← New search

2009 Toyota Highlander Hybrid

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

34 reports with mileage · 6 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Service Brakes. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes, Electric. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes, Hydraulic. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

2 crash reports0 fire reports1 injury reports

Engine complaints

4 reports
Clear category filter
124,842 miles · Jun 18, 2019
EngineService Brakes

TL* THE CONTACT OWNS A 2009 TOYOTA HIGHLANDER HYBRID. WHILE DRIVING UP A HILL AT 20 MPH, THE VEHICLE STALLED AND THE ABS, TRACTION CONTROL, STEERING SYSTEM, AND BATTERY WARNING INDICATORS ILLUMINATED. IN ADDITION, "STOP VEHICLE IN A SAFE PLACE IMMEDIATELY" APPEARED ON THE INSTRUMENT PANEL. THE CONTACT HAD TO DEPRESS THE BRAKE PE…

Read full complaint

TL* THE CONTACT OWNS A 2009 TOYOTA HIGHLANDER HYBRID. WHILE DRIVING UP A HILL AT 20 MPH, THE VEHICLE STALLED AND THE ABS, TRACTION CONTROL, STEERING SYSTEM, AND BATTERY WARNING INDICATORS ILLUMINATED. IN ADDITION, "STOP VEHICLE IN A SAFE PLACE IMMEDIATELY" APPEARED ON THE INSTRUMENT PANEL. THE CONTACT HAD TO DEPRESS THE BRAKE PEDAL WITH EXCESSIVE FORCE TO STOP THE VEHICLE. THE CONTACT COASTED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND HAD IT TOWED HOME. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE FAILURE RECURRED AND THE VEHICLE WAS TAKEN TO ROYAL SOUTH TOYOTA (LOCATED AT 3115 S WALNUT ST, BLOOMINGTON, IN 47401, (812) 331-1100) WHERE IT WAS DIAGNOSED, BUT NO FAILURE CODE WAS FOUND. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 124,842.

NHTSA ODI #11220968

125,000 miles · Nov 2, 2015
EngineHybrid Propulsion System

TL* THE CONTACT OWNS A 2009 TOYOTA HIGHLANDER HYBRID. WHILE DRIVING 30 MPH, THE CONTACT HEARD A CLUNKING NOISE COMING FROM THE FRONT END OF THE VEHICLE. THE VEHICLE LOST POWER AND FAILED TO ACCELERATE OR RESTART. THE VEHICLE WAS TOWED TO THE DEALER. THE DEALER IMMEDIATELY NOTICED THAT THE VEHICLE SEEMED TO CONSUME ABNORMAL QUANT…

Read full complaint

TL* THE CONTACT OWNS A 2009 TOYOTA HIGHLANDER HYBRID. WHILE DRIVING 30 MPH, THE CONTACT HEARD A CLUNKING NOISE COMING FROM THE FRONT END OF THE VEHICLE. THE VEHICLE LOST POWER AND FAILED TO ACCELERATE OR RESTART. THE VEHICLE WAS TOWED TO THE DEALER. THE DEALER IMMEDIATELY NOTICED THAT THE VEHICLE SEEMED TO CONSUME ABNORMAL QUANTITIES OF OIL. THE VEHICLE HAD AN OIL CHANGE A MONTH AND A HALF PRIOR TO THE FAILURE AND THE OIL METER MEASURED ONE QUART OF ENGINE OIL LEFT IN THE VEHICLE. THE DEALER WAS UNABLE TO DIAGNOSE THE FAILURE. SEVERAL MONTHS LATER, THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 13V396000 (HYBRID PROPULSION SYSTEM). AFTER THE RECALL REPAIR WAS PERFORMED, THE FAILURE RECURRED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 125,000. THE VIN WAS NOT AVAILABLE.

NHTSA ODI #10787806

57,780 miles · Sep 21, 2013
Engine

DRIVING ABOUT 40MPH WENT TO ACCELERATE AND THE WHOLE CAR STOPPED RESPONDING TO ANYTHING. COULDN'T DRIVE IT AT ALL, WAS ABLE TO LIMP TO SIDE OF ROAD, AT FIRST COULDN'T TURN VEHICLE OFF. ONCE ABLE TO TURN OFF AND BACK ON CAR WOULD DRIVE. WARNING MESSAGES CAME ON "CHECK BRAKE SYSTEM-HAVE YOUR VEHICLE CHECKED BY DEALER IMMEDIATELY" …

