NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
168 reportsClear category filterMileage unknown · Jun 27, 2026
EngineFuel/propulsion SystemPower Train
I am filing a consumer complaint against Ford Motor Company regarding a known, severe safety defect in my 2013 Ford Edge 3.5L AWD. The internal water pump has failed, leaking green coolant onto the ground and threatening catastrophic engine failure. Ford designed this vehicle with an internal water pump that dumps coolant into t…
Read full complaint
I am filing a consumer complaint against Ford Motor Company regarding a known, severe safety defect in my 2013 Ford Edge 3.5L AWD. The internal water pump has failed, leaking green coolant onto the ground and threatening catastrophic engine failure. Ford designed this vehicle with an internal water pump that dumps coolant into the engine oil when it fails, hiding the defect from consumers until the powertrain is destroyed. Furthermore, the All-Wheel Drive Power Transfer Unit (PTU) is overheating due to a design that labels the fluid 'lifetime' and prevents standard servicing. I purchased this vehicle for $14,400 and have invested $4,000 in maintenance, and I am seeking state consumer protection advocacy regarding Ford's deceptive engineering practices."
NHTSA ODI #11746866
Mileage unknown · Mar 6, 2026
EngineExterior LightingFuel/propulsion System
I have several different things going on. First of all my rear turn signals do not work, nor do my rear hazard lights. I've taken it to a mechanic who has extensively looked at this and has determined that it's the body control modular and is suggested replacement. I have been waiting for several months for this part to come in …
Read full complaint
I have several different things going on. First of all my rear turn signals do not work, nor do my rear hazard lights. I've taken it to a mechanic who has extensively looked at this and has determined that it's the body control modular and is suggested replacement. I have been waiting for several months for this part to come in but he keeps telling me it's on back order. Also, my radiator fan/assembly went bad and had to be replaced. Upon the mechanic installing the new fan assembly, I had numerous fuses blown and that is when my blinker and hazard light issue started. This is a major safety concern as signaling the direction that you're turning is very important to other drivers. Additionally, it is against the law not to use signals. I'm constantly in fear that someone is going to rear in me because of my inability to signal when switching lanes and or turning. Additionally, my back up camera stopped working shows a black screen with a notice to contact the dealer. Another issue I have is that my door ajar light is illuminated all the time. I often feel unsafe and fear that the door may just come open at any time, I am unable to lock my doors with the internal lock , which means my doors are left unlocked while I'm in the vehicle. Also, the interior lights stay on for awhile when car turned off, thus putting more strain on the battery, which I've just replaced. Plus, the dome light will not go off until you accelerated to about 20 mph, however, when putting the car in reverse there's no way to get the lights to turn off in this causes visibility issues at night. That in conjunction with my backup camera not working makes it a very dangerous situation when going in reverse. I also detect the odor of gasoline which lingers in my vehicle for some time after getting fuel. I'm scared that there's a leak and if so the potential of a fire is very concerning. And I've noticed that my gas mileage is not really good and I'm not sure if that's related.
NHTSA ODI #11722586
Mileage unknown · Dec 8, 2025
EngineFuel/propulsion SystemService Brakes
I purchased this vehicle used in August 2025 from the estate of a friend's relative. The records show it was meticulously maintained and no recall notices have been unaddressed. The prior owner used it infrequently and it still has just under 90k miles. There were no major engine issues when my local repair shop (over 12 years a…
Read full complaint
I purchased this vehicle used in August 2025 from the estate of a friend's relative. The records show it was meticulously maintained and no recall notices have been unaddressed. The prior owner used it infrequently and it still has just under 90k miles. There were no major engine issues when my local repair shop (over 12 years and 3 vehicles) inspected all systems, and the vehicle passed for PA state inspection and emissions. However, driving more, I noticed that the brakes would intermittently become "mushy" or "hard" and overall less responsive. I needed to use a lot of force to fully stop over a longer distance. There was also a hissing noise while braking and sometimes the cabin air fan would blast on suddenly. Then, while stopped at a red light and applying the brakes, the engine shut off and check engine light came on. My mechanic detected O2 sensor codes P2195/P2197 indicating "stuck lean." But nothing about the brake booster, and so we cleaned it up a bit and tried to get more of an understanding of the issue. Now I know that the compromised engine vacuum from the booster air leak is impacting the fuel/air balance. Extremely unsafe. This has now happened MANY times while I try to get a good diagnosis and help. It's scary, and makes city driving very challenging. On multiple occasions I feared I would hit other vehicles or would have to "creep" at a light to alleviate the airflow issues from braking. If I have to be at a light for more than a moment, I will put the car in park and foot off the brake. I'd rather risk being honked at or hit, than have the engine dying on me in traffic. When I was able to get to a dealership, I was informed that it was the brake booster. The first thing I found when looking up that part for the 2013 Ford Edge was the recall. The dealership says my VIN was not covered, but it seems more than coincidence that this is the exact problem, now confirmed by the dealership. The part is faulty, and should be replaced by OEM.
NHTSA ODI #11703726
Mileage unknown · Sep 20, 2025
EngineSteering
Since the day I bought my 2013 Edge I have had nothing but problems ranging from Backup Camera always has a distorted image, appears upside down or it will just be blank. For the last year I have had my car looked at, changed everything that could possibly be changed to now my car can be going down the road running 55-60 MPH and…
Read full complaint
Since the day I bought my 2013 Edge I have had nothing but problems ranging from Backup Camera always has a distorted image, appears upside down or it will just be blank. For the last year I have had my car looked at, changed everything that could possibly be changed to now my car can be going down the road running 55-60 MPH and the car will just shut down and flash random warnings on the dash but the scariest & most unsafe part is how the steering wheel locks up or I lose power steering making it hard to move or coast off the road to safety. At this point I don't know what else to do. Questions below are asking for dates but unfortunately there are so many dates that my car does this as it happens almost daily so I will put date for the last day I drove it. Right now it has been sitting at a mechanic's place for the last 3.5 weeks.
NHTSA ODI #11688651
Mileage unknown · Sep 5, 2025
Engine
Water pump failure coolant leaking out of it Was driving at 10mph in parking garage when temperature gauge went to hot on cluster instrument everyone was ok had have had vehicle for about a month before breakdown private dealer did say there were no issues car has not been checked by a certified dealership.
NHTSA ODI #11685279
164,301 miles · Apr 24, 2025
EngineService Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated that while driving 50 MPH, the brake pedal was depressed, and there was an abnormal grinding sound coming from the vehicle, and the vehicle failed to respond. The brake failure and general warning lights were illuminated. The contact stated that the brakes eventually responde…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving 50 MPH, the brake pedal was depressed, and there was an abnormal grinding sound coming from the vehicle, and the vehicle failed to respond. The brake failure and general warning lights were illuminated. The contact stated that the brakes eventually responded. The vehicle was then taken to an independent mechanic, who diagnosed the vehicle; however, the independent mechanic refused to repair the vehicle. The independent mechanic informed the contact the failure should be covered under recall. The independent mechanic stated that he would be liable if the brakes failed again, and the contact was involved in a crash. The vehicle was then taken to a dealer, where it was diagnosed with brake booster failure. The vehicle received repair for a bent push rod, motor craft, motor, brake fluid, and the upper intake was replaced. After the repair, the failure recurred two more times, and the vehicle was repaired two more times. The vehicle was pending further repairs. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline. The failure mileage was approximately 164,301.
NHTSA ODI #11656519
114,000 miles · Sep 4, 2024
EngineEngine And Engine Cooling
The contact owns a 2013 Ford Edge. The contact stated that after arriving at her destination, the check engine warning light illuminated. The contact stated upon further inspection, she noticed a leak coming from the engine compartment. The vehicle was taken to a local independent mechanic who advised the contact to take the veh…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that after arriving at her destination, the check engine warning light illuminated. The contact stated upon further inspection, she noticed a leak coming from the engine compartment. The vehicle was taken to a local independent mechanic who advised the contact to take the vehicle to a local dealer for assistance. The vehicle was taken to a local dealer where it was diagnosed and determined that the water pump had failed, and that the front of the engine and the timing belt needed to be removed to reach the parts needed to be replaced. Additionally, the bearing behind the water pump needed to be replaced. The vehicle was not repaired due to the costs. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 114,000.
NHTSA ODI #11612584
135,000 miles · Aug 14, 2024
Engine
The contact owns a 2013 Ford Edge. The contact stated while driving at an undisclosed speed, the vehicle shuddered abnormally. No warning light was illuminated. The vehicle was taken to an independent mechanic, who determined that there was coolant intrusion into the cylinders, and that the engine needed to be replaced. The manu…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving at an undisclosed speed, the vehicle shuddered abnormally. No warning light was illuminated. The vehicle was taken to an independent mechanic, who determined that there was coolant intrusion into the cylinders, and that the engine needed to be replaced. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 135,000.
NHTSA ODI #11608486
Mileage unknown · Jun 20, 2024
EngineService Brakes
Backfiring and brakes don’t work.
NHTSA ODI #11595408
180,000 miles · Jun 11, 2024
EngineService Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated while driving and approaching a stop light, the brake pedal was depressed but the vehicle was slow to respond. The contact applied additional pressure to the brake pedal to stop the vehicle. The check engine warning light was illuminated. The vehicle was taken to an independe…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving and approaching a stop light, the brake pedal was depressed but the vehicle was slow to respond. The contact applied additional pressure to the brake pedal to stop the vehicle. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic and the contact was informed that there was a slice in the vacuum pump and that the brake booster needed to be replaced. The vehicle was taken to the local dealer, where it was diagnosed that the brake booster needed to be replaced. The vehicle was not repaired. The contact stated that the failure was related to TSB: 13N02. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 180,000.
NHTSA ODI #11593617
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration