2012 Mini Cooper

HANDBRAKE HARNESS NOT ROUTED AS DESIGNED. FROM THE PICTURE YOU CAN SEE THE HARNESS NOT INSIDE THE CLIP. THIS MAKES THE HANDBRAKE HARNESS SHORT FROM POINT TO POINT. WHICH WILL LEAD TO MY REAR PASSENGER SIDE BRAKE ALWAYS ON. AND ALSO, IT WILL CAUSE A SERIOUS SAFETY ISSUE IF I WANT TO USE MY HANDBRAKE TO STOP MY VEHICLE. THE FORCE APPLIED ON PASSENGER SIDE IS WAY MORE THAN DRIVE SIDE ( IT WAS INSTALLED CORRECTLY ) . AND IT MAY LEAD MY PASSENGER SIDE HANDBRAKE WIRING HARNESS BROKEN ( BECAUSE OF THE INCORRECT ROUTING ) I FOUND IT OUT WHEN MY BRAKE LIGHT IN ON. MY FRONT BRAKE STILL WORKING FOR ANOTHER 1100 MILES WHILE MY REAR BRAKE SENSOR TELL ME I NEED TO CHANGE MY BRAKE . WE CHANGE THE REAR PASSENGER BRAKE AND FOUND OUT ITS DIFFICULT TO CLIP THE HANDBRAKE WIRING HARNESS TO RIGHT HOLE. THEN WE TRACK THE WIRING DONE. IT'S SHOCKS ME . THE ROUTING IS 100% INCORRECT. YOU CAN SEE THE CORRECT HANDBRAKE HOLE IS EMPTY.

PASSENGER OCCUPANCY SENSOR IS MALFUNCTIONING LEADING TO THE PASSENGER AIRBAG BEING DISABLED WHILE IN MOTION. A PERSON SITTING IN THE PASSENGER SEAT TRIGGERS THE AIRBAG SENSOR WARNING AND DISABLING OF THE AIRBAG. WHILE THE PERSON IS SITTING IN THE PASSENGER SEAT, THE WARNING CAN COME ON AND OFF, AND THE ERROR DOES NOT OCCUR WHILE THE SEAT IS UNOCCUPIED. THE OCCUPANCY SENSOR MAT NEEDS TO BE REPLACED YET IT IS NOT AVAILABLE TO BE SOLD SEPARATELY AND REQUIRES REPLACING OF THE ENTIRE SEAT CUSHION (COST PROHIBITIVE) AND IS NOT COVERED UNDER WARRANTY. THE 2012 MINI COOPER MODEL IS NOT COVERED BY THE MINI RECALL FOR THE SAME EXACT ISSUE WHICH HAS AFFECTED THOUSANDS OF VEHICLES.

WHILE DRIVING FOR ABOUT 30 MINUTES ON THE HIGHWAY, MY MINI COOPER SHUT OFF COMPLETELY, I WAS ABLE TO PULL ONTO THE SHOULDER AND THAT IS WHEN SMOKE STARTED COMING FROM THE ENGINE, WITHIN 6 MINUTES MY WHOLE ENGINE WAS ENGULFED IN FLAMES, CAR TOTALED. INSURENCE INSPECTORS COULDN'T FIGURE OUT A CAUSE. ONE OF THE FIRE FIGHTERS SAID IT LOOKS LIKE IT STARTED NEAR THE WATER PUMP. THERE ARE RECALLS ON OTHER MODELS FOR THIS PROBLEM, BUT NOT MINE. MY MINI HASN'T BEEN WORKED ON SINCE LAST YEAR WHEN I GOT NEW TIRES, I ALSO KEEP UP WITH EVERY OIL CHANGE. *TR

VEHICLE WAS IN MOTION ON A HIGHWAY AND, AFTER GOING OVER SEVERAL POT HOLES, THE ENGINE TEMPERATURE WARNING LIGHT CAME ON. THE ENGINE POWER WAS REDUCED, AND THE ENGINE FAILURE LIGHT ALSO APPEARED. THIS IS WHEN I PULLED OVER INTO THE OFF RAMP, AND THE VEHICLE CAME TO A SPUTTERING STOP. I PLACED THE CAR IN NEUTRAL AND PUSHED IT TO THE DIRT SIDE LANE OF THE OFF RAMP. I OPENED THE HOOD, SMELLED SOMETHING BURNING, AND SAW SMOKE COMING FROM THE ENGINE. I COULD SEE BURNT CIRCUITS, BURNT PLASTIC, AND COOLANT LEAKING ALL OVER THE ENGINE AND EXPOSED WIRING. HAD IT NOT BEEN FOR IMMEDIATELY EXITING ONTO THE OFF RAMP, THE VEHICLE WOULD HAVE STOPPED IN THE MIDDLE OF THE HIGHWAY WITHOUT WARNING. I COULD HAVE ALMOST DIED BECAUSE OF THE FIRE; THIS FAULTY ENGINEERING BY BMW/MINI HAS ALREADY TAKEN THE LIFE OF A DRIVER IN SOUTH KOREA. BMW ISSUED A RECALL OF THE 2012 MINI COOPER S ROADSTER IN SOUTH KOREA, BUT WHEN I HAD THE CAR TOWED TO ONE OF THEIR SERVICE CENTERS, THE TECHNICIANS WERE UNAWARE OF THIS MANUFACTURING DEFECT AND STATED THAT THE REPAIR PARTS ARE UNAVAILABLE. I SEE THAT MY VEHICLE HAS BEEN RECALLED, BUT WHEN I TYPE IN MY VIN, NO RECALL IS ATTACHED TO MY VEHICLE. BMW/MINI IS TAKING NO ACTION; THEY ARE HARMING AND KILLING DRIVERS OF ITS VEHICLES.