Read full complaint

DRIVING ABOUT 40MPH WENT TO ACCELERATE AND THE WHOLE CAR STOPPED RESPONDING TO ANYTHING. COULDN'T DRIVE IT AT ALL, WAS ABLE TO LIMP TO SIDE OF ROAD, AT FIRST COULDN'T TURN VEHICLE OFF. ONCE ABLE TO TURN OFF AND BACK ON CAR WOULD DRIVE. WARNING MESSAGES CAME ON "CHECK BRAKE SYSTEM-HAVE YOUR VEHICLE CHECKED BY DEALER IMMEDIATELY" AND THEN "CHECK HYBRID SYSTEM-STOP THE VEHICLE IN A SAFE PLACE (AS IF I HAD A CHOICE SINCE THE VEHICLE STOPPED ITSELF0, IMMEDIATELY CONTACT DEALER" HAD IT TOWED TO DEALER WHO DID A CHECK AND INFORMED ME THAT THE PROBLEM IS A PART OF THE MOST RECENT RECALL HOWEVER THEY DO NOT HAVE THE PARTS AS OF YET AND ARENT SURE WHEN THEY ARE GOING TO GET THEM.

NHTSA ODI #10544729

60,200 miles · Oct 15, 2012
Electrical SystemEnginePower Train

DEPRESSED ACCELERATOR AFTER BEING STOPPED AT TRAFFIC LIGHT. CAR JERKED FORWARD, STOPPED AND WOULD NOT RESTART. WARNING MESSAGES FOR THE HYBRID SYSTEM (MESSAGE WAS 'STOP IMMEDIATELY AND NOTIFY DEALER'), BRAKE SYSTEM AND 4 WHEEL DRIVE. CAR WAS TOWED TO DEALER WHO DETERMINED IT WAS FAILURE OF HYBRID INVERTER REQUIRING COMPLETE R…

Read full complaint

DEPRESSED ACCELERATOR AFTER BEING STOPPED AT TRAFFIC LIGHT. CAR JERKED FORWARD, STOPPED AND WOULD NOT RESTART. WARNING MESSAGES FOR THE HYBRID SYSTEM (MESSAGE WAS 'STOP IMMEDIATELY AND NOTIFY DEALER'), BRAKE SYSTEM AND 4 WHEEL DRIVE. CAR WAS TOWED TO DEALER WHO DETERMINED IT WAS FAILURE OF HYBRID INVERTER REQUIRING COMPLETE REPLACEMENT. I'M CONCERNED BECAUSE THIS SOUND SIMILAR TO ISSUES REPORTED FOR 2006 AND 2007 HIGHLANDER MODELS. *TR

NHTSA ODI #10480201

Official recalls

4

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

13V396000 · Hybrid Propulsion System: Inverter

Sep 4, 2013

Toyota is recalling certain model year 2006-2010 Highlander hybrid vehicles manufactured February 16, 2005, through July 29, 2010; and model year 2006-2008 Lexus RX400h vehicles manufactured February 23, 2005, through December 2, 2008. The Intelligent Power Module (IPM) inside the inverter module may contain transistors that have higher operating temperatures than the solder can support and the transistors may be heat damaged by the solder. If this occurs, various warning lamps, including the malfunction indicator lamp, slip indicator light, brake system warning light, and master warning light, will be illuminated on the instrument panel.

Consequence & remedy

Consequence: The vehicle may enter a fail-safe/limp-home mode that limits the drivability of the vehicle. It is possible that the hybrid system will shut down while the vehicle is being driven, causing the vehicle to stall unexpectedly, increasing the risk of a crash.

Remedy: Toyota will notify owners, and dealers will replace the IPM free of charge. Owners may contact Toyota at 1-800-331-4331. Vehicles that had their IPM replaced under recall 11V-342 are not affected by this campaign.

13V014000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seats

Jan 16, 2013

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

Consequence & remedy

Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.

Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

Additional source detail variants (2)

Seats

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.

Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

Air Bags:frontal:sensor/control MODULE-INACTIVE

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.

Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

09V223000 · Equipment:other:labels

Jun 15, 2009

TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."

Consequence & remedy

Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.

Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

3

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

EA18006 · Steering Column Separation

Opened Nov 16, 2018 · Closed Apr 2, 2024

Status: closed (inferred from source dates) · Steering; Steering:column

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Additional source detail variants (2)

Steering:column

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Steering

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

PE18005 · Upper Steering Column Separation

Opened May 4, 2018 · Closed Nov 20, 2018

Status: closed (inferred from source dates) · Steering; Steering:column

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

Additional source detail variants (2)

Steering:column

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

Steering

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.