NHTSA owner reports · September 18, 2026 snapshot.
Official recalls
8Apr 14, 2020
Daimler Trucks North America LLC (DTNA) is recalling certain 2006-2020 Freightliner Columbia, 2006-2021 Freightliner Business Class M2, 2007-2020 Freightliner Coronado, 2014-2021 Freightliner 122 SD, 2007 Sterling A 9500, 2006 Freightliner Argosy, 2006-2007 Sterling AT9500, 2008-2021 Freightliner Cascadia, 2006-2008 Freightliner Classic, 2006-2011 Freightliner Century Class, 2006-2010 Freightliner FLD, and 2017 Western Star 5700 vehicles. The rear reflective tape may be partially covered by the mudflap hanger bracket, which may reduce the vehicle's visibility to other drivers on the road. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: The vehicle's rearward visibility may be reduced, increasing the risk of a crash.
Remedy: DTNA will notify owners, and dealers will inspect and reposition the reflective tape to ensure that it is completely visible, as necessary, free of charge. The recall began May 29, 2020. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's number for this recall is FL848.
Apr 12, 2016
Daimler Trucks North America LLC (DTNA) is recalling certain model year 2010-2017 Freightliner M2 Business Class, 108SD, 114SD, and Columbia trucks manufactured from January 6, 2010, through February 29, 2016, equipped with certain Bendix rear disk brakes and spring suspensions. The rear disk brake caliper may have been installed incorrectly, thus allowing the caliper to contact the suspension.
Consequence & remedy
Consequence: Caliper contact with the spring suspension may reduce the braking effectiveness, increasing the risk of a crash.
Remedy: DTNA will notify owners, and dealers will correct the orientation of the rear brake calipers, as necessary, free of charge. The recall began on June 8, 2016. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's recall number for this campaign is FL-705.
Oct 1, 2015
Daimler Trucks North America LLC (DTNA) is recalling certain model year 2011-2014 Cascadia, Business Class M2, Coronado, and Columbia Glider vehicles manufactured April 5, 2010, to June 15, 2013. The affected trucks are equipped with Fontaine Ultra LT Fifth Wheel connectors, which, due to cumulative damage to the fifth wheel and its locking mechanism, have a locking mechanism that may fail to operate or to properly engage.
Consequence & remedy
Consequence: If the fifth wheel and locking mechanism are sufficiently damaged, the locking mechanism may fail to operate as intended and the trailer may unexpectedly detach from the tractor, increasing the risk of a crash.
Remedy: DTNA will notify owners, and DTNA authorized service facilities will replace the fifth wheel with an Ultra NT model fifth wheel, free of charge. The recall began on November 20, 2015. Owners may contact DTNA customer service at 1-800-745-8000. DTNA's number for this recall is FL-692.
Dec 16, 2013
Daimler Trucks North America (DTNA) is recalling certain model year 2009-2014 model year Freightliner Business Class M2 and Freightliner Custom Chassis MT45 and MT55 chassis manufactured August 27, 2008, through December 10, 2013 and equipped with Eaton hybrid automated transmissions. The software controlling the affected transmissions may improperly raise the vehicle's engine speed during downshifts without the driver's input.
Consequence & remedy
Consequence: The increase in engine speed may result in unintended acceleration, increasing the risk of a crash.
Remedy: DTNA will notify owners and dealers will update the hybrid transmission software, free of charge. The recall began on February 5, 2014. Owners may contact DTNA at 1-503-745-6910. DTNA's recall number is FL-657.
Aug 16, 2012
Daimler Trucks North America (DTNA) is recalling certain model year 2009-2012 Freightliner, Sterling, and Western Star vehicles manufactured from July 7, 2008, through December 15, 2011, and equipped with perpendicular air tank mounting brackets. The air tank mounting brackets may develop cracks which can lead to the air tank brackets separating from the frame rail. The air tanks may also separate from the vehicle.
Consequence & remedy
Consequence: Air tanks that become separated from a moving vehicle may create a road debris hazard, increasing the risk of a crash.
Remedy: DTNA will notify owners, and dealers will replace the air mounting brackets, free of charge. The recall began on December 24, 2012. Owners may contact Daimler Trucks North America toll free at 1-800-547-0712.
