IT TO DEALERSHIP, I WAS TOLD THE TURBO NEED REPLACE, QUOTE FOR $5500... HOW COULD BMW SOLD THOSE POOR DESIGNED CRAP TO THEIR CUSTOMER, THE ISSUES JUST ONE AFTER ANOTHER, VERY DISAPPOINTED, SUCH SHAME ON BMW, I WOULD NOT BUY ANY BMW ANYMORE
NHTSA ODI #11365672
62,000 miles · Oct 20, 2020
Engine
I HAVE A 2013 BMW X3 WITH 100,110KM ON IT. ON OCTOBER 15, I WAS DRIVING NORMALLY, AND I GOT A MESSAGE ON MY DASH SAYING THERE WAS A 'DRIVETRAIN MALFUNCTION'. AFTER A FEW MINUTES, THE MESSAGE WENT AWAY AND LOW ENGINE OIL PRESSURE WARNING AND THE CHECK ENGINE LIGHT CAME ON. THE VEHICLE SLOW DOWN AND CAME TO A STOP AND AT THE END L…
Read full complaint
I HAVE A 2013 BMW X3 WITH 100,110KM ON IT. ON OCTOBER 15, I WAS DRIVING NORMALLY, AND I GOT A MESSAGE ON MY DASH SAYING THERE WAS A 'DRIVETRAIN MALFUNCTION'. AFTER A FEW MINUTES, THE MESSAGE WENT AWAY AND LOW ENGINE OIL PRESSURE WARNING AND THE CHECK ENGINE LIGHT CAME ON. THE VEHICLE SLOW DOWN AND CAME TO A STOP AND AT THE END LOCKED TO PARKING POSITION BY ITSELF. I HAD TO GET MY VEHICLE TOWED TO A MECHANIC WHO DIAGNOSE AND CONFIRM IT IS TIMING CHAIN FAILING AND SAID THAT THIS ISSUE IS A KNOWN PROBLEM WITH THIS MODEL OF BMW VEHICLE. I CALLED BMW CANADA THE FOLLOWING MORNING AND WAS TOLD TO GET IT CHECKED OUT BY PERFORMANCE BMW WHICH IS NEARBY DEALERSHIP. THE DEALERSHIP TOLD ME THE DIAGNOSE RESULT OF OIL PUMP CHAIN GUIDES BROKE AND TIMING CHAIN FAILURE AND ALSO TOLD ME THAT MY VEHICLE'S WARRANTY EXPIRED A FEW MONTHS AGO. BECAUSE OF THE PANDEMIC, I ALMOST NEVER DROVE THIS CAR SO IF I DROVE NORMALLY, THIS ISSUE WOULD HAVE COME UP MUCH SOONER, PROBABLY BEFORE THE WARRANTY EXPIRED. I WOULD LIKE TO REQUEST AN EXTENSION OF MY WARRANTY TO COVER THIS ISSUE AS I READ ONLINE THAT IT IS A VERY COMMON ISSUE WITH THIS VEHICLE MODEL (BECAUSE OF THE PLASTIC FRAME FOR THE TIMING CHAIN AND OIL PUMP CHAIN). WHEN IT'S A COMMON ISSUE, BMW SHOULD MAKE A RECALL! SOMEBODY MIGHT GET KILLED SOONER OR LATER IF THE ENGINE FAIL HAPPEN ON BUSY TRAFIC HIGHWAY!!!!
NHTSA ODI #11365352
87,280 miles · Oct 2, 2020
EnginePower Train
ROUTINE OIL CHANGE AND MECHANIC ADVISED IMMINENT TIMING CHAIN FAILURE BECAUSE OF ENGINE WHINING (87280 MILES). SERVICE MANAGER RECOMMENDED NOT DRIVING THE CAR BECAUSE OF LIKELY ENGINE FAILURE. AFTER TIMING CHAIN REPLACEMENT, DRIVETRAIN MALFUNCTION LIGHT CAME ON REPEATEDLY WHILE DRIVING AT VARIOUS ELEVATIONS AND SPEEDS. TOOK TO D…
Read full complaint
ROUTINE OIL CHANGE AND MECHANIC ADVISED IMMINENT TIMING CHAIN FAILURE BECAUSE OF ENGINE WHINING (87280 MILES). SERVICE MANAGER RECOMMENDED NOT DRIVING THE CAR BECAUSE OF LIKELY ENGINE FAILURE. AFTER TIMING CHAIN REPLACEMENT, DRIVETRAIN MALFUNCTION LIGHT CAME ON REPEATEDLY WHILE DRIVING AT VARIOUS ELEVATIONS AND SPEEDS. TOOK TO DEALER WHO ADVISED NOISY TURBO WASTEGATE LIKELY PROBLEM (88,919 MILES). TIMING CHAIN DEFECT WELL KNOWN TO BMW BUT ONLY WARRANTEED FOR 70,000 MILES IS DISINGENUOUS. ENGINE FAILURE ON A CAR AVERAGING 12.5K MILES A YEAR WITH LESS THAN 100K WITH KNOWN ENGINE DEFECTS IS FRUADULENT AT A MINIMUM.
NHTSA ODI #11362455
89,000 miles · Sep 27, 2020
EngineFuel/propulsion SystemPower Train
CAR HAS 89000 MILES. AT LOW SPEEDS, IT DRIVES FINE. ON HIGHWAY, "DRIVE TRAIN MALFUNCTION" LIGHT APPEARS DURING MODERATE-HEAVY ACCELERATION. TODAY, ON A CROWDED 4 LANE HIGHWAY AT ABOUT 70MPH, CAR LOST ALL POWER, GAS PEDAL WAS USELESS. I WAS BARELY ABLE TO LIMP TO BREAKDOWN LANE AND SPEED DROPPED TO ABOUT 15-20 MPH BY THE TIME I C…
Read full complaint
CAR HAS 89000 MILES. AT LOW SPEEDS, IT DRIVES FINE. ON HIGHWAY, "DRIVE TRAIN MALFUNCTION" LIGHT APPEARS DURING MODERATE-HEAVY ACCELERATION. TODAY, ON A CROWDED 4 LANE HIGHWAY AT ABOUT 70MPH, CAR LOST ALL POWER, GAS PEDAL WAS USELESS. I WAS BARELY ABLE TO LIMP TO BREAKDOWN LANE AND SPEED DROPPED TO ABOUT 15-20 MPH BY THE TIME I COULD GET THERE, THROUGH LOTS OF HONKING AND SEVERAL NEAR ACCIDENTS. EXTREMELY DANGEROUS. I SHUT THE CAR OFF FOR ABOUT 2 MINUTES, RESTARTED IT AND IT WORKED AGAIN. I TRAVELLED AT ABOUT 55MPH IN RIGHT LANE THE NEXT 15 MILES HOME WITHOUT ISSUE. I WAS WITH MY WIFE AND 7 YEAR OLD DAUGHTER. THIS IS A VERY SERIOUS AND DANGEROUS ISSUE TO HAVE WITH A CAR.
NHTSA ODI #11361325
90,000 miles · Sep 13, 2020
EnginePower Train
CAR DISPLAYED SIGN DRIVE-TRAIN MALFUNCTION/OIL PRESSURE LOW AND WITHIN 30 SECONDS STOPPED. IT WENT FROM 50 MPH TO ZERO IN 30 SECONDS. I BARELY SURVIVED A MAJOR ACCIDENT OVER A BUSY HIGHWAY (RT 78 EAST BOUND IN NJ). LATER ON BMW SERVICE CENTER REPORTED ENGINE FAILED FOR UNKNOWN REASON. I CAME TO KNOW THERE ARE MULTIPLE COMPLA…
Read full complaint
CAR DISPLAYED SIGN DRIVE-TRAIN MALFUNCTION/OIL PRESSURE LOW AND WITHIN 30 SECONDS STOPPED. IT WENT FROM 50 MPH TO ZERO IN 30 SECONDS. I BARELY SURVIVED A MAJOR ACCIDENT OVER A BUSY HIGHWAY (RT 78 EAST BOUND IN NJ). LATER ON BMW SERVICE CENTER REPORTED ENGINE FAILED FOR UNKNOWN REASON. I CAME TO KNOW THERE ARE MULTIPLE COMPLAINT AGAINST BMX X3 2013 SIMILAR MODEL AND MANY DRIVERS LIKE ME BARELY SURVIVED A MAJOR ACCIDENT. BMW IS PLAYING WITH OUR LIVES BY NOT RECALLING THIS MODEL. IT IS CLEARLY A MAJOR MANUFACTURING FAULT IN THIS ENGINE. THERE ARE MULTIPLE LAWSUITS ON BMW BUT I DO NOT HEAR ANY POSITIVE OUTCOME. I CAN NOT BELIEVE NO AUTHORITY IS TAKING ANY ACTION ON BMW FOR MAKING FAULTY CAR LIKE THIS AND NOT HOLDING THEM ACCOUNTABLE.
NHTSA ODI #11354669
87,482 miles · Aug 31, 2020
Engine
BOUGHT THIS VEHICLE IN OCTOBER, 2018 (72,685 MILES). IN OCTOBER, 2019, VEHICLE STOPPED WHILE DRIVING, WOULDN'T RESTART OR EVEN GO IN NEUTRAL, MILEAGE WAS ONLY AT 87,482. AUTOBAHN DEALERSHIP IN FT WORTH, TX DIAGNOSED TIMING CHAIN DEFECT WHICH CAUSED ENGINE FAILURE & WE WERE CHARGED $193.67 FOR THE DIAGNOSIS AND QUOTED $14,000 T…
Read full complaint
BOUGHT THIS VEHICLE IN OCTOBER, 2018 (72,685 MILES). IN OCTOBER, 2019, VEHICLE STOPPED WHILE DRIVING, WOULDN'T RESTART OR EVEN GO IN NEUTRAL, MILEAGE WAS ONLY AT 87,482. AUTOBAHN DEALERSHIP IN FT WORTH, TX DIAGNOSED TIMING CHAIN DEFECT WHICH CAUSED ENGINE FAILURE & WE WERE CHARGED $193.67 FOR THE DIAGNOSIS AND QUOTED $14,000 TO REPLACE THE ENGINE. BMW N.AMERICA WOULD NOT HELP US AT ALL ON THIS. I HAVE READ THAT THIS N20 ENGINE HAS FAILED (&TIMING CHAIN) IN HUNDREDS OF THESE CARS. SO THIS CAR IS SITTING IN MY DRIVEWAY, I'M STILL MAKING PAYMENTS & INSURANCE ON THIS BECAUSE WE DON'T HAVE THE FINANCES TO REPLACE THIS ENGINE. ALSO MY DAUGHTER WAS DRIVING THE CAR AT THE TIME & IT COULD HAVE CAUSED A SERIOUS ACCIDENT.
NHTSA ODI #11352326
Official recalls
7Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.
Illustration