NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
19 reportsClear category filter216,000 miles · Oct 1, 2022
StructureSuspension
I bought a 2007 Toyota Yaris brand new. It's a one owner car with 216000 miles. 5 years ago, I noticed that the side skirt was rusty near the back wheel. Over time, they rusted out. One month ago, while pulling in at the gas station, I heard a crunch. I felt the drivers side of my car go down as well. Got out and drivers rear wh…
Read full complaint
I bought a 2007 Toyota Yaris brand new. It's a one owner car with 216000 miles. 5 years ago, I noticed that the side skirt was rusty near the back wheel. Over time, they rusted out. One month ago, while pulling in at the gas station, I heard a crunch. I felt the drivers side of my car go down as well. Got out and drivers rear wheel was tilted in at the top. The passenger rear wheel was also leaning in at the top. The rear axle was rusted out on the welds. The car was about to crumple up in two. It looks to me like the car had a defect in which water somehow accumulated or ran down the back of that side skirt and rusted it, then the rear axle out. My little economical car is junked out. It may be one of the cheapest cars...well I'm a poor person. I worked my butt off to pay for that and I thought because it was a toyota that it would last. I was wrong. Thank God I only going 5mph. That could easily kill someone. Of course toyota killed all kinds of people a couple of years after I bought that yaris. I knew they were not to be trusted at that point. I thought I was going to keep my yaris forever. I guess I thought wrong.
NHTSA ODI #11487403
65,000 miles · Feb 2, 2018
SeatsStructure
TL* THE CONTACT OWNS A 2007 TOYOTA YARIS. THE CONTACT STATED THAT THE VEHICLE WAS TOWED TO MAGIC TOYOTA (21000 HWY 99, LYNNWOOD, WA 98036, (425) 775-4422) TO BE REPAIRED PER NHTSA CAMPAIGN NUMBERS: 16V340000 (AIR BAGS), 14V168000 (AIR BAGS), AND 14V169000 (SEATS). THE CONTACT STATED THAT THERE WAS EXTREME MOLD IN THE VEHICLE, WH…
Read full complaint
TL* THE CONTACT OWNS A 2007 TOYOTA YARIS. THE CONTACT STATED THAT THE VEHICLE WAS TOWED TO MAGIC TOYOTA (21000 HWY 99, LYNNWOOD, WA 98036, (425) 775-4422) TO BE REPAIRED PER NHTSA CAMPAIGN NUMBERS: 16V340000 (AIR BAGS), 14V168000 (AIR BAGS), AND 14V169000 (SEATS). THE CONTACT STATED THAT THERE WAS EXTREME MOLD IN THE VEHICLE, WHICH MADE IT UNABLE TO BE DRIVEN. THE CONTACT STATED THAT WATER ENTERED THE VEHICLE AND SOAKED ALL THE SEATS, CARPETING, AND SEAT BELTS. THE CONTACT STATED THAT THE CARPET AND FABRIC IN THE VEHICLE HAD EXCESSIVE MOLD. THE CONTACT STATED THAT THERE WAS WATER EVEN IN THE AIR CONDITIONING AND HEATING VENTS. WHILE AT THE DEALER, THE CONTACT REQUESTED THAT THE MECHANIC CHECK FOR THE ENTRY POINTS OF THE WATER, BUT THE DEALER DECLINED THE CONTACT WAS INFORMED THAT THE RECALL REPAIRS COULD NOT BE COMPLETED UNTIL THE MOLD WAS REMOVED FROM INSIDE THE VEHICLE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED AND PROVIDED CASE NUMBER: 1802021186. THE APPROXIMATE FAILURE MILEAGE WAS 65,000.
NHTSA ODI #11066689
109,797 miles · Aug 19, 2015
Exterior LightingSteeringStructureCrash
THE AIRBAG DID NOT DEPLOY EVEN THOUGH I HIT THE FENCE BESIDE THE WINDOW.