Feb 28, 2012
DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2006-2013 FREIGHTLINER, STERLING, AND WESTERN STAR VEHICLES, EQUIPPED WITH DETROIT DIESEL EPA07 AND EPA10, DD13 AND DD15/16 ENGINES, MANUFACTURED FROM JANUARY 20, 2006, THROUGH FEBRUARY 20, 2012. THE PUMP TO RAIL HIGH PRESSURE FUEL LINE SUPPORT SYSTEM USED ON THESE ENGINES IS SENSITIVE TO ASSEMBLY TORQUE AND MAY BE DAMAGED DURING SERVICE WORK. AS A RESULT OF OTHER REPAIRS, THE LINE SUPPORTS MAY LOOSEN, POTENTIALLY LEADING TO FUEL LINE CRACKING AND A FUEL LEAK.
Consequence & remedy
Consequence: A FUEL LEAK COULD CREATE A ROAD HAZARD, INCREASING THE RISK OF A CRASH. ALSO A FUEL LEAK IN THE PRESENCE OF AN IGNITION SOURCE CAN RESULT IN A FIRE.
Remedy: DTNA WILL NOTIFY OWNERS, AND WHERE NECESSARY, THE HIGH PRESSURE FUEL LINE SUPPORT SYSTEM WILL BE REPLACED BY DTNA AUTHORIZED SERVICE FACILITIES, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 27, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
Dec 27, 2011
DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 FREIGHTLINER BUSINESS CLASS M2 AND WESTERN STAR 4900 EMERGENCY VEHICLES MANUFACTURED FROM JULY 2, 2010, THROUGH DECEMBER 13, 2011, EQUIPPED WITH A DD13 EPA10 DETROIT DIESEL ENGINE. THE ENGINE SHUTDOWN SOFTWARE NORMALLY PROVIDED TO PROTECT THE ENGINE AND VEHICLE MAY NOT HAVE BEEN DISABLED ON ENGINES INTENDED FOR EMERGENCY VEHICLE APPLICATIONS.
Consequence & remedy
Consequence: IF THE VEHICLE OPERATOR RECEIVES AND IGNORES MULTIPLE WARNINGS INDICATING THE NEED FOR OPERATOR INTERVENTION, THE ENGINE MAY SHUT DOWN UNEXPECTEDLY. UNEXPECTED EMERGENCY VEHICLE ENGINE SHUTDOWN UNDER CERTAIN CONDITIONS COULD HAMPER RESCUE OPERATIONS AND PLACE THE PUBLIC AT RISK.
Remedy: DTNA WILL NOTIFY OWNERS, AND DEALERS WILL DISABLE THE ENGINE SHUTDOWN SOFTWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 13, 2012. OWNERS MAY CONTACT DTNA AT 1-800-547-0712.
Sep 15, 2011
DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2011- 2012 BUSINESS CLASS M2 AND CORONADO TRUCKS MANUFACTURED FROM SEPTEMBER 1, 2010, THROUGH DECEMBER 31, 2010, EQUIPPED WITH A CUMMINS ISX OR ISL DIESEL ENGINE. THE V-BAND CLAMP ASSEMBLY, PART NUMBERS Q187684, Q187685, AND Q187686, USED TO CONNECT THE INLET AND OUTLET CONE SECTIONS TO THE DIESEL OXIDATION CATALYST (DOC)/DIESEL PARTICULATE FILTER (DPF) INCLUDE A T-BOLT WHICH CAN FRACTURE AND FAIL WHEN SUBJECTED TO STRESS OR LOAD. A FRACTURE OR FAILURE OF THE T-BOLT MAY CAUSE THE CLAMP TO LOOSEN AND THE INLET OR OUTLET SECTIONS ATTACHED TO THE DOC/DPF HOUSING TO DISCONNECT.
Consequence & remedy
Consequence: IF THE INLET OR OUTLET SECTIONS DISCONNECT, HOT EXHAUST GASES CAN VENT PRIOR TO EXITING THE TAILPIPE, CREATING THE RISK OF COMBUSTION AND A FIRE. IF BOTH CLAMPS FAIL, THERE IS A RISK IN SOME APPLICATIONS THAT THE DOC/DPF HOUSING MAY DETACH COMPLETELY, CREATING A ROAD HAZARD.
