2020 Kenworth T680

Right-hand shift stalk between the shifter and the transmission is causing the vehicle to become disabled while stopped and unable to go from forward to reverse. Also getting SPN 639 pop-up when communication has been lost between the engine control module (ECM) and SAE J1939 data link. The check engine light illuminates, and the ECM immediately logs the fault code. Have to depress brake pedal while stopped & cycle gear selector to get fault to clear to start engine . Message also displayed Transmission Fault Repair Required Find Service Center . Also had new spring clutch replaced in May of 2024. Truck has 525k miles on it .

The clutch Spring on these trucks have been failing heavily. We have a couple more of these trucks and they all have the same issue. the housing for the clutch springs are cracked or damaged at less than 500,000 miles on a heavy duty truck. These clutches are supposed to last over 1MM miles. Its not a coincidence that every truck we have is failing at the same mileage. These clutches are made defective from the manufacturer. Its also a coincidence that the replacement clutches are not the original design and are of a newer design and brand. THIS is RED FLAGS!!!!

My circumstances are EXACTLY as described in a release 12/19/2019 Tech Service Bulletin A002 I experienced the vibration in my steering wheel that caused me to be suspect that there was something wrong in the drive train. Upon further investigation. I noticed that an oil seal was leaking, and when I dug a little deeper, I noticed gears that were broken and shaved down and then stopped at a Kenworth corporate location upon which they told me that I needed to purchase the entire unit to fix it. I then decided that I was going to add some differential oil and drive at a speed of 45 miles an hour, which did not cause any vibration to Chicago, which was roughly 3 hours away from my location in Michigan upon which I would have more resources at my disposal. It is then that I learned of the technical service bulletin relating to my issue. I then took it to CIT trucks which is where I learned that you do not have to buy the complete unit that. The parts are available to be purchased to fix the issue. They did, however say that they would process the claim on behalf of this technical service bulletin. They advised me that the individual that they got a hold of seem to have an attitude about it and sometimes this happens whereas other times they will get a hold of somebody that will make an exception. Apparently they stated my situation is two months out of warranty from when my tractor was placed into service but it’s original owner. I am not in a position due to other issues that I have experience with the truck since purchasing it in June that I can afford this but more importantly, there is a known issue with the same exact identical problem that I experienced. I need help with my situation they need to be held accountable for what has gone wrong because it is not my fault.

When driving, the truck will not go into gear. For example, if I am trying to shift gears in the automatic, it will stay in that gear. When traveling down the highway, it stays in a gear. I have to find a safe place to pull over and put it in neutral, then proceed. I have already changed the right hand stalk once before and it didnt go into reverse, that was the reason for changing it. I get codes saying that it needs to ve changed again and it was just recently put on.

ON SUNDAY, THE 22ND OF MARCH, I WAS TRAVELING SOUTH ON US HWY 45. THE SKY WAS CLEARING AND THE ROAD WAS DRY. I HAD MY CRUISE SET TO 65 MPH. AS I APPROACHED AN OVERPASS, THE DISTANCE SENSOR ON THE FRONT OF THE TRUCK MISTOOK THE SHADOW OF THE OVERPASS AS A STOPPED VEHICLE. WARNING LIGHTS AND BUZZERS WENT OFF AND THE VEHICLE DID A HARD BRAKE. LUCKILY, THERE WERE NO OTHER VEHICLES AROUND ME. I TOOK IT TO OUR SHOP AND THE SYSTEM WAS CLEANED. FOUR DAYS LATER, THE SENSOR MISTOOK AN OVERHEAD INTERSTATE SIGN FOR A STOPPED VEHICLE. AGAIN, THE WARNING LIGHTS AND BUZZERS AND A HARD BRAKE. KENWORTH TECHS WERE SENT OUT TO OUR SHOP TO MAKE REPAIRS. EVERY ONE OF OUR DRIVERS THAT I HAVE SPOKEN TO HAVE EXPERIENCED THE SAME THING MULTIPLE TIMES. THIS IS DANGEROUS. IF SOMEONE HAD BEEN FOLLOWING ME, THEY WOULD HAVE REAR-ENDED MY TRAILER.