NHTSA owner reports · September 18, 2026 snapshot.
Official recalls
12Mar 25, 2015
Ford Motor Company (Ford) is recalling certain model year 2011-2015 Ford F-350, F-450, and F-550 trucks manufactured February 22, 2010, to January 30, 2015, and equipped with ambulance or fire engine preparation packages. The affected vehicles may detect an incorrect Exhaust Gas Temperature Sensor (EGT) fault indicating that the vehicle is too hot, causing the engine management system to shut down the engine and prevent its immediate restart.
Consequence & remedy
Consequence: Engine shut down and a subsequent cool down period may delay medical treatment or assistance to those needing it, increasing their risk of injury.
Remedy: Ford will notify owners, and dealers will update the Powertrain Control Module (PCM) software, free of charge. The recall began on April 22, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S09.
Feb 25, 2015
Farber Specialty Vehicles (Farber) is recalling various specialty vehicles modified by Farber and equipped with model S2005, S2010, S5005, S5010, S5505, and S5510 wheelchair lifts manufactured by Ricon Corporation. The platform side plate of the affected wheelchair lifts may crack.
Consequence & remedy
Consequence: If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. When the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator.
Remedy: Farber will notify owners to take their vehicles to a Ricon dealer or service center who will install supplemental platform support bumpers. Any platform that has already started cracking will be replaced, free of charge. The recall began on March 24, 2015. Owners may contact Farber customer service at 1-800-331-3188, or Ricon customer service at 1-800-322-2884. Farber's number for this recall is 14E-041.
Jul 24, 2014
Godwin Manufacturing Company, Inc. (Godwin) is recalling certain model year 2010 Ford F-450; 2011 Ford F-550; 2012 Ford F-350 and 2013 F-350 Super Duty trucks modified by Godwin and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Godwin will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began October 28, 2014. Owners may contact Godwin customer service at 1-800-892-0181.
Jun 23, 2014
Palfleet Truck Equipment Company, LLC (Palfleet) is recalling certain model year 2009-2013 Ford F-350, F-450, and F-550 super duty vehicles modified by Palfleet and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Palfleet will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began on July 29, 2014. Owners may contact Palfleet customer service at 1- 502-376-2458.
Jun 18, 2014
Dual-Tech, Inc. (Dual-Tech) is recalling certain model year 2009-2014 Ford F-550 Super Duty trucks modified by Dual-Tech, equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Dual-Tech will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began June 20, 2014. Owners may contact Dual-Tech customer service at 1-800-852-0345.
Jun 13, 2014
Iowa Mold Tooling Co., Inc. will notify owners and dealers to inspect the Muncie PTO pressure switch to determine if it is from the range of defective switches and if required, remove the pressure switch assembly and put a plug in the port where the PTO switch had been installed. This switch was never being utilized. This will be done free of charge. The recall is expected to begin in mid-July 2014. Owners may contact Iowa Mold Tooling Co., Inc. at 1-800-247-5958.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Iowa Mold Tooling Co., Inc. will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began on July 28, 2014. Owners may contact Iowa Mold Tooling Co., Inc. at 1-800-247-5958.
Jun 12, 2014
Stahl is recalling certain model year 2009-2014 Ford F-350 Super Duty, F-450 Super Duty, and F-550 Super Duty vehicles modified by Stahl and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Stahl will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. Owners may contact Stahl customer service at 1-800-277-8245, or Muncie at 1-800-367-7867.
Jun 10, 2014
Utility Truck Equipment Company, LLC (Utility Truck) is recalling certain model year 2010-2013 UTLI41A, 2011 UTLN41, and 2012 UTLN46 aerial trucks manufactured December 2010 to September 2013 equipped with certain Muncie Power Products PTO Assemblies installed on 2010-2013 Ford F-350, F-450 and F-550 vehicles. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Utility Truck will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began in June 2014. Owners may contact Utility Truck customer service at 1-254-857-8813.
Additional source detail variants (2)
Equipment
Utility Truck Equipment Company, LLC (Utility Truck) is recalling certain model year 2010-2013 UTLI41A, 2011 UTLN41, and 2012 UTLN46 aerial trucks manufactured December 2010 to September 2013 equipped with certain Muncie Power Products PTO Assemblies installed on 2010-2013 Ford F-350, F-450 and F-550 vehicles. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Utility Truck will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began in June 2014. Owners may contact Utility Truck customer service at 1-254-857-8813.
Engine And Engine Cooling:engine:gasoline
Utility Truck Equipment Company, LLC (Utility Truck) is recalling certain model year 2010-2013 UTLI41A, 2011 UTLN41, and 2012 UTLN46 aerial trucks manufactured December 2010 to September 2013 equipped with certain Muncie Power Products PTO Assemblies installed on 2010-2013 Ford F-350, F-450 and F-550 vehicles. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Utility Truck will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began in June 2014. Owners may contact Utility Truck customer service at 1-254-857-8813.
Jun 10, 2014
Somerset Welding & Steel, doing business as J&J Truck equipment (J&J), is recalling certain model year 2009-2013 Ford F-350, F-450, and F-550 Super Duty chassis with 6.8L gasoline engines modified by J&J to be equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Somerset will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began August 2014. Owner's may contact Somerset customer service at 1-800-777-2671.
Additional source detail variants (2)
Equipment
Somerset Welding & Steel, doing business as J&J Truck equipment (J&J), is recalling certain model year 2009-2013 Ford F-350, F-450, and F-550 Super Duty chassis with 6.8L gasoline engines modified by J&J to be equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Somerset will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began August 2014. Owner's may contact Somerset customer service at 1-800-777-2671.
Engine And Engine Cooling:engine:gasoline
Somerset Welding & Steel, doing business as J&J Truck equipment (J&J), is recalling certain model year 2009-2013 Ford F-350, F-450, and F-550 Super Duty chassis with 6.8L gasoline engines modified by J&J to be equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Somerset will notify owners, and dealers will install a new pressure switch kit that moves the switch away from the exhaust system, free of charge. The recall began August 2014. Owner's may contact Somerset customer service at 1-800-777-2671.
Jun 4, 2014
Tactical Vehicle Outfitters (Tactical) is recalling certain model year 2010-2014 Ford F-350 and F-550 vehicles modified by Tactical and equipped with certain Muncie Power Products PTO Assemblies. In the affected vehicles, oil may leak from the PTO pressure switch onto a thermal blanket covering the exhaust.
Consequence & remedy
Consequence: The leaking oil may soak into the thermal blanket covering the exhaust, which when combined with heat from exhaust, may result in an increased risk of fire.
Remedy: Tactical will notify owners, and dealers will install a new PTO pressure switch, free of charge. The recall began on August 1, 2014. Owners may contact Tactical customer service at 1-405-603-6700.
Feb 24, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2011 FORD F-150, F-250, F-350, F-450, F-550, EDGE, AND LINCOLN MKX TRUCKS MANUFACTURED FROM OCTOBER 25, 2010, THROUGH NOVEMBER 20, 2010. THESE VEHICLES WERE INSPECTED USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) THAT HAD A CUSTOM SOFTWARE ROUTINE TO READ THE SUSPECT BODY CONTROL MODULE (BCM) SERIAL NUMBER. BASED ON THE SERIAL NUMBER THE BCM WAS EITHER NOT AFFECTED OR REPLACED. THE CUSTOM SOFTWARE ROUTINE WAS NOT READING THE CORRECT SET OF CHARACTERS, AND WAS NOT ABLE TO IDENTIFY A BCM THAT REQUIRED REPLACEMENT AFFECTED BCMS MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALER WILL INSPECT THE BODY CONTROL MODULE AND IF NECESSARY REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Dec 29, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 F-150, F-250, F-350, F-450, F-550, EDGE AND LINCOLN MKX VEHICLES. DURING A SIX-DAY PRODUCTION PERIOD, THE SUPPLIER OF THE BODY CONTROL MODULE MANUFACTURED MODULES THAT MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH CAN RESULT IN AN UNATTENDED VEHICLE FIRE.
