Vehicle was sold by Westgate Crysler Jeep Dodge Ram of Raleigh with missing caliper bolt in front passenger brake system. This was detected by an independent service center while getting brake pads and rotors replaced, as they were very worn and causing the brake system to be jumpy and catchy, despite Westgate assuring they wer…
Read full complaint
Vehicle was sold by Westgate Crysler Jeep Dodge Ram of Raleigh with missing caliper bolt in front passenger brake system. This was detected by an independent service center while getting brake pads and rotors replaced, as they were very worn and causing the brake system to be jumpy and catchy, despite Westgate assuring they were fine. The lack of the bolt in the caliper put my entire family's life at risk from the second we drove off the lot a little over a month ago.
NHTSA ODI #11753994
Mileage unknown · Mar 10, 2023
Service BrakesCrashInjury
Brake system Seatbelt came out of latch Approaching a red light and stopped traffic, applied brakes and no response. Ended up rear ending another vehicle. Resulting in injury to driver of malfunctioning vehicle and possible injuries to other passengers in the other vehicle . Don’t know if the vehicle is available. It was deem…
Read full complaint
Brake system Seatbelt came out of latch Approaching a red light and stopped traffic, applied brakes and no response. Ended up rear ending another vehicle. Resulting in injury to driver of malfunctioning vehicle and possible injuries to other passengers in the other vehicle . Don’t know if the vehicle is available. It was deemed totaled. It’s Unkown if there’s been any inspections as of yet. There was some kind of audible notification that occurred when driver applied brakes right before collision
NHTSA ODI #11511144
16,000 miles · Jun 29, 2021
Electrical SystemService Brakes
The contact owns a 2019 Dodge Charger. The contact stated the automatic braking system had been engaging inadvertently while driving with the brake warning light illuminated. The vehicle was taken to the dealer several times for diagnosis; however, the dealer was unable to duplicate the failure. The contact also stated that the …
Read full complaint
The contact owns a 2019 Dodge Charger. The contact stated the automatic braking system had been engaging inadvertently while driving with the brake warning light illuminated. The vehicle was taken to the dealer several times for diagnosis; however, the dealer was unable to duplicate the failure. The contact also stated that the electrical system had been malfunctioning, causing the instrument panel to become inoperable. The manufacturer was made aware of the failure but provided no assistance. The vehicle was not repaired. The approximate failure mileage was 16,000.
NHTSA ODI #11422796
32,300 miles · Mar 9, 2021
Service BrakesUnknown Or Other
WHEN GO OVER 30 AND BRAKE THE CAR SHAKES BUT UNDER THEM SPEED NOTHING HAPPENS ITS REGULAR. JUST BOUGHT THE CAR 2 WEEKS AGO.
NHTSA ODI #11399871
20 miles · Oct 12, 2020
Service Brakes
I PURCHASED A NEW 2019 DODGE CHARGER SCATPACK. IT WAS PURCHASED AS A LEISURE CAR FOR WEEKEND USE. I'VE HAD THE VEHICLE FOR A YEAR AND A HALF AND HAS 13000 MILES. THE VEHICLE BEGAN TO SHIMMY FROM THE FRONT BRAKES. THE FRONT VIBRATION BEGAN VERY LIGHT BUT HAS CONTINUED TO INCREASE. AT FIRST I BELIEVE THAT IT WAS PROBABLY CAUSED B…
Read full complaint
I PURCHASED A NEW 2019 DODGE CHARGER SCATPACK. IT WAS PURCHASED AS A LEISURE CAR FOR WEEKEND USE. I'VE HAD THE VEHICLE FOR A YEAR AND A HALF AND HAS 13000 MILES. THE VEHICLE BEGAN TO SHIMMY FROM THE FRONT BRAKES. THE FRONT VIBRATION BEGAN VERY LIGHT BUT HAS CONTINUED TO INCREASE. AT FIRST I BELIEVE THAT IT WAS PROBABLY CAUSED BY THE FACT THAT IT WAS NOT DRIVEN TO OFTEN AND THERE WAS PROBABLY A RUST BUILDUP OF SOME KIND. HOWEVER, IN RESEARCHING THE INTERNET IT APPEARS TO BE A COMMON PROBLEM WITH THIS VEHICLE. THE DEALERSHIP LABELED THE PROBLEM AS A WEAR AND TEAR ISSUE AND FOR THAT REASON IT WOULD BE MY RESPONSIBILITY TO FIX IT. I STRONGLY BELIEVE THAT THIS IS A POOR DESIGNED PROBLEM THAT THE MANUFACTURER IS REFUSING TO RECOGNIZE. I'VE OWNED MANY CARS IN MY 58 YEAR'S OF LIFE AND I KNOW THAT A BREAK ISSUE UNFORTUNATELY TAKES LOSS OF LIFE BEFORE IT'S ADDRESSED BY THE AUTHORITIES AND OR MANUFACTURER'S. I'M HOPING THAT THESE ISSUE IS ADDRESSED AS I'VE FOUND THROUGHOUT MY RESEARCH THAT IT'S A COMMON PROBLEM WITH THIS VEHICLE AND IT COMES WITH OTHER PROBLEMS LIKE BRAKE FAILURE ALSO. THE BRAKES ARE MANUFACTURED BY BREMBO BRAKE WHO HAS ALSO REFUSED TO ACKNOWLEDGE A POSIBLE PROBLEM WITH THE BRAKES.