NHTSA ODI #10749645
30,000 miles · Jun 16, 2014
Structure
EVERY TIME I USE THE AIR CONDITIONING, THE FRONT PASSENGER CARPET GETS SOAKED. I HAVE PULLED UP THE CARPETING AND CLEANED OUT THE DRAIN TUBE AND TRIED EVERYTHING ELSE SO MANY OTHER OWNERS HAVE TRIED. THIS IS A DESIGN FLAW AND ALMOST EVERY UNPAINTED SURFACE IN THE CAR HAS RUST ON IT. THE MOLD SMELL IS TERRIBLE. THIS IS A VERY…
Read full complaint
EVERY TIME I USE THE AIR CONDITIONING, THE FRONT PASSENGER CARPET GETS SOAKED. I HAVE PULLED UP THE CARPETING AND CLEANED OUT THE DRAIN TUBE AND TRIED EVERYTHING ELSE SO MANY OTHER OWNERS HAVE TRIED. THIS IS A DESIGN FLAW AND ALMOST EVERY UNPAINTED SURFACE IN THE CAR HAS RUST ON IT. THE MOLD SMELL IS TERRIBLE. THIS IS A VERY BAD SITUATION. IN SOUTH CENTRAL INDIANA, WE NEED AIR CONDITIONING FOR A VERY LONG PERIOD. PLEASE HELP US. *TR
NHTSA ODI #10598429
81,213 miles · Nov 13, 2013
Electrical SystemStructure
WATER DRAIN FOR A/C SYSTEM CONDENSER CLOGGED. HAS HAPPENED EVERY SUMMER SINCE PURCHASE IN 2007. WATER FILLS THE DRAIN, AND GETS TRAPPED WITHIN THE UNIT LEADING TO AN OVERFLOW ONTO THE BLOWER AND BLOWER MOTOR SHORTING THE RELAYS. FUSES ARE BLOWN, AND THE BLOWER MOTOR NEEDS REPLACING. IT HAS HAPPENED SEVERAL TIMES. A MOLD BUIL…
Read full complaint
WATER DRAIN FOR A/C SYSTEM CONDENSER CLOGGED. HAS HAPPENED EVERY SUMMER SINCE PURCHASE IN 2007. WATER FILLS THE DRAIN, AND GETS TRAPPED WITHIN THE UNIT LEADING TO AN OVERFLOW ONTO THE BLOWER AND BLOWER MOTOR SHORTING THE RELAYS. FUSES ARE BLOWN, AND THE BLOWER MOTOR NEEDS REPLACING. IT HAS HAPPENED SEVERAL TIMES. A MOLD BUILDUP ALSO OCCURS IN CARPETING LEADING TO A HEALTH HAZARD. *TR
NHTSA ODI #10552136
79,600 miles · Aug 26, 2013
StructureVehicle Speed ControlCrash
ON 16 AUGUST, 2013, WHILE TURNING INTO A GARAGE PARKING SPOT I TOOK MY FOOT OFF THE ACCELERATOR TO PRESS ON THE BRAKE TO COME TO FULL STOP BEFORE THE CONCRETE COLUMN AT THE END OF THE PARKING SPACE WHEN, OF ITS OWN ACCORD, THE CAR SUDDENLY LURCHED FORWARD AT MUCH ACCELERATED SPEED. THE CAR CRASHED INTO THE CONCRETE COLUMN DESTR…
Read full complaint
ON 16 AUGUST, 2013, WHILE TURNING INTO A GARAGE PARKING SPOT I TOOK MY FOOT OFF THE ACCELERATOR TO PRESS ON THE BRAKE TO COME TO FULL STOP BEFORE THE CONCRETE COLUMN AT THE END OF THE PARKING SPACE WHEN, OF ITS OWN ACCORD, THE CAR SUDDENLY LURCHED FORWARD AT MUCH ACCELERATED SPEED. THE CAR CRASHED INTO THE CONCRETE COLUMN DESTROYING THE FRONT LEFT HEAD LIGHTS, ENTIRE FRONT GRILL WORK, AND THE FRAME OF THE DRIVER'S SIDE DOOR WAS BENT SO THE DOOR WOULD NOT BE OPENED. NO AIRBAGS DEPLOYED. ON 20 AUGUST, 2013 MY INSURANCE COMPANY DEEMED THE CAR A TOTAL LOSS. *TR
NHTSA ODI #10537195
170,000 miles · Mar 26, 2013
StructureSuspension
