NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
29 reportsClear category filterMileage unknown · Oct 23, 2024
Electrical SystemEngine And Engine Cooling
The contact owns a 2013 BMW X3. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer…
Read full complaint
The contact owns a 2013 BMW X3. The contact received notification of NHTSA Campaign Number: 24V608000 (ENGINE AND ENGINE COOLING, ELECTRICAL SYSTEM); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
NHTSA ODI #11621619
130,000 miles · Sep 19, 2024
Electrical SystemEngine And Engine Cooling
The contact owns a 2013 BMW X3. The contact stated that while driving at an undisclosed speed, an unknown message displayed, and the vehicle lost motive power. The check engine warning light was illuminated. Additionally, the low brake fluid message displayed intermittently even when the brake fluid level was not low. The vehicl…
Read full complaint
The contact owns a 2013 BMW X3. The contact stated that while driving at an undisclosed speed, an unknown message displayed, and the vehicle lost motive power. The check engine warning light was illuminated. Additionally, the low brake fluid message displayed intermittently even when the brake fluid level was not low. The vehicle was towed to the dealer, where it was determined that the engine needed to be replaced. The vehicle was not repaired. Upon investigation, the contact discovered that the VIN was included in NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System); however, the part to do the recall repair was not yet available. The manufacturer was made aware of the failure and a case was opened. The failure mileage was approximately 130,000.
NHTSA ODI #11615487
Mileage unknown · Apr 3, 2023
Electrical SystemEngineFire
While being parked with the engine off and in a covered condominium garage for 12 days, my 2013 BMW X3 caught fire and burned until the fire fighters extinguished the fire. The engine burnt to the point of virtually disintegrating. Other areas of the car suffered extensive damage because of the heat but the insurance investigati…
Read full complaint
While being parked with the engine off and in a covered condominium garage for 12 days, my 2013 BMW X3 caught fire and burned until the fire fighters extinguished the fire. The engine burnt to the point of virtually disintegrating. Other areas of the car suffered extensive damage because of the heat but the insurance investigation established that the fire originated in the engine compartment. The car in the next parking spot also was a total loss and the building had damages. Fortunately, there were no injuries. The engine had been replaced by BMW, at an authorized dealer, in November of 2021 as part of a class action suit settlement. Therefore, although the car had approximately 76000 miles, the engine had only about 7000 miles. The last service it had was a regular oil change on October 6, 2022. The fire department investigation and a third party investigation contracted by my insurance company were not able to determine the cause of the fire, only that it started in the engine, but the third party report stated that further investigation could be conducted by a mechanical engineer to try to determine the root cause of the fire. BMW was contacted and initially offered to inspect the car but 4 weeks later they officially communicated to me that they were declining the inspection and offered me $1000 if I signed a general liability release. The car will be available for inspection for a limited time after the title is transferred to the insurance company. No indications of a problem had been noticed during the last days/weeks/months it was driven. No warnings of any kind or other symptoms. Additional photos of the car and the damages are available for review at any time. The insurance company investigation report is also available upon request.
