← New search

2015 MERCEDES-BENZ GLK350

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2015 MERCEDES-BENZ GLK350 do not stand out strongly from the model-year median of 114.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all GLK350 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

Limited mileage data: 26 of 114 reports include usable mileage. There isn’t enough coverage to show a useful chart.

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 84 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Fuel/propulsion System. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

4 crash reports2 fire reports4 injury reports

Engine complaints

3 reports
Clear category filter
79,614 miles · Nov 24, 2020
EngineVehicle Speed ControlWheels

DRIVING 25 MPH AROUND A CURVE WHEN MY CAR LOST CONTROL, DESPITE MY BEST ATTEMPTS MY CAR WOULD NOT ALLOW ME TO TAKE CONTROL OR TO BREAK. MY CAR WENT FROM 25 MPH TO 60 MPH THROUGH A TWO LANE TRAFFIC STREET, FORCING ME TO SWERVE IN AND OUT OF TRAFFIC MERELY MISSING SIX CARS AND A SEMI TRAILER TRUCK, SPINNING MY CAR AROUND TWICE AN…

Read full complaint

DRIVING 25 MPH AROUND A CURVE WHEN MY CAR LOST CONTROL, DESPITE MY BEST ATTEMPTS MY CAR WOULD NOT ALLOW ME TO TAKE CONTROL OR TO BREAK. MY CAR WENT FROM 25 MPH TO 60 MPH THROUGH A TWO LANE TRAFFIC STREET, FORCING ME TO SWERVE IN AND OUT OF TRAFFIC MERELY MISSING SIX CARS AND A SEMI TRAILER TRUCK, SPINNING MY CAR AROUND TWICE AND FACING THE OPPOSITE DIRECTION OF TRAFFIC.

NHTSA ODI #11376095

16,250 miles · Sep 30, 2015
Engine

DRIVING BACK FROM VACATION LAST SATURDAY, ON THE PENNSYLVANIA TURNPIKE, OUR MOTOR SHUT ITSELF OFF. MY HUSBAND WAS DRIVING, USING CRUISE CONTROL, GOING STRAIGHT, WITH THE "ECON" BUTTON TURNED OFF. LUCKILY TRAFFIC WAS LIGHT AND WE WERE ABLE TO COAST TO A STOP OFF THE RIGHT SIDE OF THE FREEWAY WITHOUT MISHAP. MY HUSBAND TURNED T…

Read full complaint

DRIVING BACK FROM VACATION LAST SATURDAY, ON THE PENNSYLVANIA TURNPIKE, OUR MOTOR SHUT ITSELF OFF. MY HUSBAND WAS DRIVING, USING CRUISE CONTROL, GOING STRAIGHT, WITH THE "ECON" BUTTON TURNED OFF. LUCKILY TRAFFIC WAS LIGHT AND WE WERE ABLE TO COAST TO A STOP OFF THE RIGHT SIDE OF THE FREEWAY WITHOUT MISHAP. MY HUSBAND TURNED THE KEY OFF, WAITED ABOUT A MINUTE, THEN STARTED THE ENGINE AGAIN. THE "CHECK ENGINE" LIGHT CAME ON, BUT OUR MOTOR STAYED ON, AND WE DROVE HOME WITHOUT ANY MORE PROBLEMS. I MADE AN APPOINTMENT WITH OUR M.B. DEALER TO HAVE THE CAR SERVICED ON THIS COMING FRIDAY, OCT. 2ND., EXPLAINING WHAT HAD OCCURRED. THE CHECK ENGINE LIGHT WENT OUT SOMETIME ON MONDAY, SEPT. 28TH. AND HASN'T COME ON AGAIN, BUT IF THE ENGINE DIES AGAIN AT A MORE INOPPORTUNE TIME IT COULD CAUSE SERIOUS, POSSIBLY FATAL, CONSEQUENCES. I AM VERY CONCERNED. BEFORE THIS FAILURE OUR CAR'S MOTOR HAS RUN SMOOTHLY WITH NO PROBLEMS. HOPEFULLY OUR DEALER WILL BE ABLE TO IDENTIFY THE CAUSE WHEN THEY CHECK OUR ONBOARD COMPUTER.