DURING ROLLING BUMPER TO BUMPER TRAFFIC, HEARD A LOUD POP FROM THE FRONT END. AFTERWARDS THE FRONT END KEPT MAKING A ODD GRIND SOUND WHEN I PUT ON THE BRAKES OR WENT OVER A SLIGHT BUMP. TOOK SOME TIME TO FIGURE OUT THAT ONE OF THE BOLTS THAT HOLDS THE PASSENGER SIDE A-ARM WAS GONE, LOOKS LIKE THE BOLT HEAD JUST SHEARED OFF SO…
Read full complaint
DURING ROLLING BUMPER TO BUMPER TRAFFIC, HEARD A LOUD POP FROM THE FRONT END. AFTERWARDS THE FRONT END KEPT MAKING A ODD GRIND SOUND WHEN I PUT ON THE BRAKES OR WENT OVER A SLIGHT BUMP. TOOK SOME TIME TO FIGURE OUT THAT ONE OF THE BOLTS THAT HOLDS THE PASSENGER SIDE A-ARM WAS GONE, LOOKS LIKE THE BOLT HEAD JUST SHEARED OFF SO NOW ALL THE WEIGHT THAT WAS CARRIED BY 3 BOLTS IS BEING MANAGED BY 2. I HAD JUST GOT OFF THE HIGHWAY TOO, GLAD THAT DID NOT POP AT 65 MPH. *TR
NHTSA ODI #10504554
39,800 miles · Oct 25, 2012
StructureInjury
THE TRUNK OF THE VEHICLE DOES NOT STAY OPEN ON ITS OWN , THERE ARE NO SPRINGS OR ANY DEVICE TO KEEP IT OPEN ESPECIALLY IF THE CAR IS ON A INCLINE. MYSELF ,MY PARENTS AND BOYFRIEND HAVE BEEN HIT IN THE BACK OF THE HEAD BY THE TRUNK LID. VERY PAINFUL. DID QUESTION THE DEALERSHIP ABOUT IT AND WAS TOLD THAT WAS HOW THE CAR WAS MADE.…
Read full complaint
THE TRUNK OF THE VEHICLE DOES NOT STAY OPEN ON ITS OWN , THERE ARE NO SPRINGS OR ANY DEVICE TO KEEP IT OPEN ESPECIALLY IF THE CAR IS ON A INCLINE. MYSELF ,MY PARENTS AND BOYFRIEND HAVE BEEN HIT IN THE BACK OF THE HEAD BY THE TRUNK LID. VERY PAINFUL. DID QUESTION THE DEALERSHIP ABOUT IT AND WAS TOLD THAT WAS HOW THE CAR WAS MADE. *TR
NHTSA ODI #10482163
66,950 miles · Jan 26, 2012
StructureSuspension
I AM EXPERIENCING A CLUNKING NOISE COMING FROM THE FRONT OF THE VEHICLE. THE NOISE IS MOST OFTEN HEARD UNDER ACCELERATION OR DECELERATION. THE BOLTS THAT SECURE THE CONTROL ARMS TO THE SUB FRAME ARE CORRODING AND BREAKING OFF, CAUSING SEPARATION OF THE CONTROL ARM FROM THE SUB FRAME AND LOSS OF CONTROL OF THE CAR. *TR
NHTSA ODI #10445483
53,000 miles · Jan 24, 2012
StructureSuspension
I BROUGHT MY 2007 TOYOTA YARIS INTO THE DEALERSHIP TO GET THE BRAKES LOOKED AT AS I WAS HEARING A CLUNKING NOISE GOING OVER UNEVEN ROADS AT SLOW SPEEDS AND I WAS FEELING A STICKING WITH THE BRAKES. THE DEALERSHIP NOTIFIED ME THAT THE BRAKES WERE FINE BUT THAT A BOLT IN THE FRONT CROSS ARM OF THE SUSPENSION HAD RUSTED AND BROKEN …
Read full complaint
