IllustrationThe entire underneath and some panels of the vehicle are completely rusted to the point that the vehicle cannot be safely driven. The vehicle has never been in an ocean front town. Has been in Frankfurt, Germany and Atchison, Kansas.
2001 Dodge Durango
Owner reports · Recalls · Investigations
More warning signs than most Durango years
Owner complaints for the 2001 Dodge Durango are substantially higher than the model-year median of 231.
About this comparison →How this year compares
Owner complaints by model year
Compare all Durango years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
340–25K
14025–50K
9950–75K
5875–100K
51100–150K
33150K+
415 reports with mileage · 250 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Suspension. Review the 265 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 106 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 91 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
60 crash reports20 fire reports36 injury reports
Unknown Or Other complaints
13 reportsAS I AM DRIVING MY BLINKERS AND RADIO STOPPED WORKING RANDOMLY . CAUSING SAFETY ISSUES WHILE ON THE ROAD . THIS HAPPENS WHILE IN MOTION AND ON THE ROAD
DUE TO MY CURRENT LOCATION, THERE IS NO DEALERSHIP IN THE MIDDLE EAST THAT CAN PERFORM THE REQUIRED MAINTENANCE TO COMPLETE THE RECALL. ONCE I AM LOCATED BACK IN CONUS, I'LL BE ABLE TO GET THE VEHICLE TO THE MANAFACTURER TO HAVE THEM COMPLETE THE RECALL.
PRIOR TO THE HUB FREEZING UP THE SUV WAS MAKING A SQUEAKY NOISE IN THE FRONT END THIS LATER TURNED INTO A CLUNKING NOISE AND THE CAR WOULD SWAY WHEN EVER THERE WERE LANE CHANGES ESPECIALLY NOTICEABLE AT HWY SPEEDS 55 TO 65 MPH AND DRIVING OVER THE LANE MARKER CAPS ON THE FREEWAY. THIS THEN DEVELOPED INTO A METAL TO METAL GRINDIN…
Read full complaint
PRIOR TO THE HUB FREEZING UP THE SUV WAS MAKING A SQUEAKY NOISE IN THE FRONT END THIS LATER TURNED INTO A CLUNKING NOISE AND THE CAR WOULD SWAY WHEN EVER THERE WERE LANE CHANGES ESPECIALLY NOTICEABLE AT HWY SPEEDS 55 TO 65 MPH AND DRIVING OVER THE LANE MARKER CAPS ON THE FREEWAY. THIS THEN DEVELOPED INTO A METAL TO METAL GRINDING NOISE FROM THE FRONT END PRIOR TO THE WHEEL ASSEMBLY RIGHT FRONT PASSENGER SIDE SEPARATING INVERTING UNDERSIDE CAR CHASSIS. *TR
I BOUGHT IT IN MARCH 2008 WITH APPROX 75,000 MILES. AFTER A COUPLE MONTHS IT STARTED TO GET LOUD AND THE AIR WOULDN'T BE AS HOT WHEN NOT IN MOTION. EVERY TIME YOU START IT UP OR ACCELERATE IT SOUNDS LIKE LOUD EXHAUST. I TOOK IT IN TO BE READ ON COMPUTER AND SAID IT WAS MY CLUTCH FAN. I HAVE NOW PURCHASED THREE IN THE PAST TWO MO…
Read full complaint
I BOUGHT IT IN MARCH 2008 WITH APPROX 75,000 MILES. AFTER A COUPLE MONTHS IT STARTED TO GET LOUD AND THE AIR WOULDN'T BE AS HOT WHEN NOT IN MOTION. EVERY TIME YOU START IT UP OR ACCELERATE IT SOUNDS LIKE LOUD EXHAUST. I TOOK IT IN TO BE READ ON COMPUTER AND SAID IT WAS MY CLUTCH FAN. I HAVE NOW PURCHASED THREE IN THE PAST TWO MONTHS AND THE PROBLEM WILL NOT GO AWAY. I WAS TOLD TODAY TO TRY BUYING ONE THAT GOES IN A DIFFERENT DIRECTION BUT NO DIFFERENCE. PROBLEM STILL EXISTS AND COMPUTER STILL READS NO OTHER PROBLEM. *TR
CLOCK SPRING FAILURE-SAME SCEANARIO AS CURRENT NHTSA INVESTIGATION INVOLVING DAIMLER CHRYSLER MINI-VANS. FAILURE RESULTED IN A NON-WARRANTY COVERED EXPENSE OF $219.42 IN PARTS AND LABOR TO REPLACE CLOCK SPRING.*AK
I HEARD ABOUT UPPER CONTROL ARM FAILURE. I HAD MINE CHECKED MY MECHANIC STATED RIGHT SIDE UPPER SHOWED SIGNS OF WEAR & SHOULD BE REPLACED. WAITING TO SEE IF RECALL IS FORTHCOMING. NOTICED POWER STEERING WAS HARD TO TURN ALSO A RATTLE IN THE STEERING WHEEL IF SHOOK SIDE TO SIDE FASTLY (CAUSE WORN STEERING COLUMN AND BOX). LIGHT…
Read full complaint
I HEARD ABOUT UPPER CONTROL ARM FAILURE. I HAD MINE CHECKED MY MECHANIC STATED RIGHT SIDE UPPER SHOWED SIGNS OF WEAR & SHOULD BE REPLACED. WAITING TO SEE IF RECALL IS FORTHCOMING. NOTICED POWER STEERING WAS HARD TO TURN ALSO A RATTLE IN THE STEERING WHEEL IF SHOOK SIDE TO SIDE FASTLY (CAUSE WORN STEERING COLUMN AND BOX). LIGHT SELECTOR SWITCH BURNED OUT. HAD TO REPLACE THE SWITCH MODULE.
