IllustrationBreak booster with leak noted requiring replacement. Turbo boost needing replacement. After turbo boost replacement, began having a shudder during acceleration between 40-48 mph. Now needing torque converter replaced.
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
What owners actually said
2,444 reportsThe brake pedal goes all the way to the floor without stopping the car. It makes a hissing sound. I have almost had three collisions because of it. The Ford service center told me it's three months outside of the manufacture date range for a warrantied service of the brake booster on select Ford Edge models manufactured at the…
Read full complaint
The brake pedal goes all the way to the floor without stopping the car. It makes a hissing sound. I have almost had three collisions because of it. The Ford service center told me it's three months outside of the manufacture date range for a warrantied service of the brake booster on select Ford Edge models manufactured at their Oakridge plant between May 3, 2010 and March 28, 2013. (13N02) My car was manufactured at that plant on June 24, 2013. The warranty extends replacement of the booster pump on cars for 10 additional years up to 150,000 miles. My car's warranty start date is April 21, 2014 and it has less than 100,000 miles. That means it is with in the warranty parameters, except for the date of manufacture. I have opened a case with Ford customer service, but they are telling me that the repair of the brake booster cannot be covered under their warranty extension.
My brake booster failed while driving and lost control. Recall had been issued for for 2013 edge for this problem based on VIN. Mine was not included yet it failed in my low mileage garaged car. Nearly impossible to contact Ford for resolution. If the failure happened on my car it should be covered under Terms of Recall.
The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, the brake pedal was soft and required an abnormal amount of effort to bring the vehicle to a complete stop. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the ABS hydraulic cont…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, the brake pedal was soft and required an abnormal amount of effort to bring the vehicle to a complete stop. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the ABS hydraulic control unit. The contact was informed that the ABS hydraulic control unit needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 88,000.
On at least two occasions, I’ve experienced my brake pedal going all the way to the floor when trying to stop. I’ve had my brakes inspected by two different dealers and both have confirmed that the brakes are in good condition with no repair needs. The brake pedal will slowly continue to the floorboard and then I have to almos…
Read full complaint
On at least two occasions, I’ve experienced my brake pedal going all the way to the floor when trying to stop. I’ve had my brakes inspected by two different dealers and both have confirmed that the brakes are in good condition with no repair needs. The brake pedal will slowly continue to the floorboard and then I have to almost pump them to resume the stopping mechanism. Thankfully, it’s only happened twice and neither incident caused an accident or injury. After reviewing these noted incidents, I see that I’m not the only Edge driver who has experienced this issue that needs review by Ford.
The contact owns a 2013 Ford Edge. The contact stated that on several occasions while driving at various speeds, the brake pedal was depressed to the floor to bring the vehicle to a complete stop. The vehicle was taken to a dealer where it was diagnosed that the brake master cylinder needed to be replaced. The vehicle was repair…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that on several occasions while driving at various speeds, the brake pedal was depressed to the floor to bring the vehicle to a complete stop. The vehicle was taken to a dealer where it was diagnosed that the brake master cylinder needed to be replaced. The vehicle was repaired but the failure persisted. The vehicle was then taken to the same dealer where it was diagnosed that the brake booster needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 141,439.
After filling up the vehicle to the "first click" at the gas station and driving home, noticed strong fuel odor in garage. Next trip noticed a puddle of fuel under the fuel tank and dripping fuel from vehicle. Issue goes away after driving about 75 miles. Next fill up, purposely kept fuel level no higher than about 3/4 tank …
Read full complaint
After filling up the vehicle to the "first click" at the gas station and driving home, noticed strong fuel odor in garage. Next trip noticed a puddle of fuel under the fuel tank and dripping fuel from vehicle. Issue goes away after driving about 75 miles. Next fill up, purposely kept fuel level no higher than about 3/4 tank do not currently have the issue. Am not filling the vehicle to full any longer. No check engine light indicated, even after driving over 300 miles.
The contact owns a 2013 Ford Edge. The contact stated while driving at various speeds, the vehicle suddenly lost motive power and failed to accelerate or move forward. After turning off and restarting the vehicle, the vehicle operated normally. The contact stated that during the failure, the message "Power Train Malfunction" was…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving at various speeds, the vehicle suddenly lost motive power and failed to accelerate or move forward. After turning off and restarting the vehicle, the vehicle operated normally. The contact stated that during the failure, the message "Power Train Malfunction" was displayed. The vehicle was taken to the local mechanic who was unable to determine the cause of the failure. The local dealer was notified of the failure. The manufacturer was not notified of the failure. The failure mileage was 150,000.
I purchased my Ford from a used car lot and only 3 months later without any alerts my brake pedal goes to the floor. It makes a hissing sound like air being released. My brakes and fluid are fine? Why are their recalls on my same year vehicle, but not mine. I understand replacing brake booster, master cylinder will NOT help.…
Read full complaint
I purchased my Ford from a used car lot and only 3 months later without any alerts my brake pedal goes to the floor. It makes a hissing sound like air being released. My brakes and fluid are fine? Why are their recalls on my same year vehicle, but not mine. I understand replacing brake booster, master cylinder will NOT help. Now I am broke from purchasing my Ford, I can't afford to dump more money into a vehicle that can't be fixed. You need to recall the entire car! Now my dash lights go crazy, even ABS once? This car is a freaking lemon and someone is going to get hurt. Then Ford will responsible for their manufactory error?
2013 Ford Edge. My dad's Ford Edge started having brake issues with the pedal going to the floor and the car not stopping. We replaced the master cylinder, and ABS Control Module with dealer parts and the issue continued. We then replaced the brake booster. Same issues are still there. We've even hooked up our $4,000 scanner to …
Read full complaint
2013 Ford Edge. My dad's Ford Edge started having brake issues with the pedal going to the floor and the car not stopping. We replaced the master cylinder, and ABS Control Module with dealer parts and the issue continued. We then replaced the brake booster. Same issues are still there. We've even hooked up our $4,000 scanner to do the brake bleeding process. The brakes have been bleed well over 20 times now. We've spent over a mouth trying to fix this issue. My husband is a ASC Certified Master Tech and has been working on cars for well over 25 years. We're at a loss with this issue. Ford needs to do a recall, there are numerous reports on line of this issue happening to other Ford edge owners. It is Unsafe to have these vehicles on the road when the brakes are not working properly.
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.