On January 6, 2025, Countryside CDJR in Georgia performed internal engine repairs on my 2019 Dodge Charger R/T, including lifter and internal engine work. Only months later, the engine suffered a catastrophic failure while driving. The vehicle became disabled and had to be towed. This raises serious concerns of improper repair …
Read full complaint
On January 6, 2025, Countryside CDJR in Georgia performed internal engine repairs on my 2019 Dodge Charger R/T, including lifter and internal engine work. Only months later, the engine suffered a catastrophic failure while driving. The vehicle became disabled and had to be towed. This raises serious concerns of improper repair or a safety-related engine defect. The dealership denies responsibility and blames a single missed oil change. A single missed oil change does not cause sudden catastrophic engine failure so soon after dealership-performed internal work. This could be related to known 5.7L HEMI lifter/camshaft issues. I am requesting that NHTSA review this failure for potential safety defect or incorrect repair contributing to engine failure.
NHTSA ODI #11698261
Mileage unknown · Sep 15, 2023
Engine
Vehicle purchased new, maintained per the owners manual and radiator requires replaced due to manufacturers defect.
NHTSA ODI #11544688
Mileage unknown · Apr 20, 2023
Electrical SystemEngineFuel/propulsion SystemFire
The 2019 Dodge Charger, a police vehicle, was enroute to a crash scene when it caught fire. The fire appears to have originated in the engine compartment near the fire wall.
NHTSA ODI #11518011
Mileage unknown · Feb 9, 2023
Engine
Oil cooler assembly leaking oil onto road when driving. No warning lights pop up on dash to inform.Part have been inspect by professional car dealership.
NHTSA ODI #11506498
Mileage unknown · Feb 19, 2022
Engine
Outside temp was around 32F. Drove normally for 15 minutes and came to a stop. Was idling approximately two minutes and temperature gauge started climbing rapidly. High fans turned on but temps continued to climb. Turned off engine for a few mins and temps were okay. Took it to a garage the next morning and mechanic said the r…
Read full complaint
Outside temp was around 32F. Drove normally for 15 minutes and came to a stop. Was idling approximately two minutes and temperature gauge started climbing rapidly. High fans turned on but temps continued to climb. Turned off engine for a few mins and temps were okay. Took it to a garage the next morning and mechanic said the radiator was broken.
NHTSA ODI #11452935
7,000 miles · Feb 1, 2021
EngineFire
TL* THE CONTACT OWNS A 2019 DODGE CHARGER. THE CONTACT STATED WHILE THE VEHICLE WAS AT A STAND STILL, SHE SAW BLACK/BLUE SMOKE EXITING FROM THE REAR AND STATED THE VEHICLE BEGAN SHAKE AND MAKE AN ABNORMAL NOISE. THE CONTACT STATED NO WARNING LIGHTS WERE ILLUMINATED AT THE MOMENT. THE CONTACT STATED DAYS LATER, THE CHECK ENGINE W…
Read full complaint
TL* THE CONTACT OWNS A 2019 DODGE CHARGER. THE CONTACT STATED WHILE THE VEHICLE WAS AT A STAND STILL, SHE SAW BLACK/BLUE SMOKE EXITING FROM THE REAR AND STATED THE VEHICLE BEGAN SHAKE AND MAKE AN ABNORMAL NOISE. THE CONTACT STATED NO WARNING LIGHTS WERE ILLUMINATED AT THE MOMENT. THE CONTACT STATED DAYS LATER, THE CHECK ENGINE WARNING LIGHT ILLUMINATED. THE VEHICLE WAS TAKEN TO LOCAL DEALER CARL HOGAN CHEVROLET BUICK GMC (2333 HWY 45 N, COLUMBUS, MS 39705: (662) 580-0726), AND WAS MADE AWARE OF THE FAILURE. THE CONTACT CALLED THE DEALER WHERE SHE PURCHASED THE VEHICLE AND WAS TOWED TO THEIR FACILITY. THE VEHICLE HAD NOT BEEN DIAGNOSED OR REPAIRED. THE MANUFACTURER HAD BEEN INFORMED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 7,000.
NHTSA ODI #11390982
25 miles · Jan 2, 2021
Engine
I JUST BOUGHT THIS CAR 6 MONTHS AGO 2ND OWNER AS I START THE CARIBBEAN COULD HEAR THE LIFTERS IN THE ENGINE THE CAR ONLY HAS 42000 MILES IVE OWNED A2013 CHARGER AND IT PRETTY MUCH HAD SAME PROBLEM DEALER FIXED
NHTSA ODI #11386173
16,000 miles · Oct 19, 2020
Engine
I WAS DRIVING THE CAR JUST SHUT DOWN COMPLETELY AND WOULDN'T CRANK WITHOUT WARNING OR ANYTHING.
NHTSA ODI #11365245
Mileage unknown · Sep 19, 2020
Engine
I HAVE A ENGINE PROBLEM WITH MY CAR WHICH IS COMES UNDER WARRANTY I WENT TO THE DEALERSHIP THEY TOLD ME I STILL HAVE TO PAY FOR EVERYTHING I JUST BOUGHT MY CAR THIS YEAR THE ENGINE JUST SHUT DOWN ON THE ROAD WITHOUT ANY REASON. IT DIDN'T GIVE ANY WARNING
Chrysler (FCA US, LLC) (Stellantis) is recalling certain 2018-2021 Dodge Charger and Chrysler 300 vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury or death.
Remedy: Dealers will replace both side curtain air bags, free of charge. Owner notification letters were mailed beginning February 20, 2025. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 19B.
Chrysler (FCA US LLC) is recalling certain 2018-2020 Dodge Charger Pursuit vehicles equipped with a "stealth mode." When stealth mode is selected, the backup camera rearview image will not display when the vehicle is in reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rearview Mirrors."
Consequence & remedy
Consequence: The lack of a back-up camera display increases the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will update body control module software to disable stealth mode when the vehicle is shifted into "Reverse", free of charge. The recall began October 22, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W62.
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence & remedy
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Additional source detail variants (3)
Service Brakes
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Wheels
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Tires
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Charger vehicles. The driver and passenger sun visors may lack the required air bag warning information. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Consequence & remedy
Consequence: Failure to provide the air bag warning information increases the risk of injury.
Remedy: Chrysler has notified owners, and dealers will replace the driver and passenger sun visors, free of charge. The recall began April 17, 2019. Owners may contact FCA US customer service at 1-800-853-1403. Chrysler's number for this recall is V35.
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger and Chrysler 300 vehicles. The instrument cluster may not properly illuminate driver warnings. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."
Consequence & remedy
Consequence: Failure of the instrument cluster to properly illuminate may prevent the driver from receiving warnings about the vehicle's systems, increasing the risk of crash.
Remedy: Chrysler has notified owners, and dealers will update the instrument cluster software, free of charge. The recall began April 8, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V32.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2019 Dodge Charger Problems, Complaints & Recalls | Skip That Year
Illustration