DURANGO ORGINAL STARTED STALLING AND THEN CHECK ENGINE LIGHT CAME ON AND STAYED ON STEADY. WENT TO DEALER AN WAS SUGGESTED PCM WAS BAD NO PARTS AVAILABLE (POWER CONTROL MODULE). PARTS ORDERED. NEW PARTS INSTALLED SAME PROBLEM WHEN LEAVING DEALERSHIP. ON CLOSER INSPECTION TECHNICAN FOUND REAR HEAT INLINE PUMP HAD FAILED INTERNALL…
Read full complaint
DURANGO ORGINAL STARTED STALLING AND THEN CHECK ENGINE LIGHT CAME ON AND STAYED ON STEADY. WENT TO DEALER AN WAS SUGGESTED PCM WAS BAD NO PARTS AVAILABLE (POWER CONTROL MODULE). PARTS ORDERED. NEW PARTS INSTALLED SAME PROBLEM WHEN LEAVING DEALERSHIP. ON CLOSER INSPECTION TECHNICAN FOUND REAR HEAT INLINE PUMP HAD FAILED INTERNALLY AND HAD PUMPED ANTIFREEZE THROUGH WIRING HARNESS WHICH INTURN WRECKED CRUISE CONTROL, PCM, HEATING AND COOLING CONTROLS. ANTIFREEZE IS CORRSIVE TO COPPER WIRING AND WE DO NOT KNOW HOW FAR THE ANTIFREEZE TRAVELED IN THE DIFFERENT WIRING HARNESS MODULES. DODGE HAS OFFERED TO REPLACE ORIGINAL FAILED INLINE REAR HEAT PUMP BUT WILL NOT PAY LABOR $216.00 DISTRICT MANAGER HAS OFFERED TO GIVE 12 MONTH OR 12,000 MILE WARRANTY BUT WILL NOT GIVE A LONGER WARRANTY ON ELECTRICALL HARNESS EVEN THOUGH HE HAS DETERMINED THIS WILL FIX PROBLEM. BUT NOT REMOVED THE CORROSIVE FROM THE ELECTRICAL HARNESS. TECH WORKING PROBLEM HAS SEE THE SAME PROBLEM BEFORE AT SAME DEALERSHIP ON DURANGO'S
2001 DODGE DURANGO, HAD ROUTINE VISIT TO FIRESTONE TIRE TO GET NEW TIRES FOR THE VEHICLE. THE MECHANIC ADVISED US THAT THE VEHICLE NEEDED BOTH UPPER FRONT BALL JOINTS, UPPER CONTROL ARM REMOVE AND REPLACE, CONTROL UPPER ONE SIDE ALSO LOWER CONTROL ARM REMOVE AND REPLACE BALL JOINT, LOWER, BOTH. HE ADVISED THAT ON SUCH A NEW VE…
Read full complaint
2001 DODGE DURANGO, HAD ROUTINE VISIT TO FIRESTONE TIRE TO GET NEW TIRES FOR THE VEHICLE. THE MECHANIC ADVISED US THAT THE VEHICLE NEEDED BOTH UPPER FRONT BALL JOINTS, UPPER CONTROL ARM REMOVE AND REPLACE, CONTROL UPPER ONE SIDE ALSO LOWER CONTROL ARM REMOVE AND REPLACE BALL JOINT, LOWER, BOTH. HE ADVISED THAT ON SUCH A NEW VEHICLE THIS IS A VERY UNCOMMON OCCURENCE. HE SAID HE WAS UNABLE TO GET THE PARTS TO REPAIR, IF HE COULD HE GAVE ESTIMATE TO US $968.78 VEHICLE HAS NOT HAD AN ACCIDENT SINCE ITS DIAGNOSIS. *AK
GEAR SHIFT MOVES INTO GEAR WITHOUT DEPRESSING THE BRAKE PEDAL. GEAR SHIFT LEVER STICKS OUT PAST STEERING WHEEL IN FRONT OF AC AND RADIO CONTROLS AND IS EASLY KNOCKED INTO GEAR.
Official recalls
507V555000 · Power Train:automatic Transmission:lever And Linkage:column Shift
Dec 4, 2007
ON CERTAIN VAN AND PICKUP TRUCKS EQUIPPED WITH AUTOMATIC TRANSMISSIONS, THE IGNITION/PARK SHIFT INTERLOCK SYSTEM MAY BECOME INOPERATIVE. THIS CAN ALLOW THE SHIFTER TO BE MOVED OUT OF THE "PARK" POSITION WITH THE IGNITION KEY REMOVED (OR IN THE "LOCK" POSITION). THIS CAN ALSO ALLOW THE IGNITION KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE "PARK" POSITION.
Consequence & remedy
Consequence: EITHER OF THESE CONDITIONS COULD ALLOW THE VEHICLE TO ROLL AWAY CAUSING A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPLACE THE GEARSHIFT BLOCKER AND BRACKET ASSEMBLY FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JANUARY 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
06V339000 · Electrical System
Sep 7, 2006
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH FRONT BENCH SEATS ONLY, IF FLUID IS SPILLED FROM THE FLOOR MOUNTED CUP HOLDER, AN UNUSED CONSOLE POWER OUTLET CONNECTOR LOCATED UNDER THE SEAT MAY BECOME CONTAMINATED.
Consequence & remedy
Consequence: THIS MAY ALLOW DEVELOPMENT OF A HIGH RESISTIVE SHORT CIRCUIT IN THE CONNECTOR, WHICH COULD EVENTUALLY LEAD TO A FIRE.
Remedy: DEALERS WILL INSPECT THE CONSOLE WIRING CONNECTOR FOR CORROSION, CLEAN AS REQUIRED, AND INSTALL A CAP TO PREVENT ADDITIONAL FLUID FROM CONTAMINATING THE CONNECTOR FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 30, 2006. OWNERS MAY CONTACT DAIMLER CHRYSLER AT 1-800-853-1403.
04V596000 · Suspension:front:control Arm:upper Ball Joint
Dec 21, 2004
ON CERTAIN SPORT UTILITY VEHICLES AND PICKUP TRUCKS EQUIPPED WITH FOUR-WHEEL DRIVE (4X4), IF MOISTURE LEAKS INTO THE FRONT SUSPENSION UPPER BALL JOINT, EVACUATION OF THE LUBRICANT AND CORROSION OF THE JOINT MAY CAUSE THE JOINT TO WEAR OVER AN EXTENDED PERIOD OF TIME. THIS COULD CAUSE A CLUNKING NOISE IN THE FRONT SUSPENSION, WHICH MAY NOT ALWAYS BE HEARD BY THE VEHICLE OCCUPANTS.
Consequence & remedy
Consequence: EXCESSIVE WEAR IN THE UPPER BALL JOINT MAY ALLOW IT TO SEPARATE, WHICH COULD RESULT IN LOSS OF CONTROL OF THE VEHICLE.
Remedy: DEALERS WILL REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS. THIS SAFETY IMPROVEMENT CAMPAIGN BEGAN ON DECEMBER 21, 2004. OWNERS CAN CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
01V077000 · Power Train:automatic Transmission:lever And Linkage:column Shift
Mar 7, 2001
VEHICLE DESCRIPTION: LIGHT DUTY TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH 4-WHEEL DRIVE. THE ELECTRIC SHIFT TRANSFER CASE MAY NOT FULLY ENGAGE INTO GEAR WHEN THE OPERATOR MOVES THE TRANSFER CASE SELECTOR SWITCH.
Consequence & remedy
Consequence: THIS COULD CAUSE THE TRANSFER CASE TO END UP IN THE NEUTRAL POSITION UNEXPECTEDLY AND ALLOW THE VEHICLE TO ROLL AWAY IF THE PARKING BRAKE IS NOT APPLIED.
Remedy: DEALERS WILL REPROGRAM THE TRANSFER CASE CONTROL MODULE. OWNER NOTIFICATION BEGAN APRIL 9, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
00V366000 · Child Seat
Nov 9, 2000
VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES, PICKUP TRUCKS AND SPORT UTILITY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." SOME OF THE OWNER'S MANUALS FOR THESE VEHICLES ARE MISSING INSTRUCTIONS THAT PROVIDE A STEP-BY-STEP PROCEDURE, INCLUDING DIAGRAMS, FOR PROPERLY ATTACHING A CHILD RESTRAINT SYSTEM'S TETHER STRAP TO THE TETHER ANCHORAGE.
Consequence & remedy
Consequence: IN THE EVENT OF A CRASH, THE CHILD SEAT MAY NOT BE PROPERLY ATTACHED INCREASING THE RISK OF INJURY TO THE CHILD.
Remedy: OWNERS WILL BE PROVIDED WITH AN ADDENDUM TO THE OWNER'S MANUALS.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA06011 · Vehicle UNDER-SEAT Fire
Opened Jun 19, 2006 · Closed Sep 22, 2006
Status: closed (inferred from source dates) · Electrical System; Electrical System:wiring
DAIMLERCHRYLSER CORPORATION (DCC) WILL RECALL 35,103 MY 2001-2003 DODGE DURANGO VEHICLES EQUIPPED WITH FRONT BENCH SEATS (RECALL # 06V339, SEE DEFECT REPORT FOR DETAILS).THE SUBJECT VEHICLES ARE EQUIPPED WITH EITHER FRONT BUCKET SEATS OR A 40-20-40 SPLIT FRONT BENCH SEAT.VEHICLES EQUIPPED WITH FRONT BENCH SEAT CONTAIN AN UNCAPPED, UNUSED CONNECTOR LOCATED UNDER THE FRONT EDGE OF THE SEAT.THE CONNECTOR PROVIDES POWER TO THE CENTER CONSOLE POWER OUTLET FOR VEHICLES WITH BUCKET SEATS, BUT IT IS UNUSED IN VEHICLES EQUIPPED WITH BENCH SEATS.THE CONNECTOR IS LOCATED REARWARD OF THE CUP HOLDER ON THE TUNNEL FOR VEHICLES EQUIPPED WITH THE BENCH SEAT.THIS CONNECTOR CONTAINS A FUSED B+ CIRCUIT WIRE (THAT IS CONTINUOUSLY POWERED WITH THE KEY OFF) AND A GROUND WIRE. DCC DETERMINED THAT IF LIQUID IS SPILLED FROM THE CUP HOLDER ONTO THE TUNNEL, THE UNCAPPED CONNECTOR MAY BECOME CONTAMINATED.THIS CONTAMINATION MAY ALLOW DEVELOPMENT OF A HIGH RESISTANCE SHORT CIRCUIT IN THE CONNECTOR, CAUSING LOCALIZED HEATING, WHICH COULD EVENTUALLY LEAD TO A FIRE.DCC WILL INSPECT THE UNCAPPED CONNECTOR FOR CORROSION, CLEAN AS REQUIRED, AND INSTALL A CAP TO PREVENT LIQUID CONTAMINATION.ALL OF THE REPORTED UNDER-SEAT FIRES WERE ON SUBJECT VEHICLES WITH A 40-20-40 BENCH SEAT.THIS INVESTIGATION IS CLOSED.
Additional source detail variants (2)
Electrical System
DAIMLERCHRYLSER CORPORATION (DCC) WILL RECALL 35,103 MY 2001-2003 DODGE DURANGO VEHICLES EQUIPPED WITH FRONT BENCH SEATS (RECALL # 06V339, SEE DEFECT REPORT FOR DETAILS).THE SUBJECT VEHICLES ARE EQUIPPED WITH EITHER FRONT BUCKET SEATS OR A 40-20-40 SPLIT FRONT BENCH SEAT.VEHICLES EQUIPPED WITH FRONT BENCH SEAT CONTAIN AN UNCAPPED, UNUSED CONNECTOR LOCATED UNDER THE FRONT EDGE OF THE SEAT.THE CONNECTOR PROVIDES POWER TO THE CENTER CONSOLE POWER OUTLET FOR VEHICLES WITH BUCKET SEATS, BUT IT IS UNUSED IN VEHICLES EQUIPPED WITH BENCH SEATS.THE CONNECTOR IS LOCATED REARWARD OF THE CUP HOLDER ON THE TUNNEL FOR VEHICLES EQUIPPED WITH THE BENCH SEAT.THIS CONNECTOR CONTAINS A FUSED B+ CIRCUIT WIRE (THAT IS CONTINUOUSLY POWERED WITH THE KEY OFF) AND A GROUND WIRE. DCC DETERMINED THAT IF LIQUID IS SPILLED FROM THE CUP HOLDER ONTO THE TUNNEL, THE UNCAPPED CONNECTOR MAY BECOME CONTAMINATED.THIS CONTAMINATION MAY ALLOW DEVELOPMENT OF A HIGH RESISTANCE SHORT CIRCUIT IN THE CONNECTOR, CAUSING LOCALIZED HEATING, WHICH COULD EVENTUALLY LEAD TO A FIRE.DCC WILL INSPECT THE UNCAPPED CONNECTOR FOR CORROSION, CLEAN AS REQUIRED, AND INSTALL A CAP TO PREVENT LIQUID CONTAMINATION.ALL OF THE REPORTED UNDER-SEAT FIRES WERE ON SUBJECT VEHICLES WITH A 40-20-40 BENCH SEAT.THIS INVESTIGATION IS CLOSED.
Electrical System:wiring
DAIMLERCHRYLSER CORPORATION (DCC) WILL RECALL 35,103 MY 2001-2003 DODGE DURANGO VEHICLES EQUIPPED WITH FRONT BENCH SEATS (RECALL # 06V339, SEE DEFECT REPORT FOR DETAILS).THE SUBJECT VEHICLES ARE EQUIPPED WITH EITHER FRONT BUCKET SEATS OR A 40-20-40 SPLIT FRONT BENCH SEAT.VEHICLES EQUIPPED WITH FRONT BENCH SEAT CONTAIN AN UNCAPPED, UNUSED CONNECTOR LOCATED UNDER THE FRONT EDGE OF THE SEAT.THE CONNECTOR PROVIDES POWER TO THE CENTER CONSOLE POWER OUTLET FOR VEHICLES WITH BUCKET SEATS, BUT IT IS UNUSED IN VEHICLES EQUIPPED WITH BENCH SEATS.THE CONNECTOR IS LOCATED REARWARD OF THE CUP HOLDER ON THE TUNNEL FOR VEHICLES EQUIPPED WITH THE BENCH SEAT.THIS CONNECTOR CONTAINS A FUSED B+ CIRCUIT WIRE (THAT IS CONTINUOUSLY POWERED WITH THE KEY OFF) AND A GROUND WIRE. DCC DETERMINED THAT IF LIQUID IS SPILLED FROM THE CUP HOLDER ONTO THE TUNNEL, THE UNCAPPED CONNECTOR MAY BECOME CONTAMINATED.THIS CONTAMINATION MAY ALLOW DEVELOPMENT OF A HIGH RESISTANCE SHORT CIRCUIT IN THE CONNECTOR, CAUSING LOCALIZED HEATING, WHICH COULD EVENTUALLY LEAD TO A FIRE.DCC WILL INSPECT THE UNCAPPED CONNECTOR FOR CORROSION, CLEAN AS REQUIRED, AND INSTALL A CAP TO PREVENT LIQUID CONTAMINATION.ALL OF THE REPORTED UNDER-SEAT FIRES WERE ON SUBJECT VEHICLES WITH A 40-20-40 BENCH SEAT.THIS INVESTIGATION IS CLOSED.
