NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
14 reportsClear category filterMileage unknown · Aug 13, 2026
Engine
I am filing an official safety recall non-compliance and documentation fraud complaint against the franchise dealership, BMW of [XXX], regarding their handling of active safety campaigns B110724 (Electric Water Pump) and B120921 (DME Control Unit).Following a severe engine overheating failure related to the water pump recall, bo…
Read full complaint
I am filing an official safety recall non-compliance and documentation fraud complaint against the franchise dealership, BMW of [XXX], regarding their handling of active safety campaigns B110724 (Electric Water Pump) and B120921 (DME Control Unit).Following a severe engine overheating failure related to the water pump recall, both BMW Roadside and the dealership denied my request for a safety tow, forcing me to pay out-of-pocket for a private flatbed. Upon arrival, the dealership held my vehicle for over a week, explicitly withholding the mandatory safety campaign remedies to leverage an aggressive $4,517.18 retail repair quote for secondary turbo coolant lines. My service advisor explicitly left a voicemail stating: "That is why we were waiting to see if you were going to have the work performed before finishing up that 2nd recall."Furthermore, the dealership committed administrative fraud regarding federal disclosure rules. On my final paperwork under Repair Order #XXX, the dealership checked Box #4 on the 'Vehicle Recall Status Disclosure' page, falsely certifying under penalty that the vehicle was 'Not Subject to an Open Safety Recall'—directly contradicting the active campaigns documented on the preceding page. They attempted to coerce my signature on this false document to strip my consumer rights and cover up a blatant safety campaign violation. Due to this hostile environment and fraud, I refused to sign the false disclosure and privately towed my vehicle away to an independent facility. I have full digital and physical PDF copies of the fraudulent paperwork. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11756649
Mileage unknown · Jun 23, 2026
Electrical SystemEngineStructureFire
the vehicle was driven for approximately 30 minutes, operating with zero dashboard warnings or performance indicators. The vehicle was then parked on my property and turned off completely. Approximately two hours and thirty minutes later, the vehicle spontaneously ignited while stationary and unoccupied. The local fire departmen…
Read full complaint
the vehicle was driven for approximately 30 minutes, operating with zero dashboard warnings or performance indicators. The vehicle was then parked on my property and turned off completely. Approximately two hours and thirty minutes later, the vehicle spontaneously ignited while stationary and unoccupied. The local fire department responded and successfully extinguished the blaze. Both physical observations and my home security camera footage confirm that the point of origin was the front right passenger side of the engine compartment. This exact location houses the factory electric water pump and its electrical plug connector, directly matching the failure mechanism detailed in NHTSA Campaign 24V608000, wherein fluid intrusion causes a severe, persistent electrical short circuit capable of igniting a fire hours after the vehicle is parked. The car is completely totaled because of this.
NHTSA ODI #11746090
Mileage unknown · Nov 19, 2025
EngineUnknown Or Other
engine light stays on. had it looked at by mechanic. told the issue is the valtronic actuator. car cuts off when idling. starts back up and drives, when I come to a stop light/stop sign car cuts off again. have contacted BMW North America and a dealership, keep getting the runaround. refer me back to each to contact.
NHTSA ODI #11700340
Mileage unknown · Nov 4, 2025
EngineFire
On the morning of November 2, 2025, around 10:30, I had drove up to the church, parked my car. What I thought was an overheated engine. I decided to go inside the church and deal with what I thought was an overheated engine. About 12-25 minutes later, while inside the church, I got new that a Black BMW was on fire. Someone ha…
Read full complaint
On the morning of November 2, 2025, around 10:30, I had drove up to the church, parked my car. What I thought was an overheated engine. I decided to go inside the church and deal with what I thought was an overheated engine. About 12-25 minutes later, while inside the church, I got new that a Black BMW was on fire. Someone had already called the fire department and police. The engine is totally destroyed, and beyond repair. It is more likely than not the faulty water pump is the causation of the fire. I had no previous maintenance issues with the car. I had not received any notification of a recall, nor was I aware prior to November 2, 2025.
