2014 BMW X3

Electrical System:wiring:connectors/plugs/receptacles

BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.

Consequence: An electrical short increases the risk of a fire.

Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.

Engine And Engine Cooling:cooling System:pump

BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.

Consequence: An electrical short increases the risk of a fire.

Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.

Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings

BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.

Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.

Service Brakes, Hydraulic:power Assist:vacuum

BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.

Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.

Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings

BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.

Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.

Service Brakes, Hydraulic:power Assist:vacuum

BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.

Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.