IllustrationWeld on the back, right side of the driver's seat broke causing the seat to rock while driving. This is the second time this has happened, as we replaced the original seat when this happened to it.
2011 Chevrolet Malibu
Owner reports · Recalls · Investigations
More warning signs than most Malibu years
Owner complaints for the 2011 Chevrolet Malibu are substantially higher than the model-year median of 310.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Malibu years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
650–25K
10125–50K
15950–75K
17575–100K
176100–150K
55150K+
731 reports with mileage · 246 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 235 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 213 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electronic Stability Control (esc). Review the 174 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
40 crash reports17 fire reports30 injury reports
Seats complaints
38 reportsDriver side seat weld has failed causing seat to lean & become unstable. This failure put my entire family at risk.
The contact owns a 2011 Chevrolet Malibu. The contact stated that while driving 55 mph, the weld to the driver’s seat fractured. The contact had pulled over to inspect the damage and was where the seat had started to lean. The contact took the vehicle to an independent mechanic where she was informed that the entire seat needed …
Read full complaint
The contact owns a 2011 Chevrolet Malibu. The contact stated that while driving 55 mph, the weld to the driver’s seat fractured. The contact had pulled over to inspect the damage and was where the seat had started to lean. The contact took the vehicle to an independent mechanic where she was informed that the entire seat needed to be replaced. Neither the dealer nor the manufacturer were notified of the failure. The vehicle was not yet repaired. The failure mileage was approximately 100,000.
HAVE NOTICED THAT THE DRIVER'S SEAT IS LEANING TOWARDS THE BACK AND RIGHT. TOOK IT TO THE DEALERSHIP AND WAS TOLD THERE ARE BROKEN WELDS ON THE FRAME. THIS SHOULD NOT HAPPEN. SEEMS LIKE IT MAKES THE CAR DANGEROUS TO DRIVE.
POWER SEAT WELD AND FRAME BROKE ELECTRICAL PROBLEM CHECK ENGINE LIGHT COMES ON NOTHING WRONG MIRROR POWER ADJUSTING DOES NOT WORK
THE METAL ON SIDE OF SEAT BROKE CAUSING THE SEAT NOT TO BE ABLE TO ADJUST. ALSO, ELECTRICAL PROBLEMS LIGHTER HAD SHORTAGE AND SPEAKER SOUNDS INCREASE AND DECREASE WITH BEING ADJUSTED, AND THE LIGHT FOR THE TIRE PRESSURE REMAIN ON EVEN WHEN THE TIRES HAS SUFFICIENT AIR. I DIDN'T NOTICE AN EXACT TIME THE DEFECT HAPPEN. I JUST NOT…
Read full complaint
THE METAL ON SIDE OF SEAT BROKE CAUSING THE SEAT NOT TO BE ABLE TO ADJUST. ALSO, ELECTRICAL PROBLEMS LIGHTER HAD SHORTAGE AND SPEAKER SOUNDS INCREASE AND DECREASE WITH BEING ADJUSTED, AND THE LIGHT FOR THE TIRE PRESSURE REMAIN ON EVEN WHEN THE TIRES HAS SUFFICIENT AIR. I DIDN'T NOTICE AN EXACT TIME THE DEFECT HAPPEN. I JUST NOTICE THE AFFECTS WHILE DRIVING.
I GOT INTO MY CAR AND THE DRIVER SEAT COLLAPSED ON THE BACK-RIGHT SIDE. AFTER INSPECTION, I FOUND THAT THE WELD BROKE, CAUSING MY CAR TO BE EXTREMELY UNSAFE TO DRIVE! I HAVE FOUND NUMEROUS COMPLAINTS ONLINE AND NUMEROUS COMPLAINTS FILED WITH NHTSA FOR THIS ISSUE. WHY ISN'T AN OFFICIAL INVESTIGATION BEING CONDUCTED REGARDING THI…
Read full complaint
I GOT INTO MY CAR AND THE DRIVER SEAT COLLAPSED ON THE BACK-RIGHT SIDE. AFTER INSPECTION, I FOUND THAT THE WELD BROKE, CAUSING MY CAR TO BE EXTREMELY UNSAFE TO DRIVE! I HAVE FOUND NUMEROUS COMPLAINTS ONLINE AND NUMEROUS COMPLAINTS FILED WITH NHTSA FOR THIS ISSUE. WHY ISN'T AN OFFICIAL INVESTIGATION BEING CONDUCTED REGARDING THIS DEFECT? I FEEL THAT THIS SHOULD BE CONSIDERED A SAFETY RECALL AND GM SHOULD BE RESPONSIBLE FOR THE COST OF THE REPAIRS!
BROKEN WELDS UNDER THE SEAT WHERE THEY SHOULD NEVER BE BROKEN, VERY DANGEROUS! SEAT IS ALL THE WAY DOWN, DRIVER SIDE SEAT HAS COLLASPED
THE SEAT BELTS ON THIS VEHICLE HAVE SOME ISSUES. I WAS INVOLVED IN A WRECK LATELY AND I WAS HURT REALLY BAD FROM THE SEAT BELT ON THE CHEVY . THE SEAT BELT DINTED INTO MY BODY CAUSING SOME REALLY BAD PAIN WHEN THE ACCIDENT OCCURRED.
THE WIRING ON MY VEHICLE HAS ALWAYS BEEN MESSED UP CAUSING MY CHECK LIGHT ENGINE TO STAY ON AT ALL TIMES. I'VE HAD MULTIPLE MACHINISTS LOOK OVER MY VEHICLE AND HAVE SPENT LOTS OF MONEY TRYING TO GET THIS ISSUE FIXED.
Official recalls
319V019000 · Air Bags:frontal:driver Side:inflator Module
Jan 16, 2019
General Motors LLC (GM) is recalling certain 2010-2011 Chevrolet Malibu vehicles. In the event of a crash necessitating deployment of the driver frontal air bag, the air bag inflator may explode due to being overpressurized.
Consequence & remedy
Consequence: If the inflator explodes, sharp metal fragments may strike the driver or other occupants resulting in serious injury or death.
Remedy: GM has notified owners, and dealers will replace the front driver air bag module, free of charge. The recall began February 25, 2019. Owners may contact GM customer service at 1-800-522-9559. GM's number for this recall is N182206630.
15V269000 · Seat Belts
May 8, 2015
General Motors LLC (GM) is recalling certain model year 2011-2012 Chevrolet Malibu vehicles manufactured April 8, 2010, to October 11, 2012. In the affected vehicles, the flexible steel cables that connect the seat belts to the vehicle at the outside of the driver seat and the front passenger seat may be bent from being sat on while entering the vehicle. This repeated bending may result in the cable breaking.
Consequence & remedy
Consequence: If the cable breaks, the seat occupant may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will replace the outboard lap anchor mounting bracket and inspect the flexible steel cable, replacing it as necessary, free of charge. The recall began on November 16, 2015. Owners may contact Chevrolet customer service at 1-800-222-1020. GM's number for this recall is 15031.
14V252000 · Electrical System:wiring; Electronic Stability Control (esc); Exterior Lighting:brake Lights; Exterior Lighting:brake Lights:switch; Vehicle Speed Control:cruise Control
May 14, 2014
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence & remedy
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Additional source detail variants (5)
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Vehicle Speed Control:cruise Control
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Exterior Lighting:brake Lights:switch
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Exterior Lighting:brake Lights
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Electrical System:wiring
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
0No exact-year investigations in this snapshot.