IllustrationMy car shifts from Drive into Park when I'm moving less than 5 miles an hour, so I've been trapped (momentarily) taking turns, in intersections, in traffic.
2015 MERCEDES-BENZ GLK350
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2015 MERCEDES-BENZ GLK350 do not stand out strongly from the model-year median of 114.
About this comparison →How this year compares
Owner complaints by model year
Compare all GLK350 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 26 of 114 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 84 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Fuel/propulsion System. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports2 fire reports4 injury reports
Vehicle Speed Control complaints
5 reportsDRIVING 25 MPH AROUND A CURVE WHEN MY CAR LOST CONTROL, DESPITE MY BEST ATTEMPTS MY CAR WOULD NOT ALLOW ME TO TAKE CONTROL OR TO BREAK. MY CAR WENT FROM 25 MPH TO 60 MPH THROUGH A TWO LANE TRAFFIC STREET, FORCING ME TO SWERVE IN AND OUT OF TRAFFIC MERELY MISSING SIX CARS AND A SEMI TRAILER TRUCK, SPINNING MY CAR AROUND TWICE AN…
Read full complaint
DRIVING 25 MPH AROUND A CURVE WHEN MY CAR LOST CONTROL, DESPITE MY BEST ATTEMPTS MY CAR WOULD NOT ALLOW ME TO TAKE CONTROL OR TO BREAK. MY CAR WENT FROM 25 MPH TO 60 MPH THROUGH A TWO LANE TRAFFIC STREET, FORCING ME TO SWERVE IN AND OUT OF TRAFFIC MERELY MISSING SIX CARS AND A SEMI TRAILER TRUCK, SPINNING MY CAR AROUND TWICE AND FACING THE OPPOSITE DIRECTION OF TRAFFIC.
ON JUNE 16,2017, WHILE I WAS DRIVING ON FREEWAY, I TRIED TO SLOWED DOWN BUT IT TURNED OUT TO ACCELERATE SUDDENLY AT AROUND 85MPH, THE STEERING SYSTEM WAS MESSED UP AND I LOST CONTROL OF MY CAR , THE MORE I TRY TO BRAKE THE FASTER THE CAR CRASHED , SO IT CRASHED TO THE RIGHT SIDE AND ROLLED OVER DOWN TO THE DITCH , I CALLED 91…
Read full complaint
ON JUNE 16,2017, WHILE I WAS DRIVING ON FREEWAY, I TRIED TO SLOWED DOWN BUT IT TURNED OUT TO ACCELERATE SUDDENLY AT AROUND 85MPH, THE STEERING SYSTEM WAS MESSED UP AND I LOST CONTROL OF MY CAR , THE MORE I TRY TO BRAKE THE FASTER THE CAR CRASHED , SO IT CRASHED TO THE RIGHT SIDE AND ROLLED OVER DOWN TO THE DITCH , I CALLED 911 AND UNFORTUNATELY THERE WAS NO SIGNAL, I COULD NOT OPEN THE DOOR NOR WINDOW. THE SMOKE CAME OUT FROM INSIDE AND THE CAR CAUGHT ON FIRE , I COULD HAVE BEEN BURNT TO DEATH ALIVE WITHOUT PEOPLE PASSING BY , THEY USED A BIG ROCK TO BREAK THE WINDOW AND PULLED ME OUT OF THE CAR, TWO MINUTES LATER , THE CAR EXPLODED AND BURNT TO GROUND. THIS IS A HORRIBLE EXPERIENCE , PEOPLE LIKE ME SPENT SO MUCH MONEY ON PURCHASING SUCH AN EXPENSIVE CAR WITH EXPECTATION TO BE SAFER IN DRIVING , BUT WHEN IT COMES TO CAR ACCIDENT , THERE ARE STILL SO MANY FLAWS WHICH COULD HAVE LED TO WRONGFUL DEATH , THIS MAKES ME FEEL FRUSTRATED AND I CALLED MB LONG BEACH AND BEVERLY HILLS , THEY JUST SHOWED INDIFFERENT AND IT'S NONE OF THEIR BUSINESS . I'M NOW VERY DISAPPOINTED AND I HOPE THERE WON'T BE ANY VICTIMS LIKE THIS . I WAS THE EXCEPTION AND I HOPE PEOPLE DRIVING MB GLK350 COULD BE LUCKY ENOUGH . MB OWES ME AN EXPLANATION AND INDEPENDENT INVESTIGATION SHOULD BE CARRIED OUT , MAYBE A RECALL IF NECESSARY FOR THE SAFETY OF CONSUMERS .