I BROUGHT MY 2007 TOYOTA YARIS INTO THE DEALERSHIP TO GET THE BRAKES LOOKED AT AS I WAS HEARING A CLUNKING NOISE GOING OVER UNEVEN ROADS AT SLOW SPEEDS AND I WAS FEELING A STICKING WITH THE BRAKES. THE DEALERSHIP NOTIFIED ME THAT THE BRAKES WERE FINE BUT THAT A BOLT IN THE FRONT CROSS ARM OF THE SUSPENSION HAD RUSTED AND BROKEN OFF. I WAS TOLD THAT THIS WAS A DESIGN FLAW IN THE 2007-2011 YARIS AND THAT THERE WAS A TECHNICAL SERVICE BULLETIN THAT ADVISED ON REPLACING THE WHOLE CROSSMEMBER WITH A NEW DESIGN. THE WARRANTY ONLY COVERED THE CAR UP TO 3 YEARS OR 36000 MILES BUT MY CAR IS 3.5 YEARS AND 53000 MILES. THE COST OF THE PARTS AND REPAIR WAS OVER $2500 AND SINCE IT WAS A SAFETY CONCERN I WAS NOT ALLOWED TO DRIVE THE CAR WITHOUT FIXING IT. THE DEALERSHIP CONTACTED TOYOTA, WHO THEN AGREED TO PAY FOR THE PARTS. I WAS STILL RESPONSIBLE FOR PAYING THE $848 IN LABOR TO REPAIR SOMETHING THAT TOYOTA HAD DESIGNED INCORRECTLY. I HAD TO PAY THE BILL IN ORDER TO GET MY CAR OUT BUT THE DEALERSHIP ENCOURAGED ME TO CONTINUE TO CONTACT TOYOTA DIRECTLY AS THEY AGREED THAT THIS WAS AN ISSUE THAT TOYOTA SHOULD RESOLVE. I CONTACTED TOYOTA USA AND WAS TOLD THAT THEY "TECHNICALLY" DIDN'T HAVE TO DO ANYTHING SINCE IT'S NOT A RECALL AND THAT BECAUSE THEY ALREADY PAID FOR THE PARTS, THAT WAS THE SAME AS ME "AGREEING" THAT THEY DID NOT HAVE TO PAY FOR THE LABOR. TOYOTA SHOULD BE RESPONSIBLE FOR FIXING PROBLEMS ASSOCIATED WITH A DESIGN FLAW IN A MAJOR STRUCTURAL ELEMENT OF THE CAR. A BOLT SHOULDN'T RUST IN LESS THAN 4 YRS, ESPECIALLY WHEN IT'S A SAFETY CONCERN. I THINK THAT WITH TIME, MORE YARIS OWNERS WILL BEGIN TO EXPERIENCE THIS AND IT SHOULD BE LOOKED INTO FURTHER BEFORE SOMEONE IS HURT OR KILLED AS A RESULT OF THIS FAILURE. I HAVE FOUND NUMEROUS COMPLAINTS ONLINE FROM OTHER YARIS OWNERS FOR THIS SAME THING AND THE APA IN CANADA IS REQUESTING TOYOTA CANADA RECALL THE PROBLEM (10/28/11). *TR
NHTSA ODI #10445074
Official recalls
10Oct 17, 2019
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
Additional source detail variants (2)
Air Bags:frontal:passenger Side:inflator Module
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
Air Bags:frontal:driver Side:inflator Module
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
Jan 9, 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2012 Toyota 4Runner, Corolla, Corolla Matrix, Sienna, Yaris, Scion xB, Lexus ES350, GX460, IS-F, IS250, IS350, IS250C, IS350C, and Lexus LFA vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain 2009 Toyota Corolla, Corolla Matrix, Yaris, Yaris HB, Scion xB, Pontiac Vibe, Lexus, ES350, IS250, IS350, and IS-F vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Toyota is recalling certain 2006-2008 Lexus IS250 and IS350, 2007-2008 Lexus ES350, Toyota Yaris, Yaris HB, and 2008 Lexus IS-F and Scion xB vehicles originally sold, or ever registered in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on February 1, 2017. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), H0A (Toyota Zone C), GLG (Lexus Zone A), GLH (Lexus Zone B) and HLA (Lexus Zone C).