PE06008 · Fire Under The Driver's Seat
Opened Feb 2, 2006 · Closed Jun 19, 2006
Status: closed (inferred from source dates) · Electrical System:wiring:interior/under Dash; Seats
ODI IS AWARE OF 10 REPORTS ALLEGING THAT A FIRE ORIGINATES UNDERNEATH THE DRIVER'S SEAT.SIX OF THEFIRES OCCURRED WHILE THE VEHICLE WAS PARKED WITH THE IGNITION SWITCH TURNED OFF (KEY NOT IN THE IGNITION).THE SUBJECT VEHICLES ARE EQUIPPED WITH MANUAL SEATS. THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS, (EA06-011), TO ALLOW FURTHER INVESTIGATION OF THE ISSUE.
Additional source detail variants (2)
Electrical System:wiring:interior/under Dash
ODI IS AWARE OF 10 REPORTS ALLEGING THAT A FIRE ORIGINATES UNDERNEATH THE DRIVER'S SEAT.SIX OF THEFIRES OCCURRED WHILE THE VEHICLE WAS PARKED WITH THE IGNITION SWITCH TURNED OFF (KEY NOT IN THE IGNITION).THE SUBJECT VEHICLES ARE EQUIPPED WITH MANUAL SEATS. THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS, (EA06-011), TO ALLOW FURTHER INVESTIGATION OF THE ISSUE.
Seats
ODI IS AWARE OF 10 REPORTS ALLEGING THAT A FIRE ORIGINATES UNDERNEATH THE DRIVER'S SEAT.SIX OF THEFIRES OCCURRED WHILE THE VEHICLE WAS PARKED WITH THE IGNITION SWITCH TURNED OFF (KEY NOT IN THE IGNITION).THE SUBJECT VEHICLES ARE EQUIPPED WITH MANUAL SEATS. THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS, (EA06-011), TO ALLOW FURTHER INVESTIGATION OF THE ISSUE.
EA03023 · Upper Ball Joint Separation
Opened Nov 19, 2003 · Closed Feb 11, 2005
Status: closed (inferred from source dates) · Suspension; Suspension:front; Suspension:front:control Arm; Suspension:front:control Arm:upper Arm; Suspension:front:control Arm:upper Ball Joint
DAIMLERCHRYSLER CORPORATION (DCC) IS RECALLING THE TARGET POPULATION OF APPROXIMATELY 600,000 MY 2000 THROUGH 2003 DURANGO AND DAKOTA VEHICLES WITH FOUR-WHEEL DRIVE TO REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS WITH REDESIGNED PARTS THAT DO NOT HAVE THE JOINT INTEGRITY CONCERNS AND HAVE SUBSTANTIALLY IMPROVED JOINT RETENTION CAPACITY (NHTSA RECALL NO. 04V-596).THOUGH DCC DOES NOT ADMIT TO A SAFETY-DEFECT IN THE SUBJECT COMPONENTS, ODI BELIEVES THAT THE FACTS IN THIS INVESTIGATION SHOW OTHERWISE.BECAUSE OF THE LOW RATES OF SEPARATION INCIDENTS IN THE REMAINING SUBJECT VEHICLES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED IN THOSE POPULATIONS AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS IN THOSE VEHICLES.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.
Additional source detail variants (5)
Suspension
DAIMLERCHRYSLER CORPORATION (DCC) IS RECALLING THE TARGET POPULATION OF APPROXIMATELY 600,000 MY 2000 THROUGH 2003 DURANGO AND DAKOTA VEHICLES WITH FOUR-WHEEL DRIVE TO REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS WITH REDESIGNED PARTS THAT DO NOT HAVE THE JOINT INTEGRITY CONCERNS AND HAVE SUBSTANTIALLY IMPROVED JOINT RETENTION CAPACITY (NHTSA RECALL NO. 04V-596).THOUGH DCC DOES NOT ADMIT TO A SAFETY-DEFECT IN THE SUBJECT COMPONENTS, ODI BELIEVES THAT THE FACTS IN THIS INVESTIGATION SHOW OTHERWISE.BECAUSE OF THE LOW RATES OF SEPARATION INCIDENTS IN THE REMAINING SUBJECT VEHICLES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED IN THOSE POPULATIONS AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS IN THOSE VEHICLES.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.
Suspension:front
DAIMLERCHRYSLER CORPORATION (DCC) IS RECALLING THE TARGET POPULATION OF APPROXIMATELY 600,000 MY 2000 THROUGH 2003 DURANGO AND DAKOTA VEHICLES WITH FOUR-WHEEL DRIVE TO REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS WITH REDESIGNED PARTS THAT DO NOT HAVE THE JOINT INTEGRITY CONCERNS AND HAVE SUBSTANTIALLY IMPROVED JOINT RETENTION CAPACITY (NHTSA RECALL NO. 04V-596).THOUGH DCC DOES NOT ADMIT TO A SAFETY-DEFECT IN THE SUBJECT COMPONENTS, ODI BELIEVES THAT THE FACTS IN THIS INVESTIGATION SHOW OTHERWISE.BECAUSE OF THE LOW RATES OF SEPARATION INCIDENTS IN THE REMAINING SUBJECT VEHICLES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED IN THOSE POPULATIONS AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS IN THOSE VEHICLES.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.
