NHTSA owner reports · September 18, 2026 snapshot.
Suspension complaints
65 reportsClear category filterMileage unknown · May 21, 2024
StructureSuspensionCrash
The rear shock tower has rusted out and broken away from the frame which was conformed at a local body shop. The passenger side went first then the driver side went about a year later. There was no warning that this was happening until it broke while driving which made us lose control of the car. When we took it to a repair shop…
Read full complaint
The rear shock tower has rusted out and broken away from the frame which was conformed at a local body shop. The passenger side went first then the driver side went about a year later. There was no warning that this was happening until it broke while driving which made us lose control of the car. When we took it to a repair shop and said it was 2006 escape they responded what side did the shock tower break on this was before we told them it was a shock tower they said it's always that part on a escape I personally know 2 other people who have had the same problem all different years of escapes.
NHTSA ODI #11589912
Mileage unknown · Mar 23, 2024
StructureSuspensionWheels
Both rear shocks, mounts, wheel wells, entire length of body door panels passenger seats are just absolutely rusted beyond repair. I've gone to a couple different shops and each one said that there is nothing they can do to fix the issue. Now the vehicle when ridden in just bounces horribly wearing out bearing springs and tires …
Read full complaint
Both rear shocks, mounts, wheel wells, entire length of body door panels passenger seats are just absolutely rusted beyond repair. I've gone to a couple different shops and each one said that there is nothing they can do to fix the issue. Now the vehicle when ridden in just bounces horribly wearing out bearing springs and tires are being worn out. There is only 110759 miles on it and bought this for my wife/ kids cause I've had 3 other escapes in the past so since I work on the road this is prefect sized for then not to big or too small. I've had so many issues this last year with repairs parts and now worried about safety issues.
NHTSA ODI #11579065
Mileage unknown · Jun 14, 2023
StructureSuspension
This 2006 Ford Escape Hybrid, and all first and second generation (2001-2012) Escape models, were designed and built with a significant, known defect in the mating area and materials used for the rear floor pan, rear sub-assembly/rails, and rear inner fender liners/upper shock absorber mounts, all made of pressed steel. The desi…
Read full complaint
This 2006 Ford Escape Hybrid, and all first and second generation (2001-2012) Escape models, were designed and built with a significant, known defect in the mating area and materials used for the rear floor pan, rear sub-assembly/rails, and rear inner fender liners/upper shock absorber mounts, all made of pressed steel. The design of the components renders them subject to trapping road debris/salt/contaminants, and the inferior steel used oxidizes quickly, resulting in perforated areas of substantial rust. In our 2006 model, the right rear inner fender liner was completely replaced, and the rear subassembly/rails were welded, in 2013 with new Ford parts. By May, 2018, it had to be repaired and welded again. As of May, 2013, five years almost to the day, it has again rusted and separated. As this hybrid Escape carries a 600 pound battery between the rails in the rear of the vehicle, this is a substantial, dangerous defect affecting potentially millions of cars manufactured over a decade. The current status of the oxidation, corrosion, rot and decay affecting our Ford Escape has rendered it incapable of being repaired per the auto mechanic shop we visited first, followed by the body shop we visited next. Both indicated that the poor design combined with the steel used contributed to the dangerous vehicle it has become.
NHTSA ODI #11527007
Mileage unknown · Mar 27, 2023
Suspension
2006 FORD ESCAPE. CONSUMER WRITES IN REGARD TO RUSTED OUT REAR SHOCK MOUNTS.
NHTSA ODI #11513957
Mileage unknown · Jan 2, 2023
Power TrainService BrakesSuspensionInjury
Well to put it lightly my rear axial the whole rear end is a mess this did not happen from normal were there is not that many miles I am very confident that if I was mot train on how to control a car if it were to go out of control at a high speed this would be a whole different story just thank how many are still on the road th…
Read full complaint
Well to put it lightly my rear axial the whole rear end is a mess this did not happen from normal were there is not that many miles I am very confident that if I was mot train on how to control a car if it were to go out of control at a high speed this would be a whole different story just thank how many are still on the road this year 2006 escape is a ticking time 💣
NHTSA ODI #11499721
Mileage unknown · Dec 30, 2022
Service BrakesSuspensionWheels
About a week after i bought this car and i bought it used but the abs light came on i took it to have it check out and was told the complete suspendtion system front and back was shot and that it all had to be fix i don't have the money for that i am a disabled veteran and i am scraping by as it is
NHTSA ODI #11499472
Mileage unknown · Nov 27, 2022
StructureSuspensionWheels
THE REAR SHOCK MOUNT RUSTS OUT NOT LONG AFTER MANUFACTURE AND WE THE CONSUMER ARE LEFT WITH THE PILE OF POOP. FORD IS HIGHLY AWARE OF THIS PROBLEM, AND AS I TRANSPORT MY CHILDREN DAILY I WONDER IF THIS WILL BE THE DAY WE DIE. UPON THE SHOCK MOUNT RUSTING OUT, HOPE YOURE RELIGIOUS AND GOD IS YOUR CO PILOT BECAUSE AS THAT POINT T…
Read full complaint
THE REAR SHOCK MOUNT RUSTS OUT NOT LONG AFTER MANUFACTURE AND WE THE CONSUMER ARE LEFT WITH THE PILE OF POOP. FORD IS HIGHLY AWARE OF THIS PROBLEM, AND AS I TRANSPORT MY CHILDREN DAILY I WONDER IF THIS WILL BE THE DAY WE DIE. UPON THE SHOCK MOUNT RUSTING OUT, HOPE YOURE RELIGIOUS AND GOD IS YOUR CO PILOT BECAUSE AS THAT POINT THE SPRING IS WHAT YOU'RE LEFT WITH! ITS SO HORSE [XXX] FORD LEAVES THIS TO THE LITTLE GUY (THE CONSUMERS) TO RECTIFY THEIR PROBLEM DUE TO THEIR INFERIOR MANUFACTURING. I WAS GOING OVER THE I280 BRIDGE IN OREGON OHIO WHEN IT DECIDED IT WAS TIME TO FAIL. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11495034
72,000 miles · Nov 3, 2021
StructureSuspension
The contact owns a 2006 Ford Escape. The contact stated that upon the depression of the accelerator pedal, the front passenger’s side subframe collapsed without warning. Due to the failure, the contact had the vehicle towed to an independent mechanic where it was discovered that severe corrosion on the passenger’s side subframe …
Read full complaint
The contact owns a 2006 Ford Escape. The contact stated that upon the depression of the accelerator pedal, the front passenger’s side subframe collapsed without warning. Due to the failure, the contact had the vehicle towed to an independent mechanic where it was discovered that severe corrosion on the passenger’s side subframe had caused the collapse. Neither the dealer nor the manufacturer had been notified of the failure. The vehicle was not repaired and remained in the possession of the independent mechanic. The failure mileage was approximately 72,000.
NHTSA ODI #11439162
81,500 miles · Sep 25, 2019
Suspension
RIGHT REAR SHOCK MOUNT BROKE LOOSE AND STARTED TO ENTER THE PASSENGER COMPARTMENT.
NHTSA ODI #11257967
220,000 miles · Sep 2, 2018
StructureSuspension
REAR WHEEL WELLS WHERE THE SHOCK MOUNTS IS RUSTED THROUGH CAUSING RIDE AND CONTROL ISSUES. I NOTICED CLUNKING WHILE DRIVING CAUSED BY THE RUST AND LACK OF SHOCK STABILITY. I TALKED TO OTHER OWNERS AND FOUND THIS IS A COMMON ISSUE. BEING THAT MY VEHICLE IS NOT RUSTY AND IS CARED FOR REGULARLY THIS IS BAD AND I AM NO LONGER GOI…
Read full complaint
REAR WHEEL WELLS WHERE THE SHOCK MOUNTS IS RUSTED THROUGH CAUSING RIDE AND CONTROL ISSUES. I NOTICED CLUNKING WHILE DRIVING CAUSED BY THE RUST AND LACK OF SHOCK STABILITY. I TALKED TO OTHER OWNERS AND FOUND THIS IS A COMMON ISSUE. BEING THAT MY VEHICLE IS NOT RUSTY AND IS CARED FOR REGULARLY THIS IS BAD AND I AM NO LONGER GOING TO INVEST MY MONEY INTO IT. THIS IS A SAFETY CONCERN AND I FEEL WITH AS COMMON AS THE ISSUE SEEMS IT SHOULD BE TAKEN CARE OF BY FORD AS THE SHOCK BEING LOOSE COMING INTO THE INTERIOR IS ANOTHER SAFETY CONCERN, AND THE WEAR AND TEAR FROM THE TIRE RIDE CAUSES PREMATURE TIRE WEAR NOT TO MENTION WEAR AND SNAPPING THE BREAK LINE CAUSING THE BRAKES TO FAIL.
NHTSA ODI #11124014
Official recalls
3Sep 29, 2015
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence & remedy
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Additional source detail variants (2)
Power Train:automatic Transmission:lever And Linkage:floor Shift
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Power Train:automatic Transmission:gear Position Indication (prndl)
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Sep 3, 2014
Ford Motor Company (Ford) is recalling certain model year 2005-2008 Ford Escape hybrid electric vehicles manufactured October 13, 2003, to June 20, 2008, and 2006-2008 Mercury Mariner hybrid electric vehicles manufactured June 10, 2005, to June 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.
Consequence & remedy
Consequence: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the original Motor Electronics Coolant (MEC) Pump with an improved brushless pump, free of charge. The recall is expected to begin on October 27, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S19.
Nov 9, 2005
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Consequence & remedy
Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
Illustration