NHTSA ODI #11364007
10,000 miles · Oct 4, 2020
Air BagsElectrical SystemService Brakes
CENSORS KEEP FLASHING OUT OF CONTROL ON AND OFF BRAKES HAVE BEEN MESSED UP SINCE DAY ONE AIR BAG CENSOR KEEPS GOING ON
NHTSA ODI #11362601
3,500 miles · May 15, 2020
Service Brakes
2019 DODGE CHARGER SCATPACK WITH BREMBO BRAKES. REAR BRAKE PADS ONLY COVERING 80% OF ROTOR. OUTER EDGES OF EACH REAR ROTOR ARE UNTOUCHED BY THE OEM BREMBO BRAKE PAD. *TR
NHTSA ODI #11324731
Mileage unknown · May 4, 2020
Service BrakesSteeringWheels
I TOOK MY CAR TO GET A OIL CHANGE AT THE DODGE DEALERSHIP. WHEN IT WAS RETURNED TO ME I NOTICE THAT WHEN I TURN MY WHEEL ALL THE WAY TO A CERTAIN SIDE IT MAKES A LOUD RUBBING NOISE. THEY ROTATED MY TIRES AND CHANGED MY FLUIDS SO I BELIEVE IT WOULD EVENTUALLY GO AWAY. IT HASN'T
NHTSA ODI #11323222
800 miles · Feb 4, 2020
Service Brakes
THE REAR BRAKE PADS DO NOT SWEEP THE ENTIRE SURFACE OF THE REAR ROTORS. NEARLY 25% OF THE REAR ROTOR IS NOT IN CONTACT WITH THE REAR BRAKE PADS. THIS DIMINISHES BRAKING FORCE AND MAKES THE REAR ROTOR INCOMPATIBLE WITH CURRENTLY AVAILABLE REPLACEMENT PADS. THIS DEFECT IS VISUALLY APPARENT WHEN THE CAR IS STATIONARY. IT ALSO IMPAC…
Read full complaint
THE REAR BRAKE PADS DO NOT SWEEP THE ENTIRE SURFACE OF THE REAR ROTORS. NEARLY 25% OF THE REAR ROTOR IS NOT IN CONTACT WITH THE REAR BRAKE PADS. THIS DIMINISHES BRAKING FORCE AND MAKES THE REAR ROTOR INCOMPATIBLE WITH CURRENTLY AVAILABLE REPLACEMENT PADS. THIS DEFECT IS VISUALLY APPARENT WHEN THE CAR IS STATIONARY. IT ALSO IMPACTS THE VEHICLES ABILITY TO COME TO A STOP WHILE IN MOTION. I SUSPECT THAT THE WRONG PARTS WERE INSTALLED BY THE MANUFACTURER OR THERE IS A MANUFACTURING DEFECT PRESENT.
NHTSA ODI #11306986
1,500 miles · Jan 28, 2020
Service Brakes
THE REAR BRAKE PADS DO NOT FIT CORRECTLY, THEY ARE UNDERSIZED. THERE IS A LARGE PORTION OF THE REAR ROTOR THAT IS NOT IN CONTACT WITH THE PAD. THIS IS CAUSING DAMAGE AND PREMATURE WEAR TO THE BRAKE ROTORS.
Chrysler (FCA US, LLC) (Stellantis) is recalling certain 2018-2021 Dodge Charger and Chrysler 300 vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury or death.
Remedy: Dealers will replace both side curtain air bags, free of charge. Owner notification letters were mailed beginning February 20, 2025. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 19B.
Chrysler (FCA US LLC) is recalling certain 2018-2020 Dodge Charger Pursuit vehicles equipped with a "stealth mode." When stealth mode is selected, the backup camera rearview image will not display when the vehicle is in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rearview Mirrors."
Consequence & remedy
Consequence: The lack of a back-up camera display increases the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will update body control module software to disable stealth mode when the vehicle is shifted into "Reverse", free of charge. The recall began October 22, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W62.
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence & remedy
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Additional source detail variants (3)
Service Brakes
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Wheels
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Tires
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Charger vehicles. The driver and passenger sun visors may lack the required air bag warning information. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Consequence & remedy
Consequence: Failure to provide the air bag warning information increases the risk of injury.
Remedy: Chrysler has notified owners, and dealers will replace the driver and passenger sun visors, free of charge. The recall began April 17, 2019. Owners may contact FCA US customer service at 1-800-853-1403. Chrysler's number for this recall is V35.
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger and Chrysler 300 vehicles. The instrument cluster may not properly illuminate driver warnings. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."
Consequence & remedy
Consequence: Failure of the instrument cluster to properly illuminate may prevent the driver from receiving warnings about the vehicle's systems, increasing the risk of crash.
Remedy: Chrysler has notified owners, and dealers will update the instrument cluster software, free of charge. The recall began April 8, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V32.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2019 Dodge Charger Problems, Complaints & Recalls | Skip That Year
Illustration