Suspension:front:control Arm
DAIMLERCHRYSLER CORPORATION (DCC) IS RECALLING THE TARGET POPULATION OF APPROXIMATELY 600,000 MY 2000 THROUGH 2003 DURANGO AND DAKOTA VEHICLES WITH FOUR-WHEEL DRIVE TO REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS WITH REDESIGNED PARTS THAT DO NOT HAVE THE JOINT INTEGRITY CONCERNS AND HAVE SUBSTANTIALLY IMPROVED JOINT RETENTION CAPACITY (NHTSA RECALL NO. 04V-596).THOUGH DCC DOES NOT ADMIT TO A SAFETY-DEFECT IN THE SUBJECT COMPONENTS, ODI BELIEVES THAT THE FACTS IN THIS INVESTIGATION SHOW OTHERWISE.BECAUSE OF THE LOW RATES OF SEPARATION INCIDENTS IN THE REMAINING SUBJECT VEHICLES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED IN THOSE POPULATIONS AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS IN THOSE VEHICLES.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.
Suspension:front:control Arm:upper Arm
DAIMLERCHRYSLER CORPORATION (DCC) IS RECALLING THE TARGET POPULATION OF APPROXIMATELY 600,000 MY 2000 THROUGH 2003 DURANGO AND DAKOTA VEHICLES WITH FOUR-WHEEL DRIVE TO REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS WITH REDESIGNED PARTS THAT DO NOT HAVE THE JOINT INTEGRITY CONCERNS AND HAVE SUBSTANTIALLY IMPROVED JOINT RETENTION CAPACITY (NHTSA RECALL NO. 04V-596).THOUGH DCC DOES NOT ADMIT TO A SAFETY-DEFECT IN THE SUBJECT COMPONENTS, ODI BELIEVES THAT THE FACTS IN THIS INVESTIGATION SHOW OTHERWISE.BECAUSE OF THE LOW RATES OF SEPARATION INCIDENTS IN THE REMAINING SUBJECT VEHICLES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED IN THOSE POPULATIONS AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS IN THOSE VEHICLES.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.
Suspension:front:control Arm:upper Ball Joint
DAIMLERCHRYSLER CORPORATION (DCC) IS RECALLING THE TARGET POPULATION OF APPROXIMATELY 600,000 MY 2000 THROUGH 2003 DURANGO AND DAKOTA VEHICLES WITH FOUR-WHEEL DRIVE TO REPLACE THE FRONT SUSPENSION UPPER BALL JOINTS WITH REDESIGNED PARTS THAT DO NOT HAVE THE JOINT INTEGRITY CONCERNS AND HAVE SUBSTANTIALLY IMPROVED JOINT RETENTION CAPACITY (NHTSA RECALL NO. 04V-596).THOUGH DCC DOES NOT ADMIT TO A SAFETY-DEFECT IN THE SUBJECT COMPONENTS, ODI BELIEVES THAT THE FACTS IN THIS INVESTIGATION SHOW OTHERWISE.BECAUSE OF THE LOW RATES OF SEPARATION INCIDENTS IN THE REMAINING SUBJECT VEHICLES, A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED IN THOSE POPULATIONS AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS IN THOSE VEHICLES.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.
PE03032 · Front Susp. Upper Ball Joint Failure
Opened Jul 16, 2003 · Closed Nov 19, 2003
Status: closed (inferred from source dates) · Suspension:front; Suspension:front:control Arm; Suspension:front:control Arm:upper Arm; Suspension:front:control Arm:upper Ball Joint
IN JULY 2003, ODI OPENED PE03-032 BASED ON 4 CONSUMER COMPLAINTS ALLEGING SEPARATION OF AN UPPER BALL JOINT.COMPLAINTS ALLEGED AN UNEXPECTED COLLAPSE IN THE FRONT END AND IN SOME OCCASIONS THE BALL JOINT SEPARATION IS ALLEGED TO HAVE RESULTED IN THE WHEEL, BRAKE ROTOR, AND STEERING KNUCKLE SEPARATING FROM THE VEHICLE.SINCE OPENING THE PE, ODI HAS RECEIVED 23 ADDITIONAL COMPLAINTS RELATED TO BALL JOINT SEPARATION. DAIMLERCHRYSLER HAS IDENTIFIED A WEAROUT CONCERN IN THE SUBJECT BALL JOINTS THAT IS BELIEVED TO OCCUR AFTER WATER INTRUSION EVACUATES THE JOINT LUBRICANT.DAIMLERCHRYSLER DOES NOT BELIEVE THE CONDITION POSES AN UNREASONABLE RISK TO SAFETY BECAUSE THE SUSPENSION DESIGN IN THE SUBJECT VEHICLES SIGNIFICANTLY REDUCES THE LIKELIHOOD OF JOINT SEPARATION.OVER 99 PERCENT OF THE FAILURES ARE RELATED TO WORN BALL JOINTS (E.G., NOISE COMPLAINTS).DAIMLERCHRYSLER REVISED THE REPAIR PROCEDURE IN AUGUST 2003 TO ALLOW THE UPPER BALL JOINTS TO BE SERVICED SEPARATELY FROM THE UPPER CONTROL ARM AND REDUCE REPAIR COSTS. DAIMLERCHRYSLER CHANGED THE SUPPLIER OF THE SUBJECT BALL JOINTS FROM TRW TO NEW CASTLE MACHINING & FORGE FOR MY 2000 VEHICLES.MY 2000 DURANGO VEHICLES ACCOUNT FOR 25 OF THE 37 SEPARATION COMPLAINTS.THE UPPER BALL JOINT WAS REDESIGNED IN MY 2003.THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER ASSESS THE ALLEGED DEFECT IN MY 2000-02 DURANGO VEHICLES.
