NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
147 reportsClear category filter84,899 miles · Jan 1, 2020
Electrical SystemEngineFuel/propulsion System
1. WARNING DRIVE TRAIN MALFUNCTION 2. DROVE MODERATELY ON WAY DRIVING IN TO DEALERSHIP FOR REPAIR 3. OIL PRESSURE LOW STOP OR RISK DAMAGE TO ENGINE 4. PULLED OVER, HAD IT TOWED TO BMW 5. THEY CALLED THE NEXT MORNING STATING IT WAS 17,000 MOL DUE TO ENGINE BEING DAMAGED AFTER FRAGMENTS WENT IN FROM TIMING CHAIN 6. INSURANCE …
Read full complaint
1. WARNING DRIVE TRAIN MALFUNCTION 2. DROVE MODERATELY ON WAY DRIVING IN TO DEALERSHIP FOR REPAIR 3. OIL PRESSURE LOW STOP OR RISK DAMAGE TO ENGINE 4. PULLED OVER, HAD IT TOWED TO BMW 5. THEY CALLED THE NEXT MORNING STATING IT WAS 17,000 MOL DUE TO ENGINE BEING DAMAGED AFTER FRAGMENTS WENT IN FROM TIMING CHAIN 6. INSURANCE ADJUSTER WENT OUT AND CONQUERED BMW ISSUE TIMING CHAIN BROKE EFFECTING ENGINE OIL PUMP AND BATTERY 7. ENGINE INOPERABLE FUCNTIONALLY TOTALED CAR WAITING FOR BMW N AMERICA CASEMNGR TO RETURN MY CALL AND HOPEFULLY OFFER TO EXTEND WARRANTY OR OFFER GOOD WILL AND FIX -REPAIR ENGINE AND ALL RELATED TO MALFUNCTION 8. FOUND OUT USA CONSUMER CLASS ACTION SUIT IS CURRENTLY UNDER WAY FILED 12/12/19 AGAINST BMW FOR TIMING CHAIN ENGINE ISSUE... STILL WITHOUT RELIEF OR VEHICLE AND NO PERSONAL FUNDS TO GET CAR BACK AGAIN HOPING FOR RELIEF FROM BMW!
NHTSA ODI #11292447
84,666 miles · Nov 26, 2019
Engine
CAR WAS IN MOTION ON A SUBURB ROAD WHEN DASHBOARD LIGHT UP WITH 'DRIVETRAIN MALFUNCTION'.TIMING CHAIN BROKE AND DAMAGED THE ENGINE. THE CAR STOPPED IN THE MIDDLE OF ROAD ON AN INCLINE, BLOCKING THE TRAFFIC THAT COULD CAUSE ACCIDENT. VEHICLE ODO WAS 84666. THERE IS A TSB SI B11 03 17 ON THIS ISSUE, BUT THE WARRANTY EXPIRED AT 7 …
Read full complaint
CAR WAS IN MOTION ON A SUBURB ROAD WHEN DASHBOARD LIGHT UP WITH 'DRIVETRAIN MALFUNCTION'.TIMING CHAIN BROKE AND DAMAGED THE ENGINE. THE CAR STOPPED IN THE MIDDLE OF ROAD ON AN INCLINE, BLOCKING THE TRAFFIC THAT COULD CAUSE ACCIDENT. VEHICLE ODO WAS 84666. THERE IS A TSB SI B11 03 17 ON THIS ISSUE, BUT THE WARRANTY EXPIRED AT 7 YEARS / 70,000 MILES.
NHTSA ODI #11282527
107,000 miles · Nov 13, 2019
Engine
WE EXPERIENCED A COMPLETE ENGINE FAILURE WHILE DRIVING THE VEHICLE AT APPROXIMATELY 40 MILES PER HOUR ON A CITY STREET. WE RECEIVED A "DRIVETRAIN MALFUNCTION" WARNING, SOMETHING THAT WE HAVE RECEIVED INTERMITTENTLY OVER THE PAST YEAR, WHICH WAS PREVIOUSLY DIAGNOSED AS A MINOR ISSUE. WE NOTICED A CHANGE IN ENGINE NOISE AND PERFOR…
Read full complaint
WE EXPERIENCED A COMPLETE ENGINE FAILURE WHILE DRIVING THE VEHICLE AT APPROXIMATELY 40 MILES PER HOUR ON A CITY STREET. WE RECEIVED A "DRIVETRAIN MALFUNCTION" WARNING, SOMETHING THAT WE HAVE RECEIVED INTERMITTENTLY OVER THE PAST YEAR, WHICH WAS PREVIOUSLY DIAGNOSED AS A MINOR ISSUE. WE NOTICED A CHANGE IN ENGINE NOISE AND PERFORMANCE, WHICH WAS UNUSUAL. WHILE ATTEMPTING TO BRING THE CAR TO A BMW DEALERSHIP FOR SERVICE, A "LOW OIL PRESSURE" WARNING CAME ON AND THE ENGINE QUIT APPROXIMATELY 10 SECONDS LATER. I WAS ABLE TO COAST THE VEHICLE INTO A PARKING LOT, WHERE WE HAD IT TOWED TO THE DEALERSHIP. THE DEALERSHIP DIAGNOSED IT AS A FAILURE OF THE TIMING CHAIN GUIDES AND ADVISED US THAT THE ENGINE NEEDED TO BE REPLACED. THANKFULLY, WE WERE OPERATING UNDER THE FAVORABLE CONDITIONS TO SAFELY STOP THE VEHICLE; HOWEVER, THE FAILURE IS SUDDEN AND POTENTIALLY DANGEROUS. THROUGH RESEARCH, WE NOW KNOW THAT THIS IS A COMMON PROBLEM WITH THE ENGINE FOR THIS PARTICULAR YEAR AND MODEL. WE ATTEMPTED TO RESOLVE THE ISSUE WITH BMW NORTH AMERICA. THEY ARE AWARE THAT THIS IS A COMMON PROBLEM AND WERE UNWILLING TO PROVIDE ANY ASSISTANCE.
NHTSA ODI #11279761
122,000 miles · Nov 12, 2019
Engine
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE THE CONTACT'S FIANC WAS DRIVING APPROXIMATELY 35 MPH, THE VEHICLE SHUT OFF. ALSO, 'DRIVE TRAIN MALFUNCTION, DRIVE MODERATE SPEED' WAS ILLUMINATED ON THE INSTRUMENT PANEL. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHO WAS UNABLE TO DIAGNOSE THE FAILURE. THE VEHICLE WAS TOWED TO BIL…
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE THE CONTACT'S FIANC WAS DRIVING APPROXIMATELY 35 MPH, THE VEHICLE SHUT OFF. ALSO, 'DRIVE TRAIN MALFUNCTION, DRIVE MODERATE SPEED' WAS ILLUMINATED ON THE INSTRUMENT PANEL. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHO WAS UNABLE TO DIAGNOSE THE FAILURE. THE VEHICLE WAS TOWED TO BILL DODGE AUTO PARK (888-464-1978, LOCATED AT 2 SAUNDERS WAY, WESTBROOK, ME 04092) WHERE IT WAS DIAGNOSED THAT THE VALVE COVER WAS CRACKED AND NEEDED TO BE REMOVED TO INSPECT THE TIMING CHAINS. THE TECHNICIAN STATED THAT THE ENGINE MAY NEED TO BE REPLACED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND DID NOT ASSIST. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 122,000.
NHTSA ODI #11279597
84,304 miles · Sep 19, 2019
Engine
THE ENGINE EXPERIENCED A SUDDEN ENGINE FAILURE WHILE DRIVING ON A HIGHWAY. THE FAILURE APPEARS TO BE FROM THE FAILURE OF THE PLASTIC GUIDE AND TENSIONING MECHANISM THAT IS USED IN TIMING CHAIN ASSEMBLY. THE PLASTIC BREAKS AND WEDGED BETWEEN THE TIMING CHAIN AND CRANKSHAFT TIMING SPROCKET CAUSING THE TIMING TO JUMP AND DAMAGE T…
Read full complaint
THE ENGINE EXPERIENCED A SUDDEN ENGINE FAILURE WHILE DRIVING ON A HIGHWAY. THE FAILURE APPEARS TO BE FROM THE FAILURE OF THE PLASTIC GUIDE AND TENSIONING MECHANISM THAT IS USED IN TIMING CHAIN ASSEMBLY. THE PLASTIC BREAKS AND WEDGED BETWEEN THE TIMING CHAIN AND CRANKSHAFT TIMING SPROCKET CAUSING THE TIMING TO JUMP AND DAMAGE THE VALVETRAIN.
NHTSA ODI #11256765
51,000 miles · Aug 14, 2019
Engine
WE PURCHASED A 2013 BMW X3 IN DECEMBER 2012. THE VEHICLE HAS BEEN DEALER SERVICED FROM DAY ONE. IN 2018, FAIRFAX BMW REPLACED THE TIMING CHAIN AT NO COST WHEN THE VEHICLE HAD ONLY 45K MILES WHICH IS HIGHLY UNUSUAL. IN EARLY AUGUST I WAS DRIVING ON INTERSTATE 81 SOUTH TRAVELLING FROM VIRGINIA TO ARIZONA. THE CAR BEGAN MAKING …
Read full complaint
WE PURCHASED A 2013 BMW X3 IN DECEMBER 2012. THE VEHICLE HAS BEEN DEALER SERVICED FROM DAY ONE. IN 2018, FAIRFAX BMW REPLACED THE TIMING CHAIN AT NO COST WHEN THE VEHICLE HAD ONLY 45K MILES WHICH IS HIGHLY UNUSUAL. IN EARLY AUGUST I WAS DRIVING ON INTERSTATE 81 SOUTH TRAVELLING FROM VIRGINIA TO ARIZONA. THE CAR BEGAN MAKING A TICKING SOUND WHICH BECAME PROGRESSIVELY LOUDER. I EXITED THE BUSY HIGHWAY AND BARELY MADE IT TO BMW OF ROANOKE, VA. I WAS TRAVELLING THE SPEED LIMIT WHEN THE PROBLEM BEGAN, AND WAS BARELY ABLE TO GO 45 MILES PER HOUR WHEN I EXITED. I SOON LEARNED THAT MY PARTICULAR ENGINE (F-25/N20) HAS A MAJOR DEFECT AND WILL LITERALLY BLOW UP WHILE DRIVING. BMW IS AWARE OF THE PROBLEM, AND HAS ENDANGERED MY HEALTH AND SAFETY BY REFUSING TO CORRECT THE PROBLEM. A CLASS ACTION LAWSUIT HAS BEEN FILED IN NEW JERSEY (CHRIS WILLIAMS, ET.AL. V. BMW NORTH AMERICA). THE DEALER IN ROANOKE SAID THE ENGINE IS UNREPAIRABLE WITH ONLY 51K MILES ON THE ODOMETER. ONE LAST OBSERVATION IN NOTICED IS THAT PRIOR TO STARTING MY TRIP I CHECKED THE ENGINE OIL LEVEL AND IT WAS ALMOST A QUART LOW WHICH HAD NEVER HAPPENED BEFORE. I FILLED THE ENGINE TO IT'S RECOMMENDED CAPACITY AND BEGAN MY TRAVEL. THERE IS A LIST OF AFFECTED VEHICLES WITH ENGINE DEFECTS, AND MY VEHICLE IS ON THE LIST.
NHTSA ODI #11243921
79,000 miles · Aug 8, 2019
Engine
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE DRIVING 15 MPH AND APPROACHING A STOP SIGN, THE CHECK ENGINE WARNING INDICATOR ILLUMINATED AND "DRIVETRAIN MALFUNCTION" AND "LOW OIL PRESSURE" APPEARED ON THE INSTRUMENT PANEL. IN ADDITION, THE CONTACT STATED THAT A RATTLING NOISE WAS COMING FROM THE ENGINE COMPARTMENT AND THE VEHICLE ST…
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE DRIVING 15 MPH AND APPROACHING A STOP SIGN, THE CHECK ENGINE WARNING INDICATOR ILLUMINATED AND "DRIVETRAIN MALFUNCTION" AND "LOW OIL PRESSURE" APPEARED ON THE INSTRUMENT PANEL. IN ADDITION, THE CONTACT STATED THAT A RATTLING NOISE WAS COMING FROM THE ENGINE COMPARTMENT AND THE VEHICLE STARTED TO SHAKE. THE CONTACT COASTED THE VEHICLE TO THE SIDE OF THE ROAD AND POWERED OFF THE ENGINE. THE VEHICLE FAILED TO RESTART AND WAS TOWED TO THE CONTACT'S RESIDENCE. THE FOLLOWING DAY, THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE TIMING CHAIN WAS FRACTURED AND THE ENGINE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT TAKEN TO A DEALER AND WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 79,000.
NHTSA ODI #11242524
115,000 miles · Jul 19, 2019
Engine
DRIVING ON HIGHWAY AROUND 70 MPH, DRIVETRAIN MALFUNCTION MESSAGE CAME ON MONITOR WITHIN A FEW SECONDS ANOTHER MESSAGE SAYING LOW OIL PRESSURE PULL TO SIDE AND CALL FOR SERVICE. MANGED TO PULL TO THE SIDE, BUT POTENTIAL WAS THERE AFTER LOSING POWER TO GET INTO AN ACCIDENT. I WAS 300 MILES FROM HOME ON JULY 4, 2019 NO SHOP WAS OP…
Read full complaint
DRIVING ON HIGHWAY AROUND 70 MPH, DRIVETRAIN MALFUNCTION MESSAGE CAME ON MONITOR WITHIN A FEW SECONDS ANOTHER MESSAGE SAYING LOW OIL PRESSURE PULL TO SIDE AND CALL FOR SERVICE. MANGED TO PULL TO THE SIDE, BUT POTENTIAL WAS THERE AFTER LOSING POWER TO GET INTO AN ACCIDENT. I WAS 300 MILES FROM HOME ON JULY 4, 2019 NO SHOP WAS OPEN, SO HAD AAA TOW THE VEHICLE TO BMW DEALER, MET WITH THEM THE NEXT DAY AND FOUND OUT IT WAS A TIMING CHAIN ISSUE AND NEEDED A NEW ENGINE, HE ALSO INFORMED THIS WAS A KNOWN ISSUE AND THE BMW HAD EXTENDED THE WARRANTY TO 70K MILES, BUT SINCE I HAD 115K IT WAS OUT OF WARRANTY. CALLED CORPORATE BMW AND INFORMED THEM THAT THIS IS THE KNOWN ISSUE OF TIMING CHAIN AND THEY SHOULD PROVIDE ASSISTANCE, I HAVE BEEN DRIVING BMW FOR OVER 10 YEARS AND CURRENTLY OWN 2. THEY CAME BACK AND SAID THEY WILL NOT BE GIVING ANY GOODWILL OR ANYTHING TO HELP WITH THE REPAIR. THEY WOULD NOT STAND BY THEIR VEHICLE ON A KNOWN ISSUE WITH A LOYAL CUSTOMER. NEEDLESS TO SAY, I WON'T BUY A VEHICLE FROM A COMPANY THAT DOES NOT STAND BY THEIR VEHICLE. I HAVE LOOKED AT THE DATABASE AND FOUND MANY VEHICLES WITH THE SAME EXACT ISSUE, ENOUGH FOR BMW TO EXTEND THE WARRANTY FOR THIS ISSUE BUT CURRENTLY NOT ENOUGH FOR AN INVESTIGATION OR RECALL.
NHTSA ODI #11233270
Mileage unknown · Jun 2, 2019
Engine
FAULTY PLASTIC TIMING CHAIN GUIDE THAT FAILS PREMATURELY. AT 113,000, MY MECHANIC IS TELLING ME TO EITHER REPLACE THE TIMING CHAIN AND COMPONENTS, OR GET RID OF THE VEHICLE, AS THE ENGINE WILL EVENTUALLY FAIL IF THIS IN NOT ADDRESSED. AT NEARLY 5K OR MORE IN REPAIRS, THAT IS BASICALLY 50% OF THE VEHICLE'S RESALE VALUE. BMW IS…
Read full complaint
FAULTY PLASTIC TIMING CHAIN GUIDE THAT FAILS PREMATURELY. AT 113,000, MY MECHANIC IS TELLING ME TO EITHER REPLACE THE TIMING CHAIN AND COMPONENTS, OR GET RID OF THE VEHICLE, AS THE ENGINE WILL EVENTUALLY FAIL IF THIS IN NOT ADDRESSED. AT NEARLY 5K OR MORE IN REPAIRS, THAT IS BASICALLY 50% OF THE VEHICLE'S RESALE VALUE. BMW IS AWARE OF THE ISSUE AND SHOULD ISSUE A RECALL FOR A BAD DESIGN AND FAULTY COMPONENTS. MANY OTHERS WITH THE BMW N20 ENGINE HAVE HAD THEIR ENGINE FAIL COMPLETELY, OR HAD TO PAY ASTRONOMICAL REPAIR COSTS TO CORRECT BMW'S DESIGN ERROR. A MULTI-BILLION DOLLAR COMPANY SHOULD BE HELD RESPONSIBLE FOR SELLING A PROBLEMATIC ENGINE, NOT THE OWNER.
NHTSA ODI #11217374
104,344 miles · May 29, 2019
Engine
DRIVING WEST ON I84 IN CT. JUST EAST OF EXIT 33 BEFORE RT 72 MERGE LOW OIL PRESSURE MESSAGE COMES ON. WITHIN 30 SECONDS DRIVETRAIN MALFUNCTION MESSAGE APPEARS AND THE ENGINE STARTS TO POWER DOWN. BARELY MADE IT ACROSS THE 2 LANES MERGING ON THE RIGHT AND ONTO THE SHOULDER BEFORE THE ENGINE LOST POWER ENTIRELY AND SHUT DOWN. …
Read full complaint
DRIVING WEST ON I84 IN CT. JUST EAST OF EXIT 33 BEFORE RT 72 MERGE LOW OIL PRESSURE MESSAGE COMES ON. WITHIN 30 SECONDS DRIVETRAIN MALFUNCTION MESSAGE APPEARS AND THE ENGINE STARTS TO POWER DOWN. BARELY MADE IT ACROSS THE 2 LANES MERGING ON THE RIGHT AND ONTO THE SHOULDER BEFORE THE ENGINE LOST POWER ENTIRELY AND SHUT DOWN. COULD HAVE BEEN A TOTAL DISASTER GIVEN THE HIGH SPEED MERGE AND VOLUME OF TRAFFIC.
NHTSA ODI #11210616
Official recalls
7Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.
Illustration