IllustrationFront Upper Grille Hood Scoop becomes loose and flys off during highway speeds and can distract a driver to the point of having an accident. Has been replaced once and is loose again held down by duck tape.
2018 Toyota Tundra
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2018 Toyota Tundra do not stand out strongly from the model-year median of 144.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Tundra years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
360–25K
625–50K
350–75K
275–100K
1100–150K
0150K+
48 reports with mileage · 51 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Fuel/propulsion System. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports3 fire reports4 injury reports
What owners actually said
99 reportsVehicle never been crash or hit by other car, but is showing problem with the air bag system
The upper grille and hood trim assembly on my 2018 Toyota Tundra 1794 Edition failed and partially detached from the vehicle due to apparent mounting clip and retainer failure. The failed component is available for inspection upon request. Photographs of the damage and detached trim assembly have been documented. This failure c…
Read full complaint
The upper grille and hood trim assembly on my 2018 Toyota Tundra 1794 Edition failed and partially detached from the vehicle due to apparent mounting clip and retainer failure. The failed component is available for inspection upon request. Photographs of the damage and detached trim assembly have been documented. This failure created a significant safety risk because the panel could have fully detached while the vehicle was in motion and become a roadway hazard to other motorists. The detached component also created concerns regarding possible interference with the front grille assembly and Toyota Safety Sense components located behind the grille area. Prior to the failure, there were no warning lamps, dashboard messages, or other electronic warnings indicating a problem. There were also no visible signs of impact damage or collision that would explain the failure. The condition appears to have occurred during normal vehicle operation. The vehicle currently has approximately 76,900 miles. After researching the issue, I identified multiple reports from other Toyota Tundra owners describing similar failures involving the upper grille garnish, mounting tabs, and retaining clips on this generation of Tundra vehicles. At this time, the issue has not yet been formally inspected by Toyota, law enforcement, insurance representatives, or an independent repair facility. Dealer confirmation is currently UNKNOWN. However, based on visual inspection, the mounting clips and retainers appear to have failed under normal operating conditions.
Sometimes the engine will randomly turn off while driving and become hard to restart like it’s not getting fuel.
Seat back on driver side caught fire burn 2" x 2" hole in the seat back
When starting up my truck in the morning there is rough idle that cause truck to sputter and sound horrible. It eventually smooths out but I believe the computer needs flashing. When I look online some have a recall for the engine 3UR-FBE / 2018 Toyota tundra, but when I put in my vin # it shows no recall and throws off check en…
Read full complaint
When starting up my truck in the morning there is rough idle that cause truck to sputter and sound horrible. It eventually smooths out but I believe the computer needs flashing. When I look online some have a recall for the engine 3UR-FBE / 2018 Toyota tundra, but when I put in my vin # it shows no recall and throws off check engine light Code. Also my radar sensor that it on for cruise control is showing up on dash please contact dealer and flashing. They have replaced this before with recall and now it’s acting up again. Also traction control is lighting up I. The dash as well blinking along with all these codes.
The vehicle was having issues with the fuel pump which was a known safety recall for the 2018 Toyota Tundra vehicles. The service man said that when he pulled up the safety recall for our VIN number that it didn't show anything, but we needed a new fuel pump according to the service codes that were coming up after inspection. T…
Read full complaint
The vehicle was having issues with the fuel pump which was a known safety recall for the 2018 Toyota Tundra vehicles. The service man said that when he pulled up the safety recall for our VIN number that it didn't show anything, but we needed a new fuel pump according to the service codes that were coming up after inspection. They made us pay for the fuel pump before we left the dealership. The vehicle was too dangerous to drive without having the work performed (getting stalled out or stuck on the highway) so we had to pay for the work. Toyota said that I could file a complaint with NHTSA to get my vehicle added to this recall and then try again for reimbursement. I have the repair paperwork if needed to support this claim.
Heated seat element and module burnt
I had an independent service center diagnose the issue with my 2018 Toyota Tundra. My truck would not start so there was no safety concern, but if the fuel pump failed while driving then the safety concern rises. The electrical connection inside the fuel pump was melted. There was no warning signs of the issue, it just would not…
Read full complaint
I had an independent service center diagnose the issue with my 2018 Toyota Tundra. My truck would not start so there was no safety concern, but if the fuel pump failed while driving then the safety concern rises. The electrical connection inside the fuel pump was melted. There was no warning signs of the issue, it just would not turn all the way over. I looked up that the 2018 Toyota Tundra w certain VIN #'s have a recall for the fuel pump, unfortunately my VIN # is not included.
The truck under frame is rusting a lot in spots near welds.
Official recalls
821V920000 · Steering:hydraulic Power Assist System; Steering:rack And Pinion
Nov 23, 2021
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Consequence & remedy
Consequence: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Additional source detail variants (2)
Steering:hydraulic Power Assist System
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Consequence: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Steering:rack And Pinion
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
Consequence: An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
21V688000 · Electrical System:wiring; Exterior Lighting:headlights
Sep 2, 2021
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2021 Tundra vehicles. The headlight electrical circuits may power the high and low beams simultaneously, which could overheat the electrical connector.
Consequence & remedy
Consequence: An overheated electrical connector can increase the risk of a fire.
Remedy: Dealers will modify the engine wire harness assembly and replace any damaged bulb, bulb connector, and/or headlight assembly as necessary, free of charge. Owner notification letters were mailed April 25, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB06 and 21TA06.
Additional source detail variants (2)
Exterior Lighting:headlights
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2021 Tundra vehicles. The headlight electrical circuits may power the high and low beams simultaneously, which could overheat the electrical connector.
Consequence: An overheated electrical connector can increase the risk of a fire.
Remedy: Dealers will modify the engine wire harness assembly and replace any damaged bulb, bulb connector, and/or headlight assembly as necessary, free of charge. Owner notification letters were mailed April 25, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB06 and 21TA06.
Electrical System:wiring
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2021 Tundra vehicles. The headlight electrical circuits may power the high and low beams simultaneously, which could overheat the electrical connector.
Consequence: An overheated electrical connector can increase the risk of a fire.
Remedy: Dealers will modify the engine wire harness assembly and replace any damaged bulb, bulb connector, and/or headlight assembly as necessary, free of charge. Owner notification letters were mailed April 25, 2022. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 21TB06 and 21TA06.
20V410000 · Electrical System:wiring; Exterior Lighting:turn Signal
Jul 15, 2020
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2020 Toyota Tundra vehicles equipped with LED headlight assemblies. Due to a wiring error, the front turn signals may not flash brightly enough. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: If the turn signals or hazard lamps do not flash brightly enough, other drivers may fail to see that the turn signal or hazard lamp functions have been activated, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will modify the wire harness connected to the front turn signal bulbs free of charge. The recall began August 17, 2020. Owners may contact Toyota customer service at 1-800-270-9371. Toyota's number for this recall is 20TB12/20TA12.
Additional source detail variants (2)
Exterior Lighting:turn Signal
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2020 Toyota Tundra vehicles equipped with LED headlight assemblies. Due to a wiring error, the front turn signals may not flash brightly enough. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: If the turn signals or hazard lamps do not flash brightly enough, other drivers may fail to see that the turn signal or hazard lamp functions have been activated, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will modify the wire harness connected to the front turn signal bulbs free of charge. The recall began August 17, 2020. Owners may contact Toyota customer service at 1-800-270-9371. Toyota's number for this recall is 20TB12/20TA12.
Electrical System:wiring
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2020 Toyota Tundra vehicles equipped with LED headlight assemblies. Due to a wiring error, the front turn signals may not flash brightly enough. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence: If the turn signals or hazard lamps do not flash brightly enough, other drivers may fail to see that the turn signal or hazard lamp functions have been activated, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will modify the wire harness connected to the front turn signal bulbs free of charge. The recall began August 17, 2020. Owners may contact Toyota customer service at 1-800-270-9371. Toyota's number for this recall is 20TB12/20TA12.
20V012000 · Fuel System, Gasoline:delivery:fuel Pump
Jan 13, 2020
Toyota Motor Engineering & Manufacturing (Toyota) recalled certain 2018-2019 4Runner, Highlander, Camry, Land Cruiser, Sequoia, Sienna, Tacoma and Tundra, and Lexus RC 300, RC 350, GS 350, GX 460, IS 300, LC 500, LS 500, LX 570, RX 350L, and 2019 Toyota Avalon and Corolla, and certain Lexus NX 300, and ES 350 vehicles on January 13, 2020. On March 4, 2020, Toyota expanded the recall to include certain 2014-2015 Toyota 4Runner and Land Cruiser, 2018 Avalon, Corolla, 2014 FJ Cruiser, 2017 Sienna and Lexus 2018 ES 350, 2018-2019 GS 300, 2013-2014 GS350, 2014-2015 GX 460, IS 350 and LX 570, 2014 IS F, 2018-2019 IS 350, LC 500H and LS 500H, 2013-2015 LS 460, 2015 NX 200T and RC350, 2017 RC 200T and RX 350. Toyota also removed the 2018-2019 Toyota 4Runner and Land Cruiser and 2018-2019 Lexus GX 460 and LX 570 and 2019 NX300 from inclusion in this recall. On March 19, 2020, Toyota expanded the recall to include 2015 Lexus GS350 vehicles. The low-pressure fuel pump inside the fuel tank may fail.
Consequence & remedy
Consequence: If the fuel pump fails, the engine can stall while driving, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will replace the fuel pump, free of charge. The recall began May 4, 2020. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are 20TB02 and 20TA02 for Toyota vehicles and 20LB01 and 20LA01 for Lexus vehicles.
18V711000 · Equipment:other:labels
Oct 11, 2018
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 Toyota Tundra vehicles. The accessory all-weather floormats may have been counted twice when creating the load carrying capacity modification label, resulting in the capacity modification label incorrectly overstating the additional weight by 10 pounds. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: Since the incorrect label is not within 1% of the additional weight, the vehicles are not compliant with the FMVSS.
Remedy: All vehicle owners will be sent a corrected label. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's number for this recall is J0Z.
18V685000 · Air Bags; Electrical System:software
Oct 4, 2018
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 Toyota Tundra and Sequoia vehicles and 2019 Toyota Avalon and Avalon Hybrid vehicles. The air bag electronic control unit (ECU) may erroneously detect a fault during the vehicle start-up self check. If this occurs, the ECU may not deploy the airbags as intended, in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection," and 214, "Side Impact Protection."
Consequence & remedy
Consequence: If the air bags do not deploy as intended, it can increase the risk of injury in a crash.
Remedy: Toyota will notify owners, and dealers will update the software for the air bag ECU, free of charge. The recall began October 26, 2018. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's number for this recall is J0X. Note: 18V-122 was superseded by this recall. The software remedy also includes the updates to the software for 18V-122.
Additional source detail variants (2)
Electrical System:software
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 Toyota Tundra and Sequoia vehicles and 2019 Toyota Avalon and Avalon Hybrid vehicles. The air bag electronic control unit (ECU) may erroneously detect a fault during the vehicle start-up self check. If this occurs, the ECU may not deploy the airbags as intended, in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection," and 214, "Side Impact Protection."
Consequence: If the air bags do not deploy as intended, it can increase the risk of injury in a crash.
Remedy: Toyota will notify owners, and dealers will update the software for the air bag ECU, free of charge. The recall began October 26, 2018. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's number for this recall is J0X. Note: 18V-122 was superseded by this recall. The software remedy also includes the updates to the software for 18V-122.
Air Bags
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018-2019 Toyota Tundra and Sequoia vehicles and 2019 Toyota Avalon and Avalon Hybrid vehicles. The air bag electronic control unit (ECU) may erroneously detect a fault during the vehicle start-up self check. If this occurs, the ECU may not deploy the airbags as intended, in the event of a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection," and 214, "Side Impact Protection."
Consequence: If the air bags do not deploy as intended, it can increase the risk of injury in a crash.
Remedy: Toyota will notify owners, and dealers will update the software for the air bag ECU, free of charge. The recall began October 26, 2018. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's number for this recall is J0X. Note: 18V-122 was superseded by this recall. The software remedy also includes the updates to the software for 18V-122.
18V122000 · Electronic Stability Control (esc)
Feb 20, 2018
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2018 Toyota Tundra and Sequoia vehicles. Electrical interference within the power supply circuit may cause the vehicle's electronic stability control system to be deactivated. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 126, "Electronic Stability Control Systems."
Consequence & remedy
Consequence: Deactivation of the vehicle stability control system can increase the risk of a crash in certain conditions.
Remedy: Toyota will notify owners, and dealers will update the vehicle's software, free of charge. The recall began March 14, 2018. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's number for this recall is J0H. Note: This recall has been superseded by 18V-685. The software remedy for 18V-685 includes the updates to the software for this recall.
17V831000 · Equipment:other:labels
Dec 20, 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2017-2018 Toyota 4Runner and Tundra, 2018 Toyota Highlander, RAV4 and Lexus GX460 and 2017 Toyota Sienna and Tacoma vehicles. These vehicles may have incorrect load carrying capacity modification labels. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An incorrect load information label can result in the operator overloading the vehicle and increasing the risk of a crash.
Remedy: Toyota will notify owners and provide them with corrected labels, free of charge. The recall began on January 23, 2018. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are H0Z for Toyota vehicles, and HLF for Lexus vehicles.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
0No exact-year investigations in this snapshot.