Additional source detail variants (4)
Suspension:front
IN JULY 2003, ODI OPENED PE03-032 BASED ON 4 CONSUMER COMPLAINTS ALLEGING SEPARATION OF AN UPPER BALL JOINT.COMPLAINTS ALLEGED AN UNEXPECTED COLLAPSE IN THE FRONT END AND IN SOME OCCASIONS THE BALL JOINT SEPARATION IS ALLEGED TO HAVE RESULTED IN THE WHEEL, BRAKE ROTOR, AND STEERING KNUCKLE SEPARATING FROM THE VEHICLE.SINCE OPENING THE PE, ODI HAS RECEIVED 23 ADDITIONAL COMPLAINTS RELATED TO BALL JOINT SEPARATION. DAIMLERCHRYSLER HAS IDENTIFIED A WEAROUT CONCERN IN THE SUBJECT BALL JOINTS THAT IS BELIEVED TO OCCUR AFTER WATER INTRUSION EVACUATES THE JOINT LUBRICANT.DAIMLERCHRYSLER DOES NOT BELIEVE THE CONDITION POSES AN UNREASONABLE RISK TO SAFETY BECAUSE THE SUSPENSION DESIGN IN THE SUBJECT VEHICLES SIGNIFICANTLY REDUCES THE LIKELIHOOD OF JOINT SEPARATION.OVER 99 PERCENT OF THE FAILURES ARE RELATED TO WORN BALL JOINTS (E.G., NOISE COMPLAINTS).DAIMLERCHRYSLER REVISED THE REPAIR PROCEDURE IN AUGUST 2003 TO ALLOW THE UPPER BALL JOINTS TO BE SERVICED SEPARATELY FROM THE UPPER CONTROL ARM AND REDUCE REPAIR COSTS. DAIMLERCHRYSLER CHANGED THE SUPPLIER OF THE SUBJECT BALL JOINTS FROM TRW TO NEW CASTLE MACHINING & FORGE FOR MY 2000 VEHICLES.MY 2000 DURANGO VEHICLES ACCOUNT FOR 25 OF THE 37 SEPARATION COMPLAINTS.THE UPPER BALL JOINT WAS REDESIGNED IN MY 2003.THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER ASSESS THE ALLEGED DEFECT IN MY 2000-02 DURANGO VEHICLES.
Suspension:front:control Arm
IN JULY 2003, ODI OPENED PE03-032 BASED ON 4 CONSUMER COMPLAINTS ALLEGING SEPARATION OF AN UPPER BALL JOINT.COMPLAINTS ALLEGED AN UNEXPECTED COLLAPSE IN THE FRONT END AND IN SOME OCCASIONS THE BALL JOINT SEPARATION IS ALLEGED TO HAVE RESULTED IN THE WHEEL, BRAKE ROTOR, AND STEERING KNUCKLE SEPARATING FROM THE VEHICLE.SINCE OPENING THE PE, ODI HAS RECEIVED 23 ADDITIONAL COMPLAINTS RELATED TO BALL JOINT SEPARATION. DAIMLERCHRYSLER HAS IDENTIFIED A WEAROUT CONCERN IN THE SUBJECT BALL JOINTS THAT IS BELIEVED TO OCCUR AFTER WATER INTRUSION EVACUATES THE JOINT LUBRICANT.DAIMLERCHRYSLER DOES NOT BELIEVE THE CONDITION POSES AN UNREASONABLE RISK TO SAFETY BECAUSE THE SUSPENSION DESIGN IN THE SUBJECT VEHICLES SIGNIFICANTLY REDUCES THE LIKELIHOOD OF JOINT SEPARATION.OVER 99 PERCENT OF THE FAILURES ARE RELATED TO WORN BALL JOINTS (E.G., NOISE COMPLAINTS).DAIMLERCHRYSLER REVISED THE REPAIR PROCEDURE IN AUGUST 2003 TO ALLOW THE UPPER BALL JOINTS TO BE SERVICED SEPARATELY FROM THE UPPER CONTROL ARM AND REDUCE REPAIR COSTS. DAIMLERCHRYSLER CHANGED THE SUPPLIER OF THE SUBJECT BALL JOINTS FROM TRW TO NEW CASTLE MACHINING & FORGE FOR MY 2000 VEHICLES.MY 2000 DURANGO VEHICLES ACCOUNT FOR 25 OF THE 37 SEPARATION COMPLAINTS.THE UPPER BALL JOINT WAS REDESIGNED IN MY 2003.THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER ASSESS THE ALLEGED DEFECT IN MY 2000-02 DURANGO VEHICLES.