NHTSA ODI #11515291
120,000 miles · Mar 3, 2022
Electrical SystemPower TrainVehicle Speed Control
My wife was driving the car (her main, work car) with our 13 year old. She called me upset and told me that the car would barely move. This was disturbing. She was in heavy traffic. Also the car has been mostly reliable and we only have above 120k on the vehicle after almost 10 years. My wife slowly made it down busy Stocton Blv…
Read full complaint
My wife was driving the car (her main, work car) with our 13 year old. She called me upset and told me that the car would barely move. This was disturbing. She was in heavy traffic. Also the car has been mostly reliable and we only have above 120k on the vehicle after almost 10 years. My wife slowly made it down busy Stocton Blvd. A few hundred feet and safely made it to a business parking lot. I came ASAP. (20min later). There was a message from the car - "Drive Train malfunction " it looked very serious. (Note: My wife is about the best, skillful and careful driver I know. Especially for a person originally from foreign country (China). I gave my wife and child my car and took over the situation. The car would only putt along at 5 mph. So with my emergency flashers on I drove it all the way home using the shoulder. Its about 5 miles home, (more or less). It was pretty crazy situation with how fast people drive on 65th Street expressway. This was my fastest route and only option. Before this a Firestone happened to be just across the street where my wife had parked it so I ask if they could help. "Not today" was their answer. I called BMW of Elk Grove, Ca. where we have always have taken it. Monica at BMW told me it sounded like a recall that had been happening. This was relieving since we haven't been financially well off. It was already 4-5pm so that's why I made the decision to try to make it home. At home I could get my affairs (phone) numbers in order and call for a tow in a much safer place. The unsafest part was getting the dangerous 5-10 miles home. It was Sunday but Monica at BMW said "no problem " just drop it off and they would look at it Monday morning. BMW is telling me over $1800 just to inspect. Not to mention how much for a new timing chain. Monica didn't tell me how much that us. I since looked it up. That's when I saw several similar stories of 2013 X3's which seems much more than coincidence so I'm writing you. Thank you for the opportunity
NHTSA ODI #11454952
55,000 miles · Mar 14, 2021
Electrical SystemEngine
WHEN AT STOP LIGHT THE CAR STALLS OR WHEN I'M AT A STOP SIGN STALLS ENGINE VERY DANGEROUS AND DEVELOPED ANXIETY DRIVING IT, GUST WEEK OIL CAN OUT BACK AND ODD ENGIN SOUND MAKING NOISE, IT HAD TO GET TOWED BUT IRA TOYOTA SUCKERED ME. THEY CAN'T GET IN THE ENGINE TO INSPECT IT. I CAN'T DRIVE IT ON HIGHWAYS AT ALL SCARED IT WILL EN…
Read full complaint
WHEN AT STOP LIGHT THE CAR STALLS OR WHEN I'M AT A STOP SIGN STALLS ENGINE VERY DANGEROUS AND DEVELOPED ANXIETY DRIVING IT, GUST WEEK OIL CAN OUT BACK AND ODD ENGIN SOUND MAKING NOISE, IT HAD TO GET TOWED BUT IRA TOYOTA SUCKERED ME. THEY CAN'T GET IN THE ENGINE TO INSPECT IT. I CAN'T DRIVE IT ON HIGHWAYS AT ALL SCARED IT WILL ENGINE STOP
NHTSA ODI #11402834
97,000 miles · Aug 29, 2020
Electrical SystemPower TrainService Brakes
AUGUST 10, 2020. I WAS DRIVING TO THE STORE ABUT 10 MILES FROM HOME ON A MAJOR HIGHWAY AND MY 2013 BMW X328I, SUDDENLY STARTED TO GO CRAZY IN A MANNER THAT I NEVER EXPERIENCED BEFORE A LOT OF LIGHTS SUCH AS, (ENGINE, ABS, DSC, DTC, BRAKES,POWERTRAIN, AND STIMULATION. THE VEHICLE BECAME NON-DRIVABLE AND A SAFETY HAZARDOUS IN NATU…
Read full complaint
AUGUST 10, 2020. I WAS DRIVING TO THE STORE ABUT 10 MILES FROM HOME ON A MAJOR HIGHWAY AND MY 2013 BMW X328I, SUDDENLY STARTED TO GO CRAZY IN A MANNER THAT I NEVER EXPERIENCED BEFORE A LOT OF LIGHTS SUCH AS, (ENGINE, ABS, DSC, DTC, BRAKES,POWERTRAIN, AND STIMULATION. THE VEHICLE BECAME NON-DRIVABLE AND A SAFETY HAZARDOUS IN NATURE THAT IT ALMOST CAUSE AN ACCIDENT. I ACT IN A EMERGENCY STATE OF MIND AND WAS ABLE TO PULL INTO A NEARBY PARKING LOT AT 15315 MERRY CAT LN, BELLE HAVEN, VA 23306. I PROCEEDED IN CALLING THE AAA TOWING COMPANY TO TAKE THE VEHICLE TO MY PLACE OF RESIDENT. *DT *TR
NHTSA ODI #11352000
134 miles · Jul 17, 2020
Electrical SystemEngineFuel/propulsion System
MY [XXX] NOW I'M GOING THROUGH SOMETHING VERY DIFFERENT IM BUY A CAR IN THE YEAR 2017 MARCH 20 I SPOKE THE SALE MANAGER REPRESENTATIVE ABOUT THE CAR COMBINATION OF MY CAR HIS NAME IS [XXX] EVERYTHING WAS FINE WELL MY CAR HAS BEEN DAMAGE SINCE 2017 BY THE MECHANIC OF THE G0GGIN BMW TREASURE COAST 4429 S US HWY 1 FT PIERCE FL 34…
Read full complaint
MY [XXX] NOW I'M GOING THROUGH SOMETHING VERY DIFFERENT IM BUY A CAR IN THE YEAR 2017 MARCH 20 I SPOKE THE SALE MANAGER REPRESENTATIVE ABOUT THE CAR COMBINATION OF MY CAR HIS NAME IS [XXX] EVERYTHING WAS FINE WELL MY CAR HAS BEEN DAMAGE SINCE 2017 BY THE MECHANIC OF THE G0GGIN BMW TREASURE COAST 4429 S US HWY 1 FT PIERCE FL 34982, TEI 429-8300 ...MY CAR NOW SERIOUS DAMAGE DON'T KNOWI IWAS GOING TO START A MOTOR SO OTHER MECHANIC TELL ME I HAVE TO REPLACE ENGINE I SIGN A 72 MONTH CONTRACT INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *CC *TR
NHTSA ODI #11340018
104,000 miles · Jul 3, 2020
Electrical SystemEngine
I WAS DRIVING MY 2013 BMW X3 ON I-280 FREEWAY SOUTHBOUND AROUND 11AM 6/10/2020, ALL OF SUDDEN MY CAR SHOWS BATTERY DISCHARGE RESULTED IN LOST OF POWER,WHEN THE SUV WAS AT 104,000 MILES. WITHIN 30 SECONDS, THE DRIVETRAIN MALFUNCTION WARNING ENGAGED. THE CAR BEGAN SHUTTING DOWN WHILE THEY WERE DRIVING ON THE FREEWAY. I WAS ABLE TO…
Read full complaint