May 23, 2016
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Toyota will notify the Toyota and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on December 6, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for interim notification for this campaign are G1P (Toyota Zone A), G1R (Toyota Zone B), G2G (Lexus Zone A), and G2H (Lexus Zone B). Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), GLG (Lexus Zone A), and GLH (Lexus Zone B).
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
Apr 9, 2014
Toyota is recalling certain model year 2006-2010 Yaris vehicles manufactured August 22, 2005, through May 12, 2010, and 2008-2010 Scion xD vehicles manufactured April 4, 2007, through May 12, 2010. In the affected vehicles, the springs used for the seat rails on the driver's seat and the seat rails of the front passenger seat of three-door models may break.
Consequence & remedy
Consequence: If the spring breaks, the seat may not lock in position. In the event of a vehicle crash, the seat could move increasing the risk of injury to the seat occupant.
Remedy: Toyota will notify owners, and dealers will inspect the seat rail, and replace it with a new one, if necessary, free of charge. The recall began on July 3, 2014. Owners may contact Toyota at 1-800-331-4331.
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Jan 29, 2009
TOYOTA IS RECALLING 134,895 MY 2006-2007 YARIS VEHICLES EQUIPPED WITH DRIVER AND FRONT PASSENGER SEAT BELT PRETENSIONERS, WHICH ARE DESIGNED TO BE ACTIVATED IN RESPONSE TO A SEVERE FRONTAL IMPACT. WHEN THE SENSOR DETECTS A SEVERE FRONTAL IMPACT, THE FRONT SEAT BELTS ARE QUICKLY DRAWN BACK BY THE RETRACTORS SO THAT THE BELTS SNUGLY RESTRAIN THE OCCUPANTS. THE INVOLVED VEHICLES CONTAIN A CENTER PILLAR SOUND INSULATOR LOCATED UNDERNEATH EACH FRONT SEAT BELT PRETENSIONER.
Consequence & remedy
Consequence: IN THE EVENT OF SEAT BELT PRETENSIONER DEPLOYMENT, THE GAS GENERATED MAY AFFECT THE SOUND INSULATORS. IN THE WORST CASE, IF THE SOUND INSULATORS IGNITE, THIS CONDITION WILL RESULT IN A POST-COLLISION FIRE.
Remedy: DEALERS WILL MODIFY THE VEHICLE FREE OF CHARGE. THE MODIFICATION WILL ENTAIL REMOVAL OF THE SMALL URETHANE CENTER PILLAR SOUND INSULATORS (SPONGE) UNDERNEATH THE DRIVER AND FRONT PASSENGER SEAT BELT PRETENSIONERS. THE RECALL BEGAN ON JANUARY 28, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA12006 · Power Window Master Switch Fire
Opened Jun 14, 2012 · Closed Feb 12, 2013
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Additional source detail variants (3)
Electrical System
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Structure:body
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
PE12002 · Power Window Master Switch Fire
Opened Feb 6, 2012 · Closed Jun 14, 2012
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Additional source detail variants (3)
Electrical System
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Structure:body
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Illustration