NHTSA ODI #11697381
Mileage unknown · Aug 14, 2025
Engine
This recall has been open for over a year, yet every BMW dealer I have contacted has refused to perform the repair, citing a lack of available parts. I have contacted multiple authorized BMW service centers during this time, and all have confirmed that they cannot complete the recall service because BMW has not supplied the nece…
Read full complaint
This recall has been open for over a year, yet every BMW dealer I have contacted has refused to perform the repair, citing a lack of available parts. I have contacted multiple authorized BMW service centers during this time, and all have confirmed that they cannot complete the recall service because BMW has not supplied the necessary components. This situation has left my vehicle with a known safety defect for an unreasonably long period, creating ongoing safety concerns for me and my passengers. I believe this violates the spirit of federal recall requirements, which are intended to ensure timely and effective remedies for known safety defects.
NHTSA ODI #11680759
Mileage unknown · Jul 30, 2025
Engine
The car shut down by itself while driving. It went from 30 miles/hour to complete stop in 20 feet. I could not put the car in neutral. Any attempts to restart the engine caused smoke to come out of the hood. I had the car towed to the dealer/service. Service told me the engine had seized and they will have to replace the engine…
Read full complaint
The car shut down by itself while driving. It went from 30 miles/hour to complete stop in 20 feet. I could not put the car in neutral. Any attempts to restart the engine caused smoke to come out of the hood. I had the car towed to the dealer/service. Service told me the engine had seized and they will have to replace the engine which would cost me $26, 000.
NHTSA ODI #11677131
Mileage unknown · Jan 31, 2025
Electrical SystemEngineUnknown Or Other
My car is doing exactly as said in the recall that is not available. I'm not driving my bmw due to this problem. Please help
NHTSA ODI #11639909
Mileage unknown · Jan 10, 2025
EngineFuel/propulsion System
I started my bmw up one day after working 16 hours and white thick smoke came from the back tailpipe. Tok it to bmw and they said my car is leaking oil on to the turbo and I need to replace the pump, shocks, valves and others because of this leak. And the car started to issue a transmission fault code on the screen.
NHTSA ODI #11635215
Mileage unknown · Jan 8, 2025
Engine
My vehicle has had an open recall for the engine coolant system and the manufacturer has failed or is unable to remedy this safety recall for your vehicle in a timely manner. As a result, the engine coolant system became damaged and my vehicle is no longer operable. This is my only means of transportation and is causing a serio…
Read full complaint
My vehicle has had an open recall for the engine coolant system and the manufacturer has failed or is unable to remedy this safety recall for your vehicle in a timely manner. As a result, the engine coolant system became damaged and my vehicle is no longer operable. This is my only means of transportation and is causing a serious hardship. I would like the manufacturer to offer an immediate solution.
NHTSA ODI #11634968
Mileage unknown · Dec 3, 2024
Electrical SystemEngine
My vehicle’s engine spews smoke after driving for ten minutes or more. In addition, a toxic odor comes into the cabin when the A/C is on. There are no visible oil or fluid leaks in the engine or the driveway where I park the car. It’s possible that the problem is due to the active recall described below. BMW has failed to find…
Read full complaint
My vehicle’s engine spews smoke after driving for ten minutes or more. In addition, a toxic odor comes into the cabin when the A/C is on. There are no visible oil or fluid leaks in the engine or the driveway where I park the car. It’s possible that the problem is due to the active recall described below. BMW has failed to find a solution in a timely manner to the following NHTSA recall: ENGINE COOLANT PUMP: The electrical connector of the engine coolant pump could become damaged. Small drops of liquid from the positive crankcase ventilation (PCV) system could drip down onto the electrical connector of the pump.
NHTSA ODI #11628698
Official recalls
1Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration