NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
147 reportsClear category filter77,000 miles · Jun 4, 2021
Engine
The contact owns a 2013 BMW X3. The contact stated that while driving at approximately 40 MPH, the vehicle stalled with the "Transmission malfunction, drive accurately," warning message displayed on the instrument panel. The contact coasted the vehicle to the side of the road and had the vehicle towed to an independent mechanic.…
Read full complaint
The contact owns a 2013 BMW X3. The contact stated that while driving at approximately 40 MPH, the vehicle stalled with the "Transmission malfunction, drive accurately," warning message displayed on the instrument panel. The contact coasted the vehicle to the side of the road and had the vehicle towed to an independent mechanic. The contact was informed by the mechanic that the engine had seized and recommended that the vehicle be taken to an authorized dealer. The contact had the vehicle towed to an unnamed dealer where it was confirmed that the engine had seized and needed to be replaced. the dealer provided an estimate for the repair. The contact attempted to reach the manufacturer but was unable to reach a representative. The vehicle was not repaired. The approximate failure mileage was 77,000.
NHTSA ODI #11419662
Mileage unknown · May 27, 2021
EnginePower TrainVehicle Speed Control
The system that failed was the TIMING CHAIN AND CHAIN TENSIONER. The vehicle stalled while I was driving on the interstate. Immediately, I had no power and had to maneuver the vehicle to the emergency lane, placing me and other drivers in extreme danger. The problem was inspected, confirmed and repaired by the vehicle dealer.…
Read full complaint
The system that failed was the TIMING CHAIN AND CHAIN TENSIONER. The vehicle stalled while I was driving on the interstate. Immediately, I had no power and had to maneuver the vehicle to the emergency lane, placing me and other drivers in extreme danger. The problem was inspected, confirmed and repaired by the vehicle dealer. Prior to stalling, there were no warning lights to indicate a problem. The lights did come on simultaneously with the engine failure.
NHTSA ODI #11418703
Mileage unknown · May 27, 2021
EnginePower TrainVehicle Speed Control
Vehicle indicated a drivetrain malfunction. It was determined by the dealer that the system that failed was TIMING VALVETRONIC MOTOR. The vehicle stalled as I was making a left hand turn off of a busy highway, putting myself and oncoming traffic at serious risk of collision. Oncoming vehicles were able to slow until I was ab…
Read full complaint
Vehicle indicated a drivetrain malfunction. It was determined by the dealer that the system that failed was TIMING VALVETRONIC MOTOR. The vehicle stalled as I was making a left hand turn off of a busy highway, putting myself and oncoming traffic at serious risk of collision. Oncoming vehicles were able to slow until I was able to maneuver the vehicle out of the lane of oncoming traffic. The dealer confirmed that they "found the vehicle stalling and not running correctly. Performed vehicle test. Found faults for valvetronic motor. Set multiple additional faults for mixture and air mass. Valvetronic is failing and should be replaced." The vehicle component was inspected by the dealer who sold me the car. There were no warning lights nor other indicators of component failure prior to the vehicle stalling on the highway. This is the second time this vehicle has stalled in dangerous situations. The first time was a drivetrain malfunction/engine failure due to TIMING CHAIN AND TIMING TENSIONER malfunction. Most likely the VALVETRONIC SYSTEM failure is directly related to the TIMING CHAIN TENSIONER malfunction. Both systems failed within a very short period of time, and within fewer than 4,000 miles of each other.
NHTSA ODI #11418702
Mileage unknown · Apr 30, 2021
EnginePower Train
MY 2013,_BMW X3 CHECK ENGINE LIGHT WENT ON AND I NOTICED POWER LOSS WHEN IT DIDN'T DRIVE OVER 40MPH. I HAD THE VEHICLE DIAGNOSTICS DONE AT MY LOCAL BMW SHOP AND THEY TOLD ME I HAVE A BAD TIMING CHAIN AND SPROCKETS AND GAVE ME A BILL IN THE THOUSANDS. I CALLED BMW CORPORATE AND SPOKE TO LORI WHO IS AWARE OF THE ISSUE AND SAID, AN…
Read full complaint
MY 2013,_BMW X3 CHECK ENGINE LIGHT WENT ON AND I NOTICED POWER LOSS WHEN IT DIDN'T DRIVE OVER 40MPH. I HAD THE VEHICLE DIAGNOSTICS DONE AT MY LOCAL BMW SHOP AND THEY TOLD ME I HAVE A BAD TIMING CHAIN AND SPROCKETS AND GAVE ME A BILL IN THE THOUSANDS. I CALLED BMW CORPORATE AND SPOKE TO LORI WHO IS AWARE OF THE ISSUE AND SAID, AN EXTENDED WARRANTY WAS ISSUED BUT THAT IT EXPIRED IN 2018. THEY OFFERED ME NO OTHER FINANCIAL ASSISTANCE BECAUSE MY CAR HAS 100,499 MILES. SO THAT'S IT A CAR DIES AT 100,000 MILES AND THEY CAN'T HELP??? THAT'S AWFUL. THERE'S SO MANY COMPLAINTS ABOUT THIS ISSUE. MY OTHER 2007 BMW X3 HUGE PROBLEMS TOO OVERHEATING, MY MOTOR MOUNT BOLT BROKE THE ENGINE DROPPED AND BROKE THE WATER PUMP. GARBAGE, GARBAGE, GARBAGE I WILL NEVER BUY BMW. SHAME ON BMW FOR NOT HELPING!!!! MY TOYOTA WENT PAST 200,000 MILES AND IT'S STILL DRIVING.
NHTSA ODI #11414638
55,000 miles · Mar 14, 2021
Electrical SystemEngine
WHEN AT STOP LIGHT THE CAR STALLS OR WHEN I'M AT A STOP SIGN STALLS ENGINE VERY DANGEROUS AND DEVELOPED ANXIETY DRIVING IT, GUST WEEK OIL CAN OUT BACK AND ODD ENGIN SOUND MAKING NOISE, IT HAD TO GET TOWED BUT IRA TOYOTA SUCKERED ME. THEY CAN'T GET IN THE ENGINE TO INSPECT IT. I CAN'T DRIVE IT ON HIGHWAYS AT ALL SCARED IT WILL EN…
Read full complaint
WHEN AT STOP LIGHT THE CAR STALLS OR WHEN I'M AT A STOP SIGN STALLS ENGINE VERY DANGEROUS AND DEVELOPED ANXIETY DRIVING IT, GUST WEEK OIL CAN OUT BACK AND ODD ENGIN SOUND MAKING NOISE, IT HAD TO GET TOWED BUT IRA TOYOTA SUCKERED ME. THEY CAN'T GET IN THE ENGINE TO INSPECT IT. I CAN'T DRIVE IT ON HIGHWAYS AT ALL SCARED IT WILL ENGINE STOP
NHTSA ODI #11402834
120,000 miles · Feb 2, 2021
Engine
MY ENGINE WAS REPLACED IN 2019 AT A BMW CERTIFIED DEALERSHIP WHERE I PURCHASED. IN JULY 2020 THE CAR BROKE DOWN AND WAS TOWED IN TO BMW RADIATOR WAS REPLACED AND DID NOT FIX THE PROBLEM. I WAS THEN TOLD IT WAS ENGINE FAILURE, THAT WOULD NOT BE COVERED. I HAVE BEEN WITHOUT A VEHICLE FOR MONTHS.
NHTSA ODI #11394255
85,000 miles · Jan 9, 2021
EnginePower Train
DRIVE TRAIN MALFUNCTION HAPPENED MULTIPLE TIMES AND THE ENGINE JUST STOPPED WHILE DRIVING AT 55MPH - THE ENGINE STOPPED COMPLETELY IN MAY 2018 AND DIED. I TOOK IT INTO THE DEALERSHIP MANY TIMES BUT THEY COULD NOT FIND OUT WHAT WAS CAUSING THE PROBLEM. I NO LONGER OWN THE CAR BECAUSE OF THE ENGINE FAILURE.