Remedy: DEALER WILL REPLACE THE BODY CONTROL MODULE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1RQ14005 · Vehicle Commanded Engine Shutdown
Opened Jan 13, 2015 · Closed Mar 15, 2016
Status: closed (inferred from source dates) · Electrical System:software; Engine; Engine And Engine Cooling:engine:diesel; Engine And Engine Cooling:exhaust System; Engine And Engine Cooling:exhaust System:emission Control
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Additional source detail variants (5)
Electrical System:software
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine And Engine Cooling:engine:diesel
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine And Engine Cooling:exhaust System:emission Control
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine And Engine Cooling:exhaust System
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Engine
The Office of Defects Investigation (ODI) opened this RQ to investigate allegations that the scope and remedy of safety recall 13V-535 were inadequate. Recall 13V-535 was limited to a relatively small population of Ambulance Package vehicles and ODI received complaints of pickup trucks and Fire Engine Prep Package vehicles being affected by the same defect. Ford manufactured approximately 555,985 subject vehicles between February 22, 2010 and January 30, 2015 that may be affected by defective EGT sensors and Powertrain Control Module (PCM) software calibration. The subject vehicles are equipped with four (4) EGT sensors to monitor engine operating conditions. An EGT sensor fault may produce false exhaust over-temperature signals. If these signals are produced, the Powertrain Control Module (PCM) implements a Failure Management Effects Mode (FMEM) and the driver receives a Stop Safely Now (SSN) system warning on the instrument cluster message center. The FMEM triggers a 70% reduction in available engine power over a period of no more than 45 seconds, during which it may not be possible to accelerate or maintain vehicle speed. The PCM then commands the engine to shut down when vehicle speed reaches approximately 1 mph. There is no immediate restart capability. Depending on the PCM software calibration, ignition key position and ambient temperature conditions, the engine may not restart until the end of a 10-60 minute cool down period.Ford and its component supplier(s) made numerous changes to the PCM software calibration and the design, material and manufacture of the EGT sensors over the period of subject vehicle production. This continuous product improvement affected vehicle performance regarding the alleged defect. Ford acknowledges the defect condition in the subject vehicles but argues that an unreasonable risk to motor vehicle safety is limited to Ambulance Package and Fire Engine Prep Package vehicles where commanded shutdown could impact emergency response and patient care. Ford also argues that the defect trend is in decline. Ford also initiated a new safety recall (15V-175) to address the 13V-535 remedy concerns in the Ambulance Package vehicles and Fire Engine Prep Package vehicles. The 15V-175 remedy reprograms the PCM with a new software calibration that stops a single EGT sensor fault to cause the vehicle to enter the FMEM shutdown mode.Ford also initiated an EPA emissions recall (14E03) for all subject vehicles that reprograms the PCM with the software calibration employed in safety recall 15V-175. Finally, Ford initiated a Customer Satisfaction Program (15M01) providing extended warranty coverage of 8 years or 80,000 miles for the the EGT sensors on certain MY2011-2012 subject vehicles.Due to the EPA emissions recall, that had a 66.6% completion rate in Ford's December 2015 progress report to the EPA, the defect trend is in decline. ODI is not aware of any crashes, deaths or injuries related to the alleged defect.ODI believes the alleged defect poses a safety risk but notes that the EPA emissions recall is addressing the safety problem.Compelling issuance of a duplicate recall would not represent a wise use of agency resources.Accordingly, this Recall Query is closed.This action is not a finding that no defect exists and NHTSA will take further action if such action is warranted.
Illustration