NHTSA ODI #10778870

2,700 miles · Jan 25, 2015
Electronic Stability Control (esc)EngineFuel/propulsion System

MESSAGE DASHBOARD INDICATOR (MDI) READ "INOPERATIVE. SEE OPERATOR'S MANUAL" WITH OTHER MALFUNCTION LIGHTS INCLUDING CHECK ENGINE LIGHT (CEL). TURNED CAR OFF AN ON AND ONLY THE CEL REMAINED. ALSO, THERE WAS A RECURRING TICKING NOISE THAT PRECEDED AFOREMENTIONED ISSUES THAT I ALSO REPORTED. DEALERSHIP REPAIRED LOOSE PIN IN ENGINE …

Read full complaint

MESSAGE DASHBOARD INDICATOR (MDI) READ "INOPERATIVE. SEE OPERATOR'S MANUAL" WITH OTHER MALFUNCTION LIGHTS INCLUDING CHECK ENGINE LIGHT (CEL). TURNED CAR OFF AN ON AND ONLY THE CEL REMAINED. ALSO, THERE WAS A RECURRING TICKING NOISE THAT PRECEDED AFOREMENTIONED ISSUES THAT I ALSO REPORTED. DEALERSHIP REPAIRED LOOSE PIN IN ENGINE ECU (P045100) FOR THE CEL AND REPLACED A HIGH PRESSURE FUEL PUMP FOR THE TICKING NOISE. TICKING NOISE CONTINUED AND VEHICLE RETURNED TO DEALERSHIP WHERE THEY DETERMINED THE TICKING NOISE WAS RELATED TO THE DASH/RADIO/AC CONTROL PANEL/DASH TRIMMING MOVING AGAINST EACH OTHER BUT INDICATED THAT THIS WAS NORMAL (3778 MILES) . THE ISSUE RELATED TO THE MDI AND CEL OCCURRED AGAIN ON 01/25/2015. AS WITH THE INITIAL OCCURRENCE, THE CEL REMAINED ON AFTER RESTARTING THE VEHICLE. THE VEHICLE SEEMED TO STALL WHILE I WAS DRIVING 65 MPH ON A MAJOR HIGHWAY WHEN DRIVING A FEW HOURS LATER. FORTUNATELY, I WAS ABLE TO EXIT THE HIGHWAY. I NOTICED THAT THE CAR DROVE VERY SLUGGISHLY. FOR EXAMPLE, THE CAR WOULD HARDLY ACCELERATE REGARDLESS OF HOW FAR DOWN I PRESSED THE ACCELERATOR AFTER ATTEMPTING TO CONTINUE FROM THE RED LIGHT. I RECALLED THIS HAPPENING WITH THE FIRST OCCURRENCE BUT THEN THOUGHT IT WAS SOMETHING I WAS DOING INCORRECTLY. THE ENGINE LIGHT REMAINED ON AFTER RESTARTING THE VEHICLE AND AS I DROVE APPROXIMATELY 10 MINUTES TO MY FINAL DESTINATION. THE ENGINE LIGHT DID NOT COME ON WHEN I STARTED THE CAR AGAIN AT 10:40 AM (4017 MILES). OUT OF CONCERN, AND ADVICE FROM FAMILY MEMBERS GIVEN WHAT HAPPENED WHEN DRIVING AT A HIGH SPEED, I TOOK THE CAR TO A LOCAL AUTO STORE TO SEE IF THEY COULD DETERMINE ANY FAULT CODES. A CODE OF P2138 WAS RETURNED. *TR

NHTSA ODI #10678793

Official recalls

4

19V787000 · Communication

Nov 1, 2019

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V787-4620.pdf

Consequence & remedy

Consequence: An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

Remedy: MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

19V010000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2019

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and 2014-2016 E550 Coupe vehicles sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally, MBUSA is recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio, 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2011 C300, 2011-2014 C300 4Matic, C350, C63 AMG, E350 Cabrio, E350 Coupe, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2011-2016 E550 Cabrio, E550 Coupe, 2011-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." MBUSA is also recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2010-2011 C300, 2010-2014 C300 4Matic, C350, C63 AMG, E350 Coupe, 2011-2014 E350 Cabrio, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2016-2017 E550 Cabrio, 2010-2016 E550 Coupe, 2010-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.

17V627000 · Air Bags:frontal

Oct 6, 2017

Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.

Consequence & remedy

Consequence: If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.

Remedy: MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.

17V252000 · Steering

Apr 12, 2017

Mercedes-Benz USA LLC. (MBUSA) is recalling certain 2013-2014 C250, C300 4MATIC, GLK250 4MATIC BLUETEC and GLK350 vehicles, 2013 C250 Coupe, C350, C350 4MATIC Coupe, C350 Coupe and C63 AMG Coupe vehicles, and 2013-2015 GLK350 4MATIC vehicles. The steering coupling connecting bolt may have been insufficiently tightened, possibly resulting in a loss of steering.

Consequence & remedy

Consequence: A loss of steering can increase the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will inspect the steering coupling connecting bolt, tightening it as necessary, free of charge. The recall began May 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.