NHTSA ODI #11387297
112,000 miles · Dec 10, 2020
Engine
BOUGHT 2013 BMW X3 WITH ABOUT 90,000 MILES ON IT. IN 2/2020 HAD ENGINE OIL PRESSURE LOW LIGHT COME ON AND TOOK TO BMW DEALERSHIP. THEY COULD NOT IDENTIFY A PROBLEM OTHER THAN A MINOR LEAK AND SUGGESTED REPLACING GASKET; IF OIL LIGHT CONTINUED TO COME ON TO BRING IT BACK AND NEXT OPTION WOULD DRAINING OIL/INSPECTING OIL PUMP WITH…
Read full complaint
BOUGHT 2013 BMW X3 WITH ABOUT 90,000 MILES ON IT. IN 2/2020 HAD ENGINE OIL PRESSURE LOW LIGHT COME ON AND TOOK TO BMW DEALERSHIP. THEY COULD NOT IDENTIFY A PROBLEM OTHER THAN A MINOR LEAK AND SUGGESTED REPLACING GASKET; IF OIL LIGHT CONTINUED TO COME ON TO BRING IT BACK AND NEXT OPTION WOULD DRAINING OIL/INSPECTING OIL PUMP WITH CAMERA; ALSO MADE COMMENT REGARDING NEEDING TO POSSIBLY REPLACE TIMING CHAIN BUT DUE TO COST WAS THE LAST OPTION. THE BMW STAFF DID NOT MAKE ME AWARE OF WHAT I LATER BECAME AWARE OF... BMW X3 HAVING ISSUES WITH THE CHAIN GUIDE, LATER LEADING TO TIMING ISSUES/ENGINE FAILURE. THE LIGHT CAME ON AGAIN SO I TOOK THE CAR TO AN INDEPENDENT SHOP THAT SPECIALIZES IN FOREIGN CARS. THEY COULD NOT SEE ANYTHING MAJOR AFTER NUMEROUS TEST DRIVES; ENGINE CLEANER WAS ADDED; OIL CHANGED. LIGHT WOULD COME ON OCCASIONALLY (ONCE EVERY MONTH); WOULD PULL OVER, WAIT FOR CAR TO COOL DOWN AND RESTART... NO LIGHT RETURNED. TOOK CAR FOR ANOTHER OIL CHANGE AND MECHANIC REPORTED NOT EVEN SEEING THE ERROR CODES WHEN DIAGNOSTIC COMPLETED? DROVE FOR ANOTHER SEVERAL MONTHS UNTIL LATE OCTOBER, EARLY NOVEMBER WHEN CODES STARTED BACK ON OCCASION. IN NOVEMBER, HAD LEFT THE CAR IDLING TO FOR QUICK STOP AND WHEN ATTEMPTING TO PULL OUT OF DRIVEWAY, THE CAR STALLED. IT SOUNDED LIKE IT WANTED TO START BUT WOULD NOT. WAS 1/2 IN DRIVEWAY AND 1/2 OUT INTO ROAD BLOCKING TRAFFIC. WAS ABLE TO GET PUSHED OUT OF ROAD; STILL WOULD NOT START. TOWED- MECHANIC REPORTED TIMING CHAIN HAD SLACK, CAUSING TIMING ISSUE AND ENGINE TO STOP. MECHANIC ALSO DID RESEARCH ON PROBLEM AND LOCATED CLASS ACTION SUIT. AFTER RESEARCHING REALIZED THERE WERE WARNING SIGNS AND IF BMW DEALER WOULD HAVE BEEN UP FRONT ABOUT WHAT WAS ALREADY KNOWN (TIMING CHAIN GUIDE ISSUES); THE PARTS COULD HAVE BEEN REPLACED 8.5 MONTHS AGO WITHOUT CAR SUDDENLY STOPPING. LUCKILY LOCAL AND NOT ON HIGHWAY WHILE DRIVING 65 MILES AN HOUR.
NHTSA ODI #11382845
87,530 miles · Dec 6, 2020
EnginePower TrainUnknown Or Other
THE VEHICLE HAS BEEN TO SHOP 2 TIMES.1ST DRIVETRAIN LIGHT CAME ON AND CAR WOULD SLOW DOWN IN THE MIDDLE OF THE HIGHWAY.THEN IT WOULD TOTALLY STOP. 2ND TIME IT DID THE SAME THING EXCEPT OIL PRESSURE LIGHT CAME ON SAYING PRESSURE TOO LOW AND IT STOPPED RIGHT THERE IN THE MIDDLE OF THE STREET. NOW THE OIL PRESSURE LIGHT COMES ON EV…
Read full complaint
THE VEHICLE HAS BEEN TO SHOP 2 TIMES.1ST DRIVETRAIN LIGHT CAME ON AND CAR WOULD SLOW DOWN IN THE MIDDLE OF THE HIGHWAY.THEN IT WOULD TOTALLY STOP. 2ND TIME IT DID THE SAME THING EXCEPT OIL PRESSURE LIGHT CAME ON SAYING PRESSURE TOO LOW AND IT STOPPED RIGHT THERE IN THE MIDDLE OF THE STREET. NOW THE OIL PRESSURE LIGHT COMES ON EVERY TIME I DRIVE IT. I'M AFRAID IT WILL STOP IN THE MIDDLE OF THE HIGHWAY AGAIN.
NHTSA ODI #11378136
110,839 miles · Dec 2, 2020
Engine
I BOUGHT THIS PRE-OWNED VEHICLE (A) BECAUSE IT WAS A BMW THAT WAS KNOWN TO BE OF SUPERIOR WORKMANSHIP AND MECHANICAL EXPERTISE, AS HERALDED BY BMW MEDIA, AND (B) BECAUSE IT WAS IN EXCELLENT CONDITION WITH SUPERIOR SERVICE RECORDS ' CARFAX NOTED 'NO ISSUES REPORTED' DURING ITS ENTIRE LIFE ON NEW MEXICO ROADWAYS: 105,508 MILES. MY…
Read full complaint
I BOUGHT THIS PRE-OWNED VEHICLE (A) BECAUSE IT WAS A BMW THAT WAS KNOWN TO BE OF SUPERIOR WORKMANSHIP AND MECHANICAL EXPERTISE, AS HERALDED BY BMW MEDIA, AND (B) BECAUSE IT WAS IN EXCELLENT CONDITION WITH SUPERIOR SERVICE RECORDS ' CARFAX NOTED 'NO ISSUES REPORTED' DURING ITS ENTIRE LIFE ON NEW MEXICO ROADWAYS: 105,508 MILES. MY VEHICLE DROVE PERFECTLY, WITH NO ISSUES, UNTIL APPROXIMATELY 4:00 PM ON OCTOBER 14, 2020, WHEN, AT 110,839 MILES, WITH NO WARNING OF AN ISSUE OF ANY KIND, THE ENGINE EXPERIENCED A CATASTROPHIC FAILURE, CAUSING ME TO QUICKLY SEARCH FOR A PLACE TO PULL OVER IN A CONGESTED AREA. I HAD BEEN TAKING MY GRANDSON TO A LESSON AND WAS LUCKY WE WEREN'T INJURED OR WORSE. IRONICALLY, ALTHOUGH IT WAS OBVIOUS THE VEHICLE WAS EXPERIENCING MASSIVE FAILURE, THE MESSAGE ON THE COMMUNICATIONS MODULE SAID, 'CONTINUE TO DRIVE CAREFULLY.' I HAD THE CAR DELIVERED AN TO A LONG-TIME, AWARD-WINNING, HIGHLY RESPECTED BMW MECHANIC. HIS ANALYSIS INDICATED THAT THERE WAS NO REPAIR AVAILABLE FOR MY CAR, AS THE PLASTIC GUIDE ASSEMBLY FOR THE PRIMARY TIMING CHAIN WAS MADE OF A DEFECTIVE POLYCARBONATE MATERIAL THAT BECAME BRITTLE AND BROKE APART, CREATING DEBRIS THAT LODGED IN THE CRANKSHAFT DRIVE SPROCKETS. THIS DEBRIS CAUSED THE PRIMARY CHAIN TO SKIP, LETTING THE CAMSHAFTS AND CRANKSHAFT FALL OUT OF SYNC, WHICH DESTROYED THE ENGINE. BOTTOM LINE: I WOULD HAVE TO COMPLETELY REPLACE THE N20 ENGINE TO THE TUNE OF $11,163.81 (AT BMW $15K OR MORE). THERE IS A LESS EXPENSIVE OPTION: AN ENGINE WITH AT LEAST 70K MILES. PROBLEM IS, IT HAS A 70K MILE TIMING CHAIN. SO, IT WOULD HAVE TO BE REPLACED AND ONLY HAS A ONE YEAR OPTION, AS OPPOSED TO TWO YEARS. BMW AMERICA WILL DO NOTHING TO HELP, EVEN THOUGH THEY'VE KNOWN ABOUT THE ISSUE SINCE 2012, WHICH IS FRAUDULENT, BASED ON WHAT I'VE SEEN FROM CLAIMANTS WITH THE SAME ISSUE ONLINE!
NHTSA ODI #11377538
Official recalls
7Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.
Illustration