VEHICLE WAS IN MOTION ON A HIGHWAY AND, AFTER GOING OVER SEVERAL POT HOLES, THE ENGINE TEMPERATURE WARNING LIGHT CAME ON. THE ENGINE POWER WAS REDUCED, AND THE ENGINE FAILURE LIGHT ALSO APPEARED. THIS IS WHEN I PULLED OVER INTO THE OFF RAMP, AND THE VEHICLE CAME TO A SPUTTERING STOP. I PLACED THE CAR IN NEUTRAL AND PUSHED IT TO THE DIRT SIDE LANE OF THE OFF RAMP. I OPENED THE HOOD, SMELLED SOMETHING BURNING, AND SAW SMOKE COMING FROM THE ENGINE. I COULD SEE BURNT CIRCUITS, BURNT PLASTIC, AND COOLANT LEAKING ALL OVER THE ENGINE AND EXPOSED WIRING. HAD IT NOT BEEN FOR IMMEDIATELY EXITING ONTO THE OFF RAMP, THE VEHICLE WOULD HAVE STOPPED IN THE MIDDLE OF THE HIGHWAY WITHOUT WARNING. I COULD HAVE ALMOST DIED BECAUSE OF THE FIRE; THIS FAULTY ENGINEERING BY BMW/MINI HAS ALREADY TAKEN THE LIFE OF A DRIVER IN SOUTH KOREA. BMW ISSUED A RECALL OF THE 2012 MINI COOPER S ROADSTER, BUT WHEN I HAD THE CAR TOWED TO ONE OF THEIR SERVICE CENTERS, THE TECHNICIANS WERE UNAWARE OF THIS MANUFACTURING DEFECT AND STATED THAT THE REPAIR PARTS ARE UNAVAILABLE. I SEE THAT MY VEHICLE HAS BEEN RECALLED, BUT WHEN I TYPE IN MY VIN, NO RECALL IS ATTACHED TO MY VEHICLE. BMW/MINI IS TAKING NO ACTION; THEY ARE HARMING AND KILLING DRIVERS OF ITS VEHICLES.

VEHICLE WAS IN MOTION ON A HIGHWAY AND AFTER GOING OVER SEVERAL POT HOLES THE ENGINE TEMPERATURE WARNING LIGHT CAME ON. THE ENGINE POWER WAS REDUCED AND AN ENGINE FAILURE LIGHT ALSO APPEARED. THIS IS WHEN I PULLED OVER INTO THE OFF RAMP AND THE VEHICLE CAME TO A SPUTTERING STOP. I PLACED THE CAR IN NEUTRAL AND PUSHED IT TO THE DIRT SIDE LANE OF THE OFF RAMP. I OPENED THE HOOD, SMELLED SOMETHING BURNING, AND SAW SMOKE COMING FROM THE ENGINE. I COULD SEE BURNT CIRCUITS, BURNT PLASTIC, AND COOLANT LEAKING ALL OVER THE ENGINE AND EXPOSED WIRING. HAD IT NOT BEEN FOR IMMEDIATELY EXITING ONTO THE OFF-RAMP, THE VEHICLE WOULD HAVE STOPPED IN THE MIDDLE OF THE HIGHWAY WITHOUT WARNING.

THE PASSENGER SEAT AIR BAG LIGHT CAME ON ONE DAY WHEN STARTING THE CAR. I TOOK IT INTO A MINI SPECIALIST AND THEY SAID IT WAS THE INDICATOR SENSOR IN THE SEAT. OTHER MINI MODELS HAVE HAD THE SAME PROBLEM AND HAVE BEEN RECALLED. HE QUOTED $600-700 TO REPAIR IT. HE COULD NOT GUARANTEE THE AIR BAG WOULD DEPLOY IN AN ACCIDENT. THIS SEEMS LIKE A NO BRAINER.

BRAKE LIGHT FAILED, BULB COULD NOT BE REMOVED FROM INSIDE THE VEHICLE. DEALER SAID THE COMPLETE ASSEMBLY WOULD NEED TO BE REPLACED. UPON REMOVING THE ASSEMBLY, THE FIXTURE WAS REVIEWED TO FIND WHERE EXCESIVE HEAT HAD MELTED THE CONNECTION TO THE BULB (SAME ONES USED IN BMWS THAT MELTED THE WIRING HARNESS BACK IN 2003). I REPAIRD THE THE ASSEMBLY BY SOLDERING THE SOCKETS TO THE BOARD SUCH THAT IT DID NOT DEPEND ON A PIECE OF PLASTIC FOR PRESSURE CONTACT. IT WORKS, BUT WHEN A BULB TRUELY BURNS OUT, THE ASSEMBLY MUST BE REMOVED TO CHANGE THE BULB.