I WAS DRIVING MY 2013 BMW X3 ON I-280 FREEWAY SOUTHBOUND AROUND 11AM 6/10/2020, ALL OF SUDDEN MY CAR SHOWS BATTERY DISCHARGE RESULTED IN LOST OF POWER,WHEN THE SUV WAS AT 104,000 MILES. WITHIN 30 SECONDS, THE DRIVETRAIN MALFUNCTION WARNING ENGAGED. THE CAR BEGAN SHUTTING DOWN WHILE THEY WERE DRIVING ON THE FREEWAY. I WAS ABLE TO SAFELY NAVIGATE ACROSS TWO LANES OF MERGING TRAFFIC TO GET OFF THE ROAD BEFORE THE ENGINE DIED. THE SITUATION COULD HAVE GONE VERY DIFFERENTLY WITH DISASTROUS RESULTS, SO I QUICKLY MANEUVERED THE VEHICLE AND PULLED OVER ON THE EMERGENCY PARKING LINE ON THE FREEWAY
NHTSA ODI #11337283
68,000 miles · Jun 30, 2020
Electrical SystemEnginePower Train
ON 6/23/20, AT APPROX., 6:15 AM, MY 2013 BMW X3 VEHICLE (APPROX. 68,000 MILES) LOST ENGINE POWER AS I WAS ATTEMPTING TO PULL OUT FROM A BUSY AND CONGESTED N/B 215 FREEWAY (NEAR THE W/B 10 FREEWAY EXCHANGE) IN COLTON, CALIFORNIA. PRIOR TO LOSING ENGINE POWER, AND AT ABOUT LESS THAN ONE MINUTES BEFORE, MY VEHICLE'S LOW OIL LIGHT …
Read full complaint
ON 6/23/20, AT APPROX., 6:15 AM, MY 2013 BMW X3 VEHICLE (APPROX. 68,000 MILES) LOST ENGINE POWER AS I WAS ATTEMPTING TO PULL OUT FROM A BUSY AND CONGESTED N/B 215 FREEWAY (NEAR THE W/B 10 FREEWAY EXCHANGE) IN COLTON, CALIFORNIA. PRIOR TO LOSING ENGINE POWER, AND AT ABOUT LESS THAN ONE MINUTES BEFORE, MY VEHICLE'S LOW OIL LIGHT SENSOR HAD COME ON, THEN QUICKLY CHANGED TO A DRIVETRAIN MALFUNCTION SENSOR -- WARNING ME TO DRIVE MODERATELY, BUT THAT WAS MEANINGLESS BECAUSE MY VEHICLE HAD ALREADY BEGAN TO LOSE ENGINE POWER. I SLID TO A SLOW STOP INTO THE EMERGENCY LANE OF THE FREEWAY AFTER CUTTING OFF NUMEROUS VEHICLES BEHIND ME IN AN EFFORT TO MAKE IT OFF THE FREEWAY.
NHTSA ODI #11331733
84,899 miles · Jan 1, 2020
Electrical SystemEngineFuel/propulsion System
1. WARNING DRIVE TRAIN MALFUNCTION 2. DROVE MODERATELY ON WAY DRIVING IN TO DEALERSHIP FOR REPAIR 3. OIL PRESSURE LOW STOP OR RISK DAMAGE TO ENGINE 4. PULLED OVER, HAD IT TOWED TO BMW 5. THEY CALLED THE NEXT MORNING STATING IT WAS 17,000 MOL DUE TO ENGINE BEING DAMAGED AFTER FRAGMENTS WENT IN FROM TIMING CHAIN 6. INSURANCE …
Read full complaint
1. WARNING DRIVE TRAIN MALFUNCTION 2. DROVE MODERATELY ON WAY DRIVING IN TO DEALERSHIP FOR REPAIR 3. OIL PRESSURE LOW STOP OR RISK DAMAGE TO ENGINE 4. PULLED OVER, HAD IT TOWED TO BMW 5. THEY CALLED THE NEXT MORNING STATING IT WAS 17,000 MOL DUE TO ENGINE BEING DAMAGED AFTER FRAGMENTS WENT IN FROM TIMING CHAIN 6. INSURANCE ADJUSTER WENT OUT AND CONQUERED BMW ISSUE TIMING CHAIN BROKE EFFECTING ENGINE OIL PUMP AND BATTERY 7. ENGINE INOPERABLE FUCNTIONALLY TOTALED CAR WAITING FOR BMW N AMERICA CASEMNGR TO RETURN MY CALL AND HOPEFULLY OFFER TO EXTEND WARRANTY OR OFFER GOOD WILL AND FIX -REPAIR ENGINE AND ALL RELATED TO MALFUNCTION 8. FOUND OUT USA CONSUMER CLASS ACTION SUIT IS CURRENTLY UNDER WAY FILED 12/12/19 AGAINST BMW FOR TIMING CHAIN ENGINE ISSUE... STILL WITHOUT RELIEF OR VEHICLE AND NO PERSONAL FUNDS TO GET CAR BACK AGAIN HOPING FOR RELIEF FROM BMW!
NHTSA ODI #11292447
Official recalls
7Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.
Illustration