NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
21 reportsClear category filterMileage unknown · Jun 14, 2026
Structure
Bed is rusting out from the bottom in a fashion that looks very similar to a previous Tundra bed rusting issue that had a TSB and remedy from Toyota. On the driver's side bed bolt closest to the cab, the sheet metal tack welded to the bed has separated and is rusting out. Approximately 7 inches to the drivers side from that bol…
Read full complaint
Bed is rusting out from the bottom in a fashion that looks very similar to a previous Tundra bed rusting issue that had a TSB and remedy from Toyota. On the driver's side bed bolt closest to the cab, the sheet metal tack welded to the bed has separated and is rusting out. Approximately 7 inches to the drivers side from that bolt. The seam sealer is also cracking. Additionally, the drivers side bed bolt closes to the tailgate has rust bubbling up from underneath approximately 1 inch to the passenger side from the bolt and also along where that sheet metal is tack welded onto the bed.
NHTSA ODI #11744041
Mileage unknown · Mar 20, 2025
Structure
I have had multiple incidents where the front hood bulge has blown off going down the interstate and nearly hit other cars. It’s not been worth buying a new one with the risk of them flying off. It’s definitely a saftey concern and a hazard.
NHTSA ODI #11649615
Mileage unknown · Feb 17, 2025
StructureUnknown Or Other
The frame of the truck is extremely rusted. I am unsure if it can be fixed. It is available for inspection. This 2016 Tundra has 71,000 miles and is used as a third car. It has been serviced at the same dealership (Northshore Toyota, Covington, LA) and we were never informed of the damage by the dealership. My safety is at …
Read full complaint
The frame of the truck is extremely rusted. I am unsure if it can be fixed. It is available for inspection. This 2016 Tundra has 71,000 miles and is used as a third car. It has been serviced at the same dealership (Northshore Toyota, Covington, LA) and we were never informed of the damage by the dealership. My safety is at risk because the extensive rust could cause the frame to fail. Previous Tundra models have been recalled because of the same issues. No warnings were issued even after the dealership serviced the truck on a lift numerous times (approximately 9 years). The only previous warning by the dealership was on 1/29/2025 when the dealership informed us of a rusty trailer hitch. The truck was brought to 4 body shops in the local area after the owner went to work on the trailer hitch and saw the damage. All 4 shops confirmed that the rust was extensive. 3 shops would not fix the damage because it would be an expensive/extensive fix. We are waiting on what shop #4 says.
NHTSA ODI #11643127
Mileage unknown · Nov 5, 2024
Structure
Peeling paint. White paint is separating from primer on hood, and adjacent to windshield on a pillars and the leading edge if the roof.
NHTSA ODI #11623575
99,000 miles · Sep 7, 2023
Structure
The contact owns a 2016 Toyota Tundra. The contact stated that while driving at an undisclosed speed, the vehicle ran off the road during a thunderstorm, causing the driver's and passenger's side curtain air bags to deploy. The vehicle was towed to the dealer, who informed the contact that the headliner needed to be replaced; h…
Read full complaint
The contact owns a 2016 Toyota Tundra. The contact stated that while driving at an undisclosed speed, the vehicle ran off the road during a thunderstorm, causing the driver's and passenger's side curtain air bags to deploy. The vehicle was towed to the dealer, who informed the contact that the headliner needed to be replaced; however, the part to complete the repair was not available. The manufacturer was made aware of the failure and confirmed that parts were not yet available. The failure mileage was approximately 99,000.
NHTSA ODI #11543094
76,000 miles · Sep 10, 2019
Structure
TL* THE CONTACT OWNS A 2016 TOYOTA TUNDRA. WHILE THE CONTACT WAS SERVICING THE VEHICLE, THE BUMPER DETACHED WHEN A FRIEND STEPPED ON THE BUMPER. PRIOR TO THE FAILURE, THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 17V051000 (STRUCTURE). THE CONTACT DROVE TO AUTONATION TOYOTA SOUTH AUSTIN (4800 S IH 35 FRONTAGE R…
Read full complaint
TL* THE CONTACT OWNS A 2016 TOYOTA TUNDRA. WHILE THE CONTACT WAS SERVICING THE VEHICLE, THE BUMPER DETACHED WHEN A FRIEND STEPPED ON THE BUMPER. PRIOR TO THE FAILURE, THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 17V051000 (STRUCTURE). THE CONTACT DROVE TO AUTONATION TOYOTA SOUTH AUSTIN (4800 S IH 35 FRONTAGE RD, AUSTIN, TX 78745, 512 518-6900) AND WAS INFORMED THAT SINCE THE VEHICLE WAS PREVIOUSLY INVOLVED IN A CRASH, THEY WOULD NOT REPLACE THE BUMPER. THE MANUFACTURER WAS CONTACTED AND SIDED WITH THE DEALER; HOWEVER, THEY FELT THE RECALL SHOULD STILL BE REMEDIED. THE MANUFACTURER REFERRED THE CONTACT TO SAN MARCOS TOYOTA (5101 I-35, SAN MARCOS, TX 78666, 512-392-1999) WHERE THEY POINTED OUT DAMAGE TO THE SIDE AND REAR OF THE VEHICLE AND ALSO REFUSED TO SERVICE THE RECALL. THE CONTACT CALLED THE MANUFACTURER BACK AND FILED A COMPLAINT REGARDING THE REFUSAL OF SERVICE. THE CONTACT DROVE TO UNIVERSAL TOYOTA (12102 I-35, SAN ANTONIO, TX 78233, 726-444-6959) WHERE THE VEHICLE WAS REPAIRED. THE FAILURE MILEAGE WAS 76,000. THE VIN WAS UNKNOWN.
NHTSA ODI #11254522
31,000 miles · Apr 23, 2019
SeatsStructure
TL* THE CONTACT OWNS A 2016 TOYOTA TUNDRA. UPON INSPECTING THE VEHICLE, THE CONTACT NOTICED RUST ON THE FRAME OF THE REAR SEAT. THE VEHICLE WAS TAKEN TO HERTRICH TOYOTA OF MILFORD (1367 BAY RD, MILFORD, DE 19963, (877) 458-0609) WHERE THE CONTACT WAS INFORMED THAT THE CAUSE OF THE FAILURE WAS DUE TO MOISTURE ENTERING THE VEHICLE…
Read full complaint
TL* THE CONTACT OWNS A 2016 TOYOTA TUNDRA. UPON INSPECTING THE VEHICLE, THE CONTACT NOTICED RUST ON THE FRAME OF THE REAR SEAT. THE VEHICLE WAS TAKEN TO HERTRICH TOYOTA OF MILFORD (1367 BAY RD, MILFORD, DE 19963, (877) 458-0609) WHERE THE CONTACT WAS INFORMED THAT THE CAUSE OF THE FAILURE WAS DUE TO MOISTURE ENTERING THE VEHICLE. THE CONTACT CLEANED THE RUST, BUT THE FAILURE RECURRED WITH EVEN MORE RUST. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 31,000.
NHTSA ODI #11203198
36,000 miles · Jun 29, 2018
Structure
REAR BUMPER RECALL. AS OUTLINED IN TOYOTA TUNDRA REAR BUMPER RECALL. THE REINFORCEMENT CRACKED AND SOMEONE STEPPED ON THE BUMPER COVER AND NOW THE DEALER AND TOYOTA WILL NOT PREFORMED THE NEEDED REPAIRS STATING THE THE VEHICLE WAS IN A ACCIDENT AND SHOULD BE REPAIRED UNDER INSURANCE.
NHTSA ODI #11104657
Mileage unknown · Jan 7, 2018
Structure
THERE IS A KNOWN RECALL ON THE REAR BUMPER BRACKETS. FOR NEARLY 6 MONTHS, THE DEALERS IN SOUTH FLORIDA (ESP TOYOTA OF NORTH MIAMI) HAVE BEEN UNABLE TO ASSIST IN REMEDY OF THIS ISSUE AS THEY DO NOT HAVE THE PARTS IN STOCK.
NHTSA ODI #11061020
6,491 miles · Sep 26, 2017
Structure
WHILE BACKING UP, I TAPPED A POLE STICKING OUT OF THE GROUND AND DENT MY PLASTIC BUMPER. I TOOK THE VEHICLE INTO A BODY SHOP WHERE THEY HAD TO ORDER THE BUMPER AND ASSEMBLY. SEVERAL DAYS LATER WHILE DRIVING DOWN THE STREET, THE RIGHT REAR PORTION OF THE BUMPER FELL OFF. WHAT HELD IT IN PLACE WAS THE ELECTRICAL FOR THE BACKUP S…
Read full complaint
WHILE BACKING UP, I TAPPED A POLE STICKING OUT OF THE GROUND AND DENT MY PLASTIC BUMPER. I TOOK THE VEHICLE INTO A BODY SHOP WHERE THEY HAD TO ORDER THE BUMPER AND ASSEMBLY. SEVERAL DAYS LATER WHILE DRIVING DOWN THE STREET, THE RIGHT REAR PORTION OF THE BUMPER FELL OFF. WHAT HELD IT IN PLACE WAS THE ELECTRICAL FOR THE BACKUP SENSOR. I ENDED UP USING TAPE TO HOLD THE BUMPER TO THE PICKUP AND WENT BACK TO THE BODY SHOP THE NEXT DAY.AS THE PARTS HAD COME IN. TOYOTA SAID THAT SINCE I BACKED INTO THE POLE THERE WAS NO COVERAGE FOR THE BRACKET OR BUMPER EVEN THOUGH THERE WAS A RECALL ON THE BUMPER BRACKETS I LATTER LEARNED.. THE BUMPER BRACKETS THAT HELD THE BUMPER IN PLACE WAS PURCHASED FROM A TOYOTA DEALERSHIP. IF I WAS TAPPED IN A REAR END ACCIDENT AND THE BUMPER FELL OFF IT NOW BECOMES A SAFETY ISSUE WITH THIS VEHICLE. PHOTOS OF THE DAMAGE PRIOR AND THE BUMPER DID NOT FALL OFF. THE BUMPER FELL OFF BECAUSE OF SAFETY DEFECT OF THIS VEHICLE WHILE DRIVING DOWN THE STREET IN THE CITY.
NHTSA ODI #11030013
Official recalls
5Nov 23, 2021
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Consequence & remedy
Consequence: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Additional source detail variants (2)
Steering:hydraulic Power Assist System
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Consequence: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Steering:rack And Pinion
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Consequence: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Jun 29, 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016 Tundra vehicles. The affected vehicles have a passenger knee air bag module that was attached to the instrument panel mounting brackets with incorrect bolts.
Consequence & remedy
Consequence: The incorrect bolts may cause the air bag module to loosen over time, affecting the performance of the knee airbag, increasing the risk of injury during a crash.
Remedy: All of the affected vehicles have been inspected and any incorrect knee air bag mounting bolts have been replaced, free of charge. The recall began on June 22, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is H0K.
May 11, 2017
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2013-2017 Toyota Tundra and Sequoia vehicles accessorized with Southeast Toyota accessory 20-inch Rockstar wheels installed by Southeast Toyota or a Southeast Toyota dealer. The Rockstar wheels were installed with lugnuts that may crack and detach.
Consequence & remedy
Consequence: Lugnuts that crack and detach may cause the wheels to separate from the vehicle, increasing the risk of a crash.
Remedy: SET will notify owners, and dealers will install new replacement lugnuts, free of charge. The recall began June 23, 2017. Owners may contact SET customer service at 1-866-405-4226. SET's number for this recall is SET17A.
Jan 24, 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016-2017 Tundra vehicles equipped with a resin rear step bumper and resin reinforcement brackets (vehicles with chrome step bumpers are not affected). In the event of an impact to the corner of the bumper, the resin bracket may be damaged but not be noticed.
Consequence & remedy
Consequence: If a person steps on the corner of the bumper that is damaged, a portion of the bumper may break away, increasing the risk of injury.
Remedy: Toyota will notify owners, and dealers will replace the resin rear bumper reinforcement brackets with steel ones, and replace the rear bumper tread, free of charge. The recall began on May 21, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is H0C.
Jun 9, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2016 Toyota Camry and Highlander, 2015-2016 Toyota Tundra, Scion FR-S, and tC vehicles. The Load Carrying Capacity Modification Label may not reflect the correct added weight of the installed accessories. As a result, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims for Passenger Cars."
Consequence & remedy
Consequence: An incorrect label may lead an owner to overload the vehicle, increasing the risk of a crash.
Remedy: SET will notify owners, and provide a corrected label for placement over the inaccurate label, free of charge. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Illustration