IllustrationWIRING HARNESS LOCATION IS TOO CLOSE TO THE MANIFOLD THEREFORE BURNING AND MELTING WIRES, RECALL WORK DONE ON WIRING HARNESS HOWEVER PROBLEM NOT SOLVED.
1995 Ford F700
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all F700 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 0 of 5 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Parking Brake. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
5 reportsSTARTER WILL NOT DISENGAGE, VEHICLE KEEPS RUNNING AFTER SWITCH IS TURNED OFF.
CRUSHED/SHORTED WIRES IN IGNITION WIRING HARNESS CAUSE ENGINE TO STALL.
WIRING HARNESS ROUTED UNDER CAB FLOORBOARDS SEAM, CAUSING SHARP SEAM TO WEAR THROUGH INSULATION, CAUSING FIRE. (FIRST VEHICLE ON 601570) *DH
WIRING ROUTED IN SUCH A MANNER THAT IT IS DIRECTLY AGAINST SHARP EDGE OF CAB FLOOR, WHICH CUTS INTO WIRE. *DSH
Official recalls
497V111000 · Electrical SYSTEM:12V/24V/48V Battery:cables; Electrical System:wiring:front Underhood
Jul 14, 1997
VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS EQUIPPED WITH 7.0L LIQUEFIED PETROLEUM GAS (LPG) ENGINE OR 7.0L EFI (GASOLINE) ENGINE WITH THE OPTIONAL CAB FLOOR PAN REINFORCEMENT. THE ENGINE WIRING HARNESS OR BATTERY CABLE CAN BE PINCHED BETWEEN THE OPTIONAL CAB REINFORCEMENT AND THE FRAME CAUSING AN ABRASION WHICH COULD RESULT IN AN ELECTRICAL SHORT CIRCUIT.
Consequence & remedy
Consequence: A SHORT CIRCUIT CAN CAUSE OVERHEATING AND ARCING.
Remedy: DEALERS WILL MODIFY THE REINFORCEMENT(S) AND, IF NECESSARY, REPOSITION THE ENGINE WIRING HARNESS (INCLUDING INSTALLATION OF THE REVISED ENGINE WIRE HARNESS RETENTION BRACKET) AND BATTERY CABLE.
Additional source detail variants (2)
Electrical System:wiring:front Underhood
VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS EQUIPPED WITH 7.0L LIQUEFIED PETROLEUM GAS (LPG) ENGINE OR 7.0L EFI (GASOLINE) ENGINE WITH THE OPTIONAL CAB FLOOR PAN REINFORCEMENT. THE ENGINE WIRING HARNESS OR BATTERY CABLE CAN BE PINCHED BETWEEN THE OPTIONAL CAB REINFORCEMENT AND THE FRAME CAUSING AN ABRASION WHICH COULD RESULT IN AN ELECTRICAL SHORT CIRCUIT.
Consequence: A SHORT CIRCUIT CAN CAUSE OVERHEATING AND ARCING.
Remedy: DEALERS WILL MODIFY THE REINFORCEMENT(S) AND, IF NECESSARY, REPOSITION THE ENGINE WIRING HARNESS (INCLUDING INSTALLATION OF THE REVISED ENGINE WIRE HARNESS RETENTION BRACKET) AND BATTERY CABLE.
Electrical SYSTEM:12V/24V/48V Battery:cables
VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS EQUIPPED WITH 7.0L LIQUEFIED PETROLEUM GAS (LPG) ENGINE OR 7.0L EFI (GASOLINE) ENGINE WITH THE OPTIONAL CAB FLOOR PAN REINFORCEMENT. THE ENGINE WIRING HARNESS OR BATTERY CABLE CAN BE PINCHED BETWEEN THE OPTIONAL CAB REINFORCEMENT AND THE FRAME CAUSING AN ABRASION WHICH COULD RESULT IN AN ELECTRICAL SHORT CIRCUIT.
Consequence: A SHORT CIRCUIT CAN CAUSE OVERHEATING AND ARCING.
Remedy: DEALERS WILL MODIFY THE REINFORCEMENT(S) AND, IF NECESSARY, REPOSITION THE ENGINE WIRING HARNESS (INCLUDING INSTALLATION OF THE REVISED ENGINE WIRE HARNESS RETENTION BRACKET) AND BATTERY CABLE.
95V143000 · Vehicle Speed Control
Aug 2, 1995
THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES.
Consequence & remedy
Consequence: THIS WEAR CAN RESULT IN THE GOVERNOR JAMMING IN THEDAMAGED SWIVEL AND COULD PREVENT THE GOVERNOR LEVER FROM RETURNING TO THE IDLE POSITION.
Remedy: DEALERS WILL INSTALL A REVISED GOVERNOR LEVER WITH A STAINLESS STEEL SWIVEL. ALSO LETTERS WILL BE SENT TO VEHICLE OWNERS THAT HAVE THE SAME VEHICLES BUT DO NOT HAVE A FORD INSTALLED HAND THROTTLE ADVISING THEM THAT THEY MAY REQUIRE SERVICE IF THEY HAVE HAD AN AFTER MARKET HAND THROTTLE INSTALLED.
95V092000 · Electrical System:wiring
May 9, 1995
A CONNECTOR IN THE WIRING WHERE THE TILT HOOD MOUNTED LAMPS ATTACH TO THE VEHICLE WIRING HARNESS WAS BUILT WITHOUT SEALING PLUGS. MOISTURE, ROAD SALT OR OTHER CONTAMINANTS CAN ENTER THE CONNECTION RESULTING IN CROSSED CIRCUITS, SHORTS OR CORROSION OF THE WIRING OF THE CONNECTOR.
Consequence & remedy
Consequence: THE HEADLAMPS OR OTHER FRONT-END LIGHTING SYSTEMS CAN MALFUNCTION AS A RESULT OF THIS CONDITION INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.
Remedy: DEALERS WILL INSPECT THE CONNECTOR AND INSTALL SEALING PLUGS IN THE OPEN CAVITIES. IF THE INSPECTION REVEALS CORROSION, A NEW CONNECTOR WILL BE INSTALLED.
94V244000 · Steering:linkages:drag:link:connection
Dec 12, 1994
THE DRAG LINK INSTALLED CAN CONTACT THE FRONT AXLE I-BEAM UNDER CERTAIN EXTREME CONDITIONS. THIS DRAG LINK WAS NOT INTENDED TO BE INSTALLED ON "LOW PROFILE" VEHICLES.
Consequence & remedy
Consequence: THIS CAN RESULT IN LOSS OF STEERING CONTROL.
Remedy: DEALERS WILL INSTALL THE CORRECT DRAG LINK ON THE VEHICLES.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
0No exact-year investigations in this snapshot.