MY MB GLK 35 CRASHED AT A HIGH SPEED AROUND 80 MPH,IT BURNT TO GROUND . I WOULD HAVE BEEN BURNT ALIVE WITHOUT PEOPLE USING A BIG ROCK TO BREAK THE WINDOW AND PULLING ME OUT . DUE TO THE STEERING AND ENGINE MALFUNCTION , MY CAR CRASHED AND I COULDN'T OPEN THE DOOR NOR WINDOWS . THIS IS HORRIBLE EXPERIENCE , MERCEDES BENZ NEEDS TO…
Read full complaint
MY MB GLK 35 CRASHED AT A HIGH SPEED AROUND 80 MPH,IT BURNT TO GROUND . I WOULD HAVE BEEN BURNT ALIVE WITHOUT PEOPLE USING A BIG ROCK TO BREAK THE WINDOW AND PULLING ME OUT . DUE TO THE STEERING AND ENGINE MALFUNCTION , MY CAR CRASHED AND I COULDN'T OPEN THE DOOR NOR WINDOWS . THIS IS HORRIBLE EXPERIENCE , MERCEDES BENZ NEEDS TO INVESTIGATE THIS ACCIDENT AND I DON'T WANT MORE VICTIMS LIKE THIS .
WHILE EXITING THE HWY THE CAR SLOW DOWN ON ITS OWN FROM ABOUT 60 TO AROUND 45 WITHOUT BREAKING. INOPERATIVE SEE OWNER'S MANUAL APPEARED ON THE DASHBOARD AND THE CAR STARTED LOOSING POWER. WHEN I TRIED TO ACCELERATE IT DID WOULD NOT SPEED UP PASS 50. AFTER COMING TO A TRAFFIC LIGHT I TRIED TO ACCELERATE AND IT WAS VERY SLOW E…
Read full complaint
WHILE EXITING THE HWY THE CAR SLOW DOWN ON ITS OWN FROM ABOUT 60 TO AROUND 45 WITHOUT BREAKING. INOPERATIVE SEE OWNER'S MANUAL APPEARED ON THE DASHBOARD AND THE CAR STARTED LOOSING POWER. WHEN I TRIED TO ACCELERATE IT DID WOULD NOT SPEED UP PASS 50. AFTER COMING TO A TRAFFIC LIGHT I TRIED TO ACCELERATE AND IT WAS VERY SLOW EVEN WHEN THE PEDAL WAS ALL THE WAY DOWN TO THE FLOOR. LUCKILY THERE WAS NO ONE ON THE ROAD AT THE TIME. I PUMP THE PEDAL SEVERAL TIMES TRYING TO SPEED UP AND IT WOULD NOT GO PASS 55-60 DESPITE PRESSING THE GAS TO THE FLOOR. AFTER I GOT HOME I TURNED THE CAR OFF AND ON THEN DRIVE IT AGAIN, ACCELERATION SEEMED TO COME BACK AND THE LIGHTS WERE NO LONGER ON THE DASHBOARD
Official recalls
419V787000 · Communication
Nov 1, 2019
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V787-4620.pdf
Consequence & remedy
Consequence: An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy: MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
19V010000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2019
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and 2014-2016 E550 Coupe vehicles sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally, MBUSA is recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio, 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2011 C300, 2011-2014 C300 4Matic, C350, C63 AMG, E350 Cabrio, E350 Coupe, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2011-2016 E550 Cabrio, E550 Coupe, 2011-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." MBUSA is also recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2010-2011 C300, 2010-2014 C300 4Matic, C350, C63 AMG, E350 Coupe, 2011-2014 E350 Cabrio, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2016-2017 E550 Cabrio, 2010-2016 E550 Coupe, 2010-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
17V627000 · Air Bags:frontal
Oct 6, 2017
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.
Consequence & remedy
Consequence: If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy: MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
17V252000 · Steering
Apr 12, 2017
Mercedes-Benz USA LLC. (MBUSA) is recalling certain 2013-2014 C250, C300 4MATIC, GLK250 4MATIC BLUETEC and GLK350 vehicles, 2013 C250 Coupe, C350, C350 4MATIC Coupe, C350 Coupe and C63 AMG Coupe vehicles, and 2013-2015 GLK350 4MATIC vehicles. The steering coupling connecting bolt may have been insufficiently tightened, possibly resulting in a loss of steering.
Consequence & remedy
Consequence: A loss of steering can increase the risk of a crash.
Remedy: MBUSA will notify owners, and dealers will inspect the steering coupling connecting bolt, tightening it as necessary, free of charge. The recall began May 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.