IllustrationI HAD THE 8 COOLANT FITTINGS, PRONE TO EPOXY FAILURES, SECURED TO HOUSINGS BY WELDING. COST FOR WELDING WAS $275. *TR
2010 Porsche 911 GT3
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all 911 GT3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 3 of 3 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports1 fire reports0 injury reports
Engine complaints
2 reportsCOOLANT LINES / FITTINGS WELDED/ PINNED - MK2 MEZGER ENGINE HAS A FAULTY DESIGN OF COOLANT HOSES/LINES. UPON RESEARCH ONLINE, I AM NOT THE ONLY PERSON AFFECTED BUT ALL TURBO/GT3/RS/GT2 CARS FROM 2004-CURRENT I HAVE ALSO COME ACROSS CARS WITH LESS THAN 10K MILES THAT HAD THIS PROBLEM SO MY PROBLEM IS NOT ISOLATED. THERE HA…
Read full complaint
COOLANT LINES / FITTINGS WELDED/ PINNED - MK2 MEZGER ENGINE HAS A FAULTY DESIGN OF COOLANT HOSES/LINES. UPON RESEARCH ONLINE, I AM NOT THE ONLY PERSON AFFECTED BUT ALL TURBO/GT3/RS/GT2 CARS FROM 2004-CURRENT I HAVE ALSO COME ACROSS CARS WITH LESS THAN 10K MILES THAT HAD THIS PROBLEM SO MY PROBLEM IS NOT ISOLATED. THERE HAS BEEN INCIDENCE ON HIGHWAY WHERE THESE HOSES JUST BURST OR LOSES FITTING AND SPILLS COOLANT CONTENTS ALL OVER THE ROAD. THIS ALSO CAUSE CAR TO SPIN OUT SINCE LOST IN PRESSURE AND TRACTION. VERY DANGEROUS. PORSCHE DEALER WILL ONLY USE DIFFERENT GLUE TO FIT THEM. PROPER WAY IS NOT USE RUBBER HOSE BUT TO USE METAL PIPES AND WELD THEM SO THESE COOLANT LINES DO NOT EVER FALL OUT. THIS COULD HAVE CAUSED CATASTROPHIC INJURY IN PUBLIC ROAD. PORSCHE DENIES ANY FAULTY OR SUB-STANDARD MATERIAL THAT WAS USED IN A CRITICAL COMPONENT OF HIGH PERFORMANCE ENGINE. IN ORDER FOR ME TO FIX THIS, I HAVE TO PAY MY PORSCHE MECHANIC TO REMOVE THE ENGINE, FIND THE COOLANT LINES, REPLACE ALL OF THE HOSES WITH METAL PIPE LINES, WELD THEM, THEN PUT IT BACK IN THE ENGINE BAY. I FEEL THAT I SHOULD HAVE TO PAY FOR THIS OUT OF POCKET FOR SAFETY OF MYSELF OR OTHERS IN PUBLIC ROAD. PORSCHE SUGGESTED THAT THEY WILL USE THE SAME RUBBER HOSES WITH JUST A BETTER ADHESIVE GLUE TO HOLD THEM. THEY WILL FAIL WITHIN TIME. THIS IS A TEMPORARY FIX THEY ARE OFFERING. IT IS FOR SAFETY OF THE MOTORIST. *TR
Official recalls
212V558000 · Suspension:rear:axle:spindle; Wheels:hub
Dec 3, 2012
Porsche is recalling certain model year 2010 911 GT3 vehicles manufactured May 15, 2009, through February 11, 2010. The rear wheel hubs may be prone to failure under certain driving conditions. Also, the original, suggested maintenance intervals may be insufficient to prevent wheel hub failure.
Consequence & remedy
Consequence: If the rear hub fails, there may be a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will replace the wheel hubs on the rear axle free of charge. The service interval specifications will also be revised and provided to owners as part of Porsche's owner notification letter. The recall began on January 22, 2013. Owners may contact Porsche at 1-800-767-7243.
Additional source detail variants (2)
Wheels:hub
Porsche is recalling certain model year 2010 911 GT3 vehicles manufactured May 15, 2009, through February 11, 2010. The rear wheel hubs may be prone to failure under certain driving conditions. Also, the original, suggested maintenance intervals may be insufficient to prevent wheel hub failure.
Consequence: If the rear hub fails, there may be a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will replace the wheel hubs on the rear axle free of charge. The service interval specifications will also be revised and provided to owners as part of Porsche's owner notification letter. The recall began on January 22, 2013. Owners may contact Porsche at 1-800-767-7243.
Suspension:rear:axle:spindle
Porsche is recalling certain model year 2010 911 GT3 vehicles manufactured May 15, 2009, through February 11, 2010. The rear wheel hubs may be prone to failure under certain driving conditions. Also, the original, suggested maintenance intervals may be insufficient to prevent wheel hub failure.
Consequence: If the rear hub fails, there may be a loss of vehicle control, increasing the risk of a crash.
Remedy: Porsche will notify owners, and dealers will replace the wheel hubs on the rear axle free of charge. The service interval specifications will also be revised and provided to owners as part of Porsche's owner notification letter. The recall began on January 22, 2013. Owners may contact Porsche at 1-800-767-7243.
11V285000 · Wheels:lugs/nuts/bolts/studs
Jun 10, 2011
PORSCHE IS RECALLING CERTAIN MODEL YEAR 2010-2011, 911 TURBO; TURBO S, 911 GT3, GT3 RS AND GT2 RS HIGH PERFORMANCE VEHICLES, MANUFACTURED FROM MAY 18, 2009 THROUGH SEPTEMBER 17, 2010, AND EQUIPPED WITH CENTER LOCKING HUB AND WHEEL ASSEMBLIES. OVER TIME THE HUBS CAN WEAR PREMATURELY.
Consequence & remedy
Consequence: AS THE HUBS WEAR, THE WHEELS COULD LOOSEN, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE CENTRAL LOCKING HUBS AND WHEELS WITH AN IMPROVED DESIGN, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 28, 2011. OWNERS MAY CONTACT PORSCHE AT 1-800-767-7243.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.