Suspension:front:control Arm:upper Arm
IN JULY 2003, ODI OPENED PE03-032 BASED ON 4 CONSUMER COMPLAINTS ALLEGING SEPARATION OF AN UPPER BALL JOINT.COMPLAINTS ALLEGED AN UNEXPECTED COLLAPSE IN THE FRONT END AND IN SOME OCCASIONS THE BALL JOINT SEPARATION IS ALLEGED TO HAVE RESULTED IN THE WHEEL, BRAKE ROTOR, AND STEERING KNUCKLE SEPARATING FROM THE VEHICLE.SINCE OPENING THE PE, ODI HAS RECEIVED 23 ADDITIONAL COMPLAINTS RELATED TO BALL JOINT SEPARATION. DAIMLERCHRYSLER HAS IDENTIFIED A WEAROUT CONCERN IN THE SUBJECT BALL JOINTS THAT IS BELIEVED TO OCCUR AFTER WATER INTRUSION EVACUATES THE JOINT LUBRICANT.DAIMLERCHRYSLER DOES NOT BELIEVE THE CONDITION POSES AN UNREASONABLE RISK TO SAFETY BECAUSE THE SUSPENSION DESIGN IN THE SUBJECT VEHICLES SIGNIFICANTLY REDUCES THE LIKELIHOOD OF JOINT SEPARATION.OVER 99 PERCENT OF THE FAILURES ARE RELATED TO WORN BALL JOINTS (E.G., NOISE COMPLAINTS).DAIMLERCHRYSLER REVISED THE REPAIR PROCEDURE IN AUGUST 2003 TO ALLOW THE UPPER BALL JOINTS TO BE SERVICED SEPARATELY FROM THE UPPER CONTROL ARM AND REDUCE REPAIR COSTS. DAIMLERCHRYSLER CHANGED THE SUPPLIER OF THE SUBJECT BALL JOINTS FROM TRW TO NEW CASTLE MACHINING & FORGE FOR MY 2000 VEHICLES.MY 2000 DURANGO VEHICLES ACCOUNT FOR 25 OF THE 37 SEPARATION COMPLAINTS.THE UPPER BALL JOINT WAS REDESIGNED IN MY 2003.THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER ASSESS THE ALLEGED DEFECT IN MY 2000-02 DURANGO VEHICLES.
Suspension:front:control Arm:upper Ball Joint
IN JULY 2003, ODI OPENED PE03-032 BASED ON 4 CONSUMER COMPLAINTS ALLEGING SEPARATION OF AN UPPER BALL JOINT.COMPLAINTS ALLEGED AN UNEXPECTED COLLAPSE IN THE FRONT END AND IN SOME OCCASIONS THE BALL JOINT SEPARATION IS ALLEGED TO HAVE RESULTED IN THE WHEEL, BRAKE ROTOR, AND STEERING KNUCKLE SEPARATING FROM THE VEHICLE.SINCE OPENING THE PE, ODI HAS RECEIVED 23 ADDITIONAL COMPLAINTS RELATED TO BALL JOINT SEPARATION. DAIMLERCHRYSLER HAS IDENTIFIED A WEAROUT CONCERN IN THE SUBJECT BALL JOINTS THAT IS BELIEVED TO OCCUR AFTER WATER INTRUSION EVACUATES THE JOINT LUBRICANT.DAIMLERCHRYSLER DOES NOT BELIEVE THE CONDITION POSES AN UNREASONABLE RISK TO SAFETY BECAUSE THE SUSPENSION DESIGN IN THE SUBJECT VEHICLES SIGNIFICANTLY REDUCES THE LIKELIHOOD OF JOINT SEPARATION.OVER 99 PERCENT OF THE FAILURES ARE RELATED TO WORN BALL JOINTS (E.G., NOISE COMPLAINTS).DAIMLERCHRYSLER REVISED THE REPAIR PROCEDURE IN AUGUST 2003 TO ALLOW THE UPPER BALL JOINTS TO BE SERVICED SEPARATELY FROM THE UPPER CONTROL ARM AND REDUCE REPAIR COSTS. DAIMLERCHRYSLER CHANGED THE SUPPLIER OF THE SUBJECT BALL JOINTS FROM TRW TO NEW CASTLE MACHINING & FORGE FOR MY 2000 VEHICLES.MY 2000 DURANGO VEHICLES ACCOUNT FOR 25 OF THE 37 SEPARATION COMPLAINTS.THE UPPER BALL JOINT WAS REDESIGNED IN MY 2003.THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER ASSESS THE ALLEGED DEFECT IN MY 2000-02 DURANGO VEHICLES.
PE02082 · Safety Belt Cinching Latch Plate
Opened Nov 6, 2002 · Closed Apr 23, 2003
Status: closed (inferred from source dates) · Seat Belts
THERE ARE NO INJURIES OR FATALITIES ASSOCIATED WITH THIS ALLEGED DEFECT.WHILE CONDUCTING THIS INVESTIGATION, ODI FOUND THAT THE SUBJECT CINCHES MEET THE LOAD BEARING REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 208, AND THAT MANY OF THE REPORTED FAILURES WERE DUE TO INCORRECT CHILD SAFETY SEAT INSTALLATIONS. ADDITIONALLY, THE REPORT RATE IS LOW (1.60/100K).THE INFORMATION AVAILABLE FAILS TO ESTABLISH THE EXISTENCE OF A DEFECT TREND AT THIS TIME.FURTHER ALLOCATION OF AGENCY RESOURCES TO THIS ISSUE IS UNWARRANTED AND THE PRELIMINARY EVALUATION IS BEING CLOSED.