IllustrationTHE VOLVO VN HEAVY DUTY TRUCKS HAVE A LOW BEAM LIGHTING SYSTEM THAT IS TOTALLY INADEQUATE. THESE LIGHTS ARE MUCH TOO DIM AND WHEN THE DEALERSHIPS ARE CONFRONTED WITH THIS, THEY ONLY WANT TO SELL AN ENTIRE NEW LIGHTING UNIT. NO ONE SEEMS TO KNOW WHAT THE PROBLEM IS AND THE COMPANY SEEMS TO BE USING THIS AS A "CASH COW".
2005 Volvo Vn
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Vn years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 0 of 2 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Exterior Lighting. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
2 reportsTL*THE CONTACT OWNS A 2005 VOLVO VN. THE TRACTOR TRAILERS DID NOT HAVE CIRCUIT BREAKERS WHICH CAUSED THE FUSE TO BLOW AND THE BRAKE LIGHT NOT TO ILLUMINATE. THE CONTACT WAS AWARE OF THE SAFETY RISK INVOLVED. THE MILEAGE WAS UNKNOWN. *AK
Official recalls
212V510000 · Seat Belts
Oct 18, 2012
Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: In the event of a crash, an insufficient seat belt weld may prevent the seat belt from properly restraining the occupant. This increases the risk of injury to the seat occupant.
Remedy: Volvo Trucks of America will notify owners, and dealers will replace the suspected d-ring, free of change. The safety recall began on May 10, 2013. Owners may contact Volvo at 1-336-393-2000.
05V311000 · Suspension
Jul 7, 2005
ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS, EQUIPPED WITH HOLLAND AIR SUSPENSION SYSTEMS, A TRANSVERSE BEAM CASTING MAY FRACTURE UNDER NORMAL LOADS. IF A CASTING BREAKS WHEN THE VEHICLE IS TRAVELING ON A ROADWAY THERE IS THE POTENTIAL FOR PIECES OF THE CASTING TO BECOME PROJECTILES AND THE SUSPENSION?S TRANSVERSE BEAM MAY DROP DOWN LOW ENOUGH TO CONTACT THE ROAD SURFACE.
Consequence & remedy
Consequence: THIS WILL CAUSE SPARKS THAT COULD POTENTIALLY IGNITE AND CAUSE A FIRE.
Remedy: DEALERS WILL INSPECT AND REPLACE THE DEFECTIVE TRANSVERSE BEAM ASSEMBLIES. THE RECALL BEGAN ON AUGUST 26, 2005. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3RQ11001 · Volvo Sleeper Glass de-bonding
Opened May 23, 2011 · Closed Jan 20, 2012
Status: closed (inferred from source dates) · Visibility:glass, Side/rear
ODI opened Recall Query RQ11-001 after a review of EWR Field Reports identified lower bunk window separations on the subject vehicles.Volvo had issued three recalls for sleeper window separations since 2003.Additionally, Volvo had issued two bulletins for sleeper window issues during the same time period.The frequency of related actions led ODI to open this formal investigation.An Information Request (IR) letter was sent to Volvo on 23 June 2011.Volvo responded on 17 August 2011 and then provided updated warranty information on 9 January 2012.Volvo provided production change data and warranty information which was correlated to vehicle build month and failure date.ODI analyzed the data to determine if additional production time frames should have been included in previous recalls.ODI also requested information from its network of fleet owners.The response from this network reaffirmed the accuracy of the updated warranty information.Based on the information and data received, ODI has concluded that all production periods have been appropriately addressed by Volvo's previous recalls and no additional recall action is required at this time.
EA09003 · Drag Link Failure
Opened Jan 15, 2009 · Closed Jul 6, 2010
Status: closed (inferred from source dates) · Steering; Steering:gear Box:shaft Pitman; Steering:gear Box:shaft Sector; Steering:linkages; Steering:linkages:drag:link:connection; Steering:linkages:drag:power Assist System; Steering:linkages:knuckle:spindle:arm
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Additional source detail variants (7)
Steering:gear Box:shaft Pitman
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Steering:gear Box:shaft Sector
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Steering:linkages:drag:link:connection
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Steering:linkages:drag:power Assist System
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Steering:linkages:knuckle:spindle:arm
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Steering:linkages
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
Steering
EA09-003 is closed with the submission of Volvo's recall 10V-282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V-282 in response to NHTSA's recall request letter dated June 3, 2010 (available at NHTSA's web site www.safercar.gov). NHTSA found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that NHTSA was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.
PE08053 · Drag Link Failure
Opened Sep 12, 2008 · Closed Jan 15, 2009
Status: closed (inferred from source dates) · Steering; Steering:linkages; Steering:linkages:drag:link:connection
ODI HAS DECIDED TO UPGRADE THIS PE AND CONDUCT FIELD WORK AND TESTING.SUMMARY NUMBERS IN THIS RESUME ARE REPRESENATIVE OF ONLY THE 2005 MODEL YEAR VEHICLES. SEE THE ATTACHED REPORT FOR DETAILS.
Additional source detail variants (3)
Steering:linkages:drag:link:connection
ODI HAS DECIDED TO UPGRADE THIS PE AND CONDUCT FIELD WORK AND TESTING.SUMMARY NUMBERS IN THIS RESUME ARE REPRESENATIVE OF ONLY THE 2005 MODEL YEAR VEHICLES. SEE THE ATTACHED REPORT FOR DETAILS.
Steering:linkages
ODI HAS DECIDED TO UPGRADE THIS PE AND CONDUCT FIELD WORK AND TESTING.SUMMARY NUMBERS IN THIS RESUME ARE REPRESENATIVE OF ONLY THE 2005 MODEL YEAR VEHICLES. SEE THE ATTACHED REPORT FOR DETAILS.
Steering
ODI HAS DECIDED TO UPGRADE THIS PE AND CONDUCT FIELD WORK AND TESTING.SUMMARY NUMBERS IN THIS RESUME ARE REPRESENATIVE OF ONLY THE 2005 MODEL YEAR VEHICLES. SEE THE ATTACHED REPORT FOR DETAILS.