RIGHT REAR CENTERLOCK HUB FAILED/SHEARED OFF RESULTING IN HIGH SPEED EXIT FROM ROAD SURFACE AND 800' SLIDE. WHEEL AND TIRE LEFT VEHICLE AND TRAVELED APPROXIMATELY 1500' CROSSING ACTIVE ROAD. CENTERLOCK NUT WAS FOUND ABOUT 700' FROM VEHICLE. ISSUE SEEMS TO BE FAILURE OF THE CENTERLOCK HUB CAN RESULT IN LOSS OF WHEEL AND VEHIC…
Read full complaint
RIGHT REAR CENTERLOCK HUB FAILED/SHEARED OFF RESULTING IN HIGH SPEED EXIT FROM ROAD SURFACE AND 800' SLIDE. WHEEL AND TIRE LEFT VEHICLE AND TRAVELED APPROXIMATELY 1500' CROSSING ACTIVE ROAD. CENTERLOCK NUT WAS FOUND ABOUT 700' FROM VEHICLE. ISSUE SEEMS TO BE FAILURE OF THE CENTERLOCK HUB CAN RESULT IN LOSS OF WHEEL AND VEHICLE CRASH. BUTTONWILLOW RACEWAY PARK, CA UPON EXITING BUTTONWILLOW TURN 12 (CW DIRECTION), LOUD POP HEARD FROM RIGHT REAR OF CAR (WITNESS DESCRIBE VERY LOUD POP/BANG "LIKE HAND GRENADE GOING OFF"), VEHICLE IMMEDIATELY ROTATED COUNTER CLOCKWISE AND EXITED ROAD SURFACE, SLIDING SIDEWAYS (RIGHT SIDE IN DIRECTION OF SLIDE), RIGHT SIDE DOWN, LEFT SIDE UP (BOTH OCCUPANTS NOTED THEY FELT THE VEHICLE WAS GOING TO ROLL), PARALLEL TO THE ROAD SURFACE. AFTER SLIDING POSSIBLY 600 FEET, CAR HIT INTERSECTING ROAD (ABOUT 6 INCH RISE IN SURFACE) BECOMING AIRBORNE FOR POSSIBLY 20 FEET PASSING OVER THE ROAD AND PIVOTING CLOCKWISE. UPON LANDING, CAR SLID PARALLEL WITH ORIGINAL ROAD SURFACE, ALIGNED WITH ROAD COMING TO REST AFTER ABOUT 800 FEET AFTER THE HUB FAILED. CAR DID NOT ROLL, THE SLIDE SIDEWAYS AND LIKELY THE IMPACT WITH THE CROSS ROAD DID SIGNIFICANT DAMAGE TO THE CAR. DETAILS ON VEHICLE: - WHEEL WAS INSTALLED 2 DAYS PRIOR TO INCIDENT AFTER CHANGING TO NEW DOT TIRES. PORSCHE CENTERLOCK MOUNTING AND TORQUING PROCEDURE WERE FOLLOWED, TORQUING TO 444 FT LB. - TORQUE WRENCH SETTING WAS VERIFIED AFTER INCIDENT AND FOUND TO BE SET PROPERLY TO 444 FT LB. - DATA SHOWS VEHICLE WAS TRAVELING ABOUT 100 MPH, WITH THROTTLE ON AND LOADED WITH 1.1 - 1.2 LATERAL GS (TURNING LEFT, LOADED ON RIGHT SIDE), BRAKE AND STEERING INFORMATION IS NOT AVAILABLE. WHEN HUB FAILED. *TR
Porsche is recalling certain model year 2010 911 GT3 vehicles manufactured May 15, 2009, through February 11, 2010. The rear wheel hubs may be prone to failure under certain driving conditions. Also, the original, suggested maintenance intervals may be insufficient to prevent wheel hub failure.
Consequence & remedy
Consequence: If the rear hub fails, there may be a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will replace the wheel hubs on the rear axle free of charge. The service interval specifications will also be revised and provided to owners as part of Porsche's owner notification letter. The recall began on January 22, 2013. Owners may contact Porsche at 1-800-767-7243.
Additional source detail variants (2)
Wheels:hub
Porsche is recalling certain model year 2010 911 GT3 vehicles manufactured May 15, 2009, through February 11, 2010. The rear wheel hubs may be prone to failure under certain driving conditions. Also, the original, suggested maintenance intervals may be insufficient to prevent wheel hub failure.
Consequence: If the rear hub fails, there may be a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will replace the wheel hubs on the rear axle free of charge. The service interval specifications will also be revised and provided to owners as part of Porsche's owner notification letter. The recall began on January 22, 2013. Owners may contact Porsche at 1-800-767-7243.
Suspension:rear:axle:spindle
Porsche is recalling certain model year 2010 911 GT3 vehicles manufactured May 15, 2009, through February 11, 2010. The rear wheel hubs may be prone to failure under certain driving conditions. Also, the original, suggested maintenance intervals may be insufficient to prevent wheel hub failure.
Consequence: If the rear hub fails, there may be a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will replace the wheel hubs on the rear axle free of charge. The service interval specifications will also be revised and provided to owners as part of Porsche's owner notification letter. The recall began on January 22, 2013. Owners may contact Porsche at 1-800-767-7243.
PORSCHE IS RECALLING CERTAIN MODEL YEAR 2010-2011, 911 TURBO; TURBO S, 911 GT3, GT3 RS AND GT2 RS HIGH PERFORMANCE VEHICLES, MANUFACTURED FROM MAY 18, 2009 THROUGH SEPTEMBER 17, 2010, AND EQUIPPED WITH CENTER LOCKING HUB AND WHEEL ASSEMBLIES. OVER TIME THE HUBS CAN WEAR PREMATURELY.
Consequence & remedy
Consequence: AS THE HUBS WEAR, THE WHEELS COULD LOOSEN, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE CENTRAL LOCKING HUBS AND WHEELS WITH AN IMPROVED DESIGN, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 28, 2011. OWNERS MAY CONTACT PORSCHE AT 1-800-767-7243.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2010 Porsche 911 GT3 Problems, Complaints & Recalls | Skip That Year
Illustration