Toyota has a paint problem on the tacomas. The paint is the bright white, .040 . They have painted all 4 doors,both front fenders and the pillars on each side of the windshield. I’m having the same problem on my hood,top of windshield and bed . Toyota refuses to take responsibility for these areas. They call this a customer sati…
Read full complaint
Toyota has a paint problem on the tacomas. The paint is the bright white, .040 . They have painted all 4 doors,both front fenders and the pillars on each side of the windshield. I’m having the same problem on my hood,top of windshield and bed . Toyota refuses to take responsibility for these areas. They call this a customer satisfaction program instead of a recall so they don’t have to paint the whole truck. I have a 25 year old truck that has better paint than it. I just wanted to let you know about this situation. Thanks [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11748666
Mileage unknown · Mar 17, 2026
Structure
Severe clear coat and paint fading on hood, roof and sides of truck.
NHTSA ODI #11724836
Mileage unknown · Dec 3, 2025
Structure
2016 Toyota Tacoma – severe clear coat and paint failure on the hood and roof. The clear coat began peeling in 2022 and has progressively worsened. Large sections of the hood and roof show complete delamination, oxidation, and exposed basecoat. This is a widely reported defect for 2015–2017 Tacomas across multiple paint colors.…
Read full complaint
2016 Toyota Tacoma – severe clear coat and paint failure on the hood and roof. The clear coat began peeling in 2022 and has progressively worsened. Large sections of the hood and roof show complete delamination, oxidation, and exposed basecoat. This is a widely reported defect for 2015–2017 Tacomas across multiple paint colors. Toyota Customer Care confirmed today that my VIN is not included in Customer Support Program 23TE08 and that no goodwill repair would be authorized, even though the defect is identical to the vehicles Toyota acknowledges as affected. This appears to be a manufacturing defect that compromises durability and corrosion resistance. Photos and documentation are available upon request.
NHTSA ODI #11702846
Mileage unknown · Nov 27, 2025
Structure
Paint on hood and roof is fading significantly.
NHTSA ODI #11701789
80,000 miles · Oct 31, 2025
Structure
The contact owns a 2016 Toyota Tacoma. The contact stated that while driving, there was a musty odor coming from the interior of the vehicle. The contact was unable to locate the source of the odor. The contact stated that on a separate occasion, while vacuuming the vehicle, the contact noticed that the carpet and floor mats fro…
Read full complaint
The contact owns a 2016 Toyota Tacoma. The contact stated that while driving, there was a musty odor coming from the interior of the vehicle. The contact was unable to locate the source of the odor. The contact stated that on a separate occasion, while vacuuming the vehicle, the contact noticed that the carpet and floor mats from the rear passenger’s side were wet. The vehicle was taken to the dealer, where it was diagnosed and determined that the rear quarter duct vents had fractured, and water was entering the interior of the vehicle. The vehicle was not repaired due to the cost. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 80,000.
NHTSA ODI #11696786
Mileage unknown · Oct 11, 2024
Structure
The paint on my 2016 Toyota Tacoma is failing after a few years of owning the truck, it has been well maintained and washed but the problem keeps getting worse. I have searched online and it seems to be an issue with white and magnetic grey colored Toyota cars but no recall on magnetic grey paint.
NHTSA ODI #11619340
Mileage unknown · Jul 28, 2024
Structure
At approx 75K miles hood latch popped open. Noticed hood was open while driving on highway. Only the 2nd safety latch was holding it closed. Pulled over to close it but it would not fully latch. Noticed latch had a lot of rust. Did not bother taking it to a dealer or repair shop. Bought an aftermarket latch and easily installed…
Read full complaint
At approx 75K miles hood latch popped open. Noticed hood was open while driving on highway. Only the 2nd safety latch was holding it closed. Pulled over to close it but it would not fully latch. Noticed latch had a lot of rust. Did not bother taking it to a dealer or repair shop. Bought an aftermarket latch and easily installed myself which solved the issue. Very glad hood did not fully fly open which could have been catastrophic.
NHTSA ODI #11604958
Mileage unknown · Jan 9, 2023
StructureUnknown Or OtherInjury
Recent in December wife said there’s a musty odor in truck. While vacuuming carpet on Friday 1/6/23 water came to surface. Searched everywhere for leak and found the 2 vents behind back seats had bad gaskets and leaking bad. After getting access under carpet, passenger side was dry but growing mold and drivers side is holding sl…
Read full complaint
Recent in December wife said there’s a musty odor in truck. While vacuuming carpet on Friday 1/6/23 water came to surface. Searched everywhere for leak and found the 2 vents behind back seats had bad gaskets and leaking bad. After getting access under carpet, passenger side was dry but growing mold and drivers side is holding slimy water. The back seats are a little higher and we’re dry but signs of mold as well. These vents pop out through the cab outward but the bed has to be removed to replace them. I used silicone to seal from inside to stop water intrusion. Dealership no help, report and claim filed with Toyota corporate, insurance company and waiting for response. During the holidays, wife road in my truck several times and ended up spending a week in the hospital due to a fungal infection in her lungs and may be linked to the mold. While on a chat group, Tacoma Owners Group and Tacoma World, there are numerous other owners with the same issue and no help from Toyota.
NHTSA ODI #11500806
Mileage unknown · Nov 13, 2022
Structure
Hood latch, the hood would not fully close and lock! The dashboard warning light would come on indicating the latch was not working. The hood would be open approx 1/2 inch. Tried opening and closing numerous times. Finally, tied the hood closed with a bungee. Went to the local Toyota dealership. They (Service Technician…
Read full complaint
Hood latch, the hood would not fully close and lock! The dashboard warning light would come on indicating the latch was not working. The hood would be open approx 1/2 inch. Tried opening and closing numerous times. Finally, tied the hood closed with a bungee. Went to the local Toyota dealership. They (Service Technician) said he sees often! Sprayed with a solvent. Indicated corrosion around the small spring. A few weeks later, driving and the hood popped, secondary latch kept the hood from fully opening! Dashboard warning light illuminated. I pulled over and tied hood to secure until I could get to the Garage again! Indicated the spring was weak......no repair! Waiting for a disaster to happen at highway speed! Checked Google, and numerous reports by other 2016 owners for