Remedy: DAIMLER TRUCKS IS WORKING WITH CUMMINS TO IDENTIFY AND NOTIFY OWNERS OF THE RECALL CAMPAIGN. REPAIRS WILL BE PERFORMED BY AUTHORIZED CUMMINS DEALERS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 10, 2011. OWNERS MAY CONTACT CUMMINS AT 1-812-377-5000 OR DAIMLER TRUCKS AT 1-800-547-0712.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3PE12018 · Air Brake Reservoir Bracket Fracture
Opened Jun 25, 2012 · Closed Sep 20, 2012
Status: closed (inferred from source dates) · Service Brakes, Air:supply:reservoir/tank
The Office of Defects Investigation (ODI) received Early Warning Reporting (EWR) data from the manufacturer that indicated some number of subject vehicles had allegedly experienced a fracture of one or more support brackets resulting in an unsecured air brake reservoir.This could result in a loss of air pressure necessary for proper service brake application and a potential road hazard if the reservoir separates from the vehicle in operation.By letter dated August 15, 2012, Daimler Trucks North America LLC (DTNA) has notified ODI that it has initiated a safety recall (identified by NTHSA Recall No. 12V-405 and DTNA Recall No. FL-631) to address a safety defect in approximately 1,663 model year (MY) 2009 through 2012 Freightliner 114SD, Business Class M2, Cascadia, Coronado, Sterling 9500 and Western Star 4700 trucks manufactured from July 7, 2008 through December 15, 2011, originally equipped with a specific perpendicular oriented air brake reservoir support bracket (P/N 12-22981-000).To date ODI is unaware of any bracket failures that resulted in a complete separation of the reservoir from the vehicle.Affected owners will be notified by DTNA beginning October 15, 2012 and affected vehicles will have the subject air brake reservoir support brackets replaced with a more robust bracket.Repairs will be performed by DTNA authorized service facilities.Copies of DTNA's reimbursement plan for pre-notification remedies will be submitted to ODI as a supplemental report when available.Accordingly, this investigation is closed.
PE11028 · Output Shaft Failure And Separation
Opened Aug 29, 2011 · Closed Nov 22, 2011
Status: closed (inferred from source dates) · Power Train; Power Train:axle Assembly; Power Train:axle Assembly:axle Shaft; Power Train:axle Hubs; Power Train:driveline; Power Train:driveline:differential Unit; Power Train:driveline:driveshaft; Power Train:driveline:universal Joint
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Additional source detail variants (8)
Power Train:axle Assembly:axle Shaft
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train:axle Assembly
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train:axle Hubs
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train:driveline:differential Unit
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train:driveline:driveshaft
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train:driveline
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train:driveline:universal Joint
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
Power Train
On August 29th 2011 the Office of Defects Investigations (ODI) opened this Preliminary Evaluation (PE11-028) on Daimler Trucks North America (DTNA) for output shaft failures located in the forward-rear axle carrier of certain class 8 vehicles equipped with Arvin Meritor RT series output shaft assemblies.At the time of this (PE) opening, ODI was aware of a field campaign and two field reports thought to be related to this alleged safety concern.The DTNA campaign address a risk resulting from an incorrect heat treatment process of the output shaft (SF441AB); which was initially believed to be associated with the two field reports.On October 21st 2011 ODI received DTNA's PE Information Request (IR) letter response which indicated no additional complaints or field reports related to the alleged defect.ODI also learned that the two original field reports noted in the opening resume were U-joint failures and were unrelated to the service campaign. DTNA claimed a total of 96 warranty claims, all related to performing the service campaign but unrelated to any field failures. Upon receiving DTNA's PE-IR letter response ODI learned that even if a fracture were to occur in relation to the alleged defect, it would be located at the base of the splined section of the shaft opposite the output yoke and inside the axle housing.The Output shaft assembly is bolted into the axle housing and will remain secure in the event of a fracture. Based on the fact that there are no consumer complaints, injuries or field reports and the benign consequence of the alleged defect, ODI is closing this investigation.ODI will continue to monitor this field campaign.
PE10007 · Stop Lamps Intermittent
Opened Feb 3, 2010 · Closed May 23, 2010
Status: closed (inferred from source dates) · Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Additional source detail variants (6)
Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Exterior Lighting:brake Lights
This investigation was opened after ODI was contacted by a fleet alleging that in certain situations, such as a light brake peal application during a low speed operation, the brake lamps fail to illuminate on the rear of the bus.ODI confirmed the problem with two fleets.On April 29, 2010, Daimler filed a defect report concerning this issue. The stop lamps may be intermittent during light brake applications.They are still evaluating the remedial program and will furnish this information to ODI when it is available. This safety recallresolves the issue raised by this investigation. Hence, this investigation is closed.
Illustration