Steering did not return to neutral position after making a right turn, steering wanted to continue on right turn. I was able to pull it back to straight position with some needed force. I don't believe my wife would be able , after initial surprise, to steer back into lane of traffic. Result could have been an accident. I have n…
Read full complaint
Steering did not return to neutral position after making a right turn, steering wanted to continue on right turn. I was able to pull it back to straight position with some needed force. I don't believe my wife would be able , after initial surprise, to steer back into lane of traffic. Result could have been an accident. I have not reproduced the problem at dealer or independent service facility or by manufacturer and because of no accident police or insurance co. not called. There were no warning signs. I just recently pudchased this vehicle within past week. I would call your attention to the articles on internet describing the problem and how to repair I don't think I should pay for repair as it is a recurring problem with other cars by same manufacturer. Thank you
NHTSA ODI #11527329
Mileage unknown · Apr 28, 2021
Steering
I'M HAVING ISSUES WITH THE STEERING COLUMN AND GETTING THE KEY OUT. I'M NOT ABLE TO REMOVE THE KEY MOST DAYS. WAS THIS IN ANY PART OF ANY KNOWN RECALL? THANK YOU
NHTSA ODI #11414333
20,500 miles · Apr 11, 2021
SteeringUnknown Or Other
KEY GETS STUCK IN IGNITION. OFTEN WILL NOT RELEASE. HAPPENS WHEN PUT CAR INTO PARK UPON STOPPING.
NHTSA ODI #11407477
58,814 miles · Dec 28, 2020
SteeringUnknown Or Other
EXPERIENCED DIFFICULTY REMOVING KEY FROM IGNITION AFTER VEHICLE IS STOPPED AND ENGINE TURNED OFF. ISSUE RECURS FREQUENT BUT RANDOMLY. SOMETIMES IT REQUIRE SEVERAL ATTEMPTS TO RESTART AND SHUT-OFF ENGINE BEFORE KEY WOULD RELEASE FROM IGNITION. VEHICLE WAS RETURNED TO DEALER FOR REPAIR AND FAULTY PART IN SHIFTER ASSEMBLY REPLACED.
NHTSA ODI #11385364
150,000 miles · Oct 2, 2020
Steering
KEY DOES NOT COME OUT OF IGNITION AFTER PUTTING CAR IN PARK
NHTSA ODI #11362409
34,000 miles · Jun 22, 2020
Electrical SystemSteering
AM ABLE TO SHIFT INTO PARK AND TURN OFF THE IGNITION BUT NOT ABLE TO REMOVE KEY. IT TAKES SEVERAL TRIES TO SHIFT GEARS UNTIL ABLE TO TURN THE KEY TO RELEASE IT. THIS WAS HAPPENING FOR A WHILE AND STOPPED AND HAS STARTED DOING IT MORE CONSISTENTLY NOW. *TR
NHTSA ODI #11330179
Mileage unknown · Dec 19, 2019
Steering
KEY WILL NOT REMOVE FROM IGNITION WHEN TURNING OFF CAR. PROGRESSIVELY GOT MORE FREQUENT. ONLY WAY TO REMOVE THE KEY IS TO MOVE THE CAR OR TO SHIFT BACK IN FORTH FROM PARK TO DRIVE. PART HAD TO BE REPLACED
NHTSA ODI #11290031
55,000 miles · Dec 6, 2019
SteeringUnknown Or Other
UNABLE TO REMOVE KEY FROM IGNITION WHEN VEHICLE IS IN PARK-ENGINE/CAR TURNS OFF EXCEPT RADIO/LIGHTS. HAVE TO RESTART CAR PUT INTO REVERSE, BACK INTO PARK, THEN TURN OFF CAR.
NHTSA ODI #11287462
31,000 miles · Nov 13, 2019
SteeringUnknown Or Other
HAVING DIFFICULTY REMOVING KEY FROM IGNITION WHEN VEHICLE IS IN PARK - CAR WILL TURN OFF BUT CANNOT REMOVE THE KEY WITHOUT MUCH DIFFICULTY, RESTARTING JIGGLING WITH FORCE - FEAR OF KEY BREAKING IN IGNITION
NHTSA ODI #11279802
18,000 miles · Apr 1, 2019
Electronic Stability Control (esc)SteeringCrash
MAY OF 2017 I WAS DRIVING NORTH BOUND ON 294. AS I WAS GOING THROUGH THE CURVE THE POWER STEERING LIGHT CAME ON THE CAR WOULDN'T TURN BACK. I STOP AND WAS ABLE TO PULL THE CAR OFF THE ROAD WITH NO INCIDENT. I CALLED SIS IT'S A D ASKED IF WAS A SAFETY RECALL. I WAS TOLD NO. I THEN HAD THEM TO THE CAR TO SUBARU OF AMERICA IN ORLA…
Read full complaint
MAY OF 2017 I WAS DRIVING NORTH BOUND ON 294. AS I WAS GOING THROUGH THE CURVE THE POWER STEERING LIGHT CAME ON THE CAR WOULDN'T TURN BACK. I STOP AND WAS ABLE TO PULL THE CAR OFF THE ROAD WITH NO INCIDENT. I CALLED SIS IT'S A D ASKED IF WAS A SAFETY RECALL. I WAS TOLD NO. I THEN HAD THEM TO THE CAR TO SUBARU OF AMERICA IN ORLAND PARK IL. WHEN THE CAR WAS FROSTED TOLD I WAS TOLD THE CAR WOULD BE FIX IT WAS COMMON PROBLEM WITH THE POWER STEERING MOTOR. SUBARU OF AMERICA THEN CONTACTED ME SAYING THE CAR WAS INVOLVED IN ACCIDENT SO IT WOULDN'T BE FIXED. ONCE THEY FOUND OUT I WAS BLACK. I FILED A BETTER BUSINESS REPORT SUBARU STILL DENIED THE CLAIM TELLING TO USE MY INSURANCE MY INSUWPULDNT PAY SAID IT DEFECT PART. SUBARU FAILED TO EXAMINE THE UNDERLYING PROBLEM BEFORE DENYING THE CLAIM. SUBARU IMMEDIATELY BLAMED ME BUT NEVER CHECKING THE PROBLEM. ONCE I RECEIVED THE CAR BACK. IT WAS IN WORST CONDITION. THE CAR CANE BACK IN WORST CONDITIONS BUMPER PEELING FENDER SMASHED. I WAS TOLD THAT WAS MY FAULT THE CAR CAME BACK WORST. THAT INTERFERED WITH THE OTHER THINGS IN WARRANTY BEING REPAIRED L WAS DIAGNOSED WITH BIG C. IN 2017 NOW BACK TO OK HEALTH I CAN PROCEED WITH PROCESS. I RENTED CARS FOR A YEAR AND THEN EVENTUALLY BROUGHT ONE. I NEED SUBARU TO REPAIR THE CAR I WANT TO KEEP IT.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2016 Subaru Legacy Problems, Complaints & Recalls | Skip That Year
Illustration