ON YEAR AFTER PUCHASING CAR, AND AFTER WARRANTY PERIOD, STARTING GETTING DRIVETRAIN MALFUNCTION ERROR. SMOKED ON TURNING ON IGNITION A COUPLE OF TIMES. TOOK TO BMW AND WAS TOLD IT NEEDED A TURBO. WAS TOLD BY BMW MECHANIC THAT EVERY ONE OF THIS MODEL NEEDED A NEW TURBO. $6000. INTERNET BLOG SITES ALSO INDICATE THAT THE TURBO GOES…
Read full complaint
ON YEAR AFTER PUCHASING CAR, AND AFTER WARRANTY PERIOD, STARTING GETTING DRIVETRAIN MALFUNCTION ERROR. SMOKED ON TURNING ON IGNITION A COUPLE OF TIMES. TOOK TO BMW AND WAS TOLD IT NEEDED A TURBO. WAS TOLD BY BMW MECHANIC THAT EVERY ONE OF THIS MODEL NEEDED A NEW TURBO. $6000. INTERNET BLOG SITES ALSO INDICATE THAT THE TURBO GOES OUT ALL THE TIME. IF IT IS A MANUFACTURERS DEFECT NEW THEN THIS SHOULD BE A RECALL. PEOPLE CAN'T PAY $6000 ON NEW CARS FOR TURBOS WHEN THEY KNOW IT IS DEFECTIVE.
NHTSA ODI #10863918
75,000 miles · Mar 7, 2016
EnginePower TrainUnknown Or OtherFire
HAD BEEN DRIVING FOR APPROX. 5 MINUTES IN RESIDENTIAL AREA. CHECK ENGINE LIGHT, LOW OIL PRESSURE WARNING & BLACK SMOKE THRU DASHBOARD. COULD SEE FLAMES UNDER THE HOOD. WITHIN 5-6 MINUTES CAR WAS FULLY ENGULFED IN FLAMES. NOTHING LEFT EXCEPT FOR THE FRAME. TOTAL LOSS, ALMOST NO WARNING.
NHTSA ODI #10840341
60,000 miles · Nov 25, 2015
Engine
TL* THE CONTACT OWNS A 2013 BMW X3. THE CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE STALLED WITHOUT WARNING. THE CONTACT STATED THAT THE FAILURE RECURRED INTERMITTENTLY. THE CONTACT STATED THAT THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE ENGINE NEEDED TO BE REPAIRED. THE VEHICLE WAS N…
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. THE CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE STALLED WITHOUT WARNING. THE CONTACT STATED THAT THE FAILURE RECURRED INTERMITTENTLY. THE CONTACT STATED THAT THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE ENGINE NEEDED TO BE REPAIRED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 60,000.
NHTSA ODI #10806770
Mileage unknown · Dec 16, 2014
Engine
FIRSTLY APPROXIMATE INCIDENT DATE IS APPROXIMATE AND MAY BE OFF. ITS JUST BEEN OVER 2 YEARS I HAVE OWNED THIS BMW AND I HAVE KEPT MY BMW FOR CHECK ENGINE ERROR REPAIR FOR 4 TIMES AT STEVENS CREEK BMW. 3 TIMES OUT OF THIS 4 HAS BEEN BETWEEN JUNE 2014 TO TILL DATE. ONCE AGAIN THE CHECK ENGINE ERROR IS ON WHICH MAKES IT THE 5T…
Read full complaint
FIRSTLY APPROXIMATE INCIDENT DATE IS APPROXIMATE AND MAY BE OFF. ITS JUST BEEN OVER 2 YEARS I HAVE OWNED THIS BMW AND I HAVE KEPT MY BMW FOR CHECK ENGINE ERROR REPAIR FOR 4 TIMES AT STEVENS CREEK BMW. 3 TIMES OUT OF THIS 4 HAS BEEN BETWEEN JUNE 2014 TO TILL DATE. ONCE AGAIN THE CHECK ENGINE ERROR IS ON WHICH MAKES IT THE 5TH TIME. AT THIS POINT I DON'T THINK THIS BMW IS RELIABLE AND I DON'T HAVE THE ENERGY AND PATIENCE TO KEEP TAKING APPOINTMENTS AND GETTING SUCH ERRORS FIXED ON MONTHLY BASIS. I DON'T INTEND TO KEEP USING THIS VEHICLE AND GETTING IT FIXED ON MONTHLY BASIS. ITS GOOD THAT MY BMW IS STILL UNDER THE 4 YEAR COVERAGE BUT IF THIS WASN'T AVAILABLE THEN I WOULD HAVE INCURRED HUGE EXPENSES ON MONTHLY BASIS TO GET THESE ERRORS FIXED. GETTING THE SAME ERROR ON REPEATED BASIS PROVES THAT THIS BMW HAS A MANUFACTURING DEFECT. BMW CUSTOMER RELATIONS ISN'T HELPING ME ON THIS. THEY ARE JUST WASTING TIME SAYING WE ARE GETTING REPORTS FROM DEALER AND AWAITING THE BMW WESTERN REGIONAL TEAM TO LOOK INTO THIS. THE LAST CHECK ENGINE LIGHT CAME ON DURING THANKSGIVING BREAK AND I TOOK AN APPOINTMENT WITH STEVENS CREEK BMW FOR 12/03/2014. ON 12/02/2014 THE CHECK ENGINE LIGHT DIDN'T COME ON. I CHECKED WITH STEVENS CREEK BMW AND THEY SAID SINCE THE CHECK ENGINE LIGHT ISN'T ON WE CAN'T DIAGNOSE THE REASON WHY IT HAD SWITCHED ON SO PLEASE DON'T BRING IN THE BMW AS WE WONT BE OF ANY HELP. SO I DIDN'T BRING MY BMW TO DEALER WORKSHOP. BASED ON THIS BMW REGIONAL MANAGEMENT HAS DENIED LOOKING INTO MY CASE AND SAID WE CAN'T PROVIDE ANY ASSISTANCE. *TR
NHTSA ODI #10664633
13,500 miles · Aug 28, 2014
Engine
MY WIFE WAS DRIVING ON A LOCAL SIDE STREET (SPEED LIMIT 25 MPH) AT A SPEED OF APPROXIMATELY 20 MPH AND I WAS SITTING IN THE PASSENGER SEAT. WE WERE COMING UPON NUMEROUS STOP SIGNS, SO IN ORDER TO AVOID THE BMW AUTOSTART/STOP FEATURE (THIS FEATURE SHUTS THE CAR ENGINE OFF WHEN THE CAR STOPS TO SAVE FUEL) FROM ACTIVATING, I REACHE…
Read full complaint
MY WIFE WAS DRIVING ON A LOCAL SIDE STREET (SPEED LIMIT 25 MPH) AT A SPEED OF APPROXIMATELY 20 MPH AND I WAS SITTING IN THE PASSENGER SEAT. WE WERE COMING UPON NUMEROUS STOP SIGNS, SO IN ORDER TO AVOID THE BMW AUTOSTART/STOP FEATURE (THIS FEATURE SHUTS THE CAR ENGINE OFF WHEN THE CAR STOPS TO SAVE FUEL) FROM ACTIVATING, I REACHED OVER TO TURN OFF THE AUTOSTART BUTTON. THIS BUTTON IS LOCATED DIRECTLY NEXT TO THE START/STOP BUTTON. INSTEAD, I ACCIDENTALLY HIT THE START/STOP BUTTON (THIS IS A KEYLESS CAR) AND WHILE TRAVELING AT 20 MPH THE CAR ENGINE SHUT OFF AND WE HAD TO COAST TO A STOP WITHOUT POWER STEERING OR ANY POWER, BEFORE BEING ABLE TO START THE CAR. IN ORDER TO RESTART THE CAR, THE BRAKE PEDAL MUST BE PRESSED. IF THIS HAPPENED WHILE AT HIGHWAY SPEEDS, AN ACCIDENT WOULD HAVE BEEN VERY LIKELY TO HAVE OCCURRED. THIS IS A DESIGN SAFETY ISSUE THAT NEEDS REPLACEMENT/RECALL. *TR
IN STOP AND GO TRAFFIC ON THE INTERSTATE I WAS BRAKING AFTER MOVING FORWARD A FEW FEET AND THE ENGINE STARTED RACING CAUSING THE CAR TO LURCH FORWARD (GIVEN I WAS ON THE BRAKE) UNTIL THE BRAKE WOULD NOT HOLD ANY LONGER AT WHICH POINT THE CAR ACCELERATED IN TRAFFIC DESPITE ME PUSHING EVEN HARDER ON THE BRAKE. THE BRAKE WAS COMPLE…
Read full complaint
IN STOP AND GO TRAFFIC ON THE INTERSTATE I WAS BRAKING AFTER MOVING FORWARD A FEW FEET AND THE ENGINE STARTED RACING CAUSING THE CAR TO LURCH FORWARD (GIVEN I WAS ON THE BRAKE) UNTIL THE BRAKE WOULD NOT HOLD ANY LONGER AT WHICH POINT THE CAR ACCELERATED IN TRAFFIC DESPITE ME PUSHING EVEN HARDER ON THE BRAKE. THE BRAKE WAS COMPLETELY UNRESPONSIVE AT THIS POINT. I AVOIDED REAR ENDING THE CAR IN FRONT OF ME BY SWERVING AROUND HIM BUT COULD NOT AVOID THE VEHICLE FARTHER AHEAD IN TRAFFIC AND HIT THE RIGHT REAR OF A UHAUL STORAGE UNIT TOWED BY A VEHICLE AND THE BMW FLIPPED ONTO ITS RIGHT SIDE. MIRACULOUSLY, WE WALKED AWAY WITH ONLY MINOR CUTS, SCRAPES, AND BRUISES. SEAT RESTRAINTS AND AIRBAGS WORKED PERFECTLY WHICH IS THE ONLY KIND THING WE CAN NOW SAY DESPITE HAVING NO PRIOR ISSUES. WHETHER IT IS AN ONBOARD COMPUTER MALFUNCTION OR NOT WE WILL NEVER OWN ANOTHER BMW... AND IF THE OTHER ONLINE POSTS HAVE BEEN THERE WHEN I PURCHASED THE VEHICLE IN SEPT 2012 (AND HAD I READ THEM) THEN I NEVER WOULD HAVE PURCHASED THE VEHICLE. COUPLED WITH OTHER CARCOMPLAINT.COM, BMW COMMUNITY BLOGS, AND NHTSA POSTS SURROUNDING 2012 AND 2013 X3 EVENTS OF THE IDENTICAL NATURE THERE SHOULD BE AN IMMEDIATE INVESTIGATION AS TO THE SIMULTANEOUS AND CONCURRENT EVENT OF THE THROTTLE ACCELERATION WHILE BRAKING, AND THE BRAKES FAILING (AS IF THE COMPUTER THINKS THE BRAKE PEDAL IS THE GAS PEDAL?) .. AND A RECALL BEFORE DEATHS OCCUR ... THOUGH IT IS LIKELY THEY'VE ALREADY OCCURRED SINCE THE DEAD CAN'T TESTIFY AS TO A PROBLEM THAT OTHER BMW DEALER SERVICE DEPARTMENTS FAIL TO REPLICATE AND THEREFORE DISCOUNT. THE BACK HATCH OF OUR VEHICLE ALSO FLIPPED OPEN ALLOWING ITEMS TO FALL ONTO THE HIGHWAY (DESPITE NO IMPACT TO THE REAR OF THE VEHICLE) THOUGH ALL PASSENGER CAR DOORS REMAINED CLOSED. THE VEHICLE HAS BEEN TOTALED. WE WOULD CERTAINLY NOT GET INTO THAT CAR EVER AGAIN EVEN IF IT WERE REPAIRABLE. *TR
NHTSA ODI #10584220
150 miles · Mar 15, 2013
Engine
TL* THE CONTACT OWNS A 2013 BMW X3. THE CONTACT STATED THAT WHILE TRYING TO ACCELERATE FROM A STOP THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO THE DEALER. AFTER INSPECTION, THEY ADVISED HER THAT THE VEHICLE WAS ACTING AS NORMAL. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS CONTACTED AND THEY OFFERED NO AS…
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. THE CONTACT STATED THAT WHILE TRYING TO ACCELERATE FROM A STOP THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO THE DEALER. AFTER INSPECTION, THEY ADVISED HER THAT THE VEHICLE WAS ACTING AS NORMAL. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS CONTACTED AND THEY OFFERED NO ASSISTANCE. THE FAILURE MILEAGE WAS APPROXIMATELY 150. THE CURRENT MILEAGE WAS APPROXIMATELY 200. THE VIN WAS UNAVAILABLE. *TR
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.
2013 BMW X3 Problems, Complaints & Recalls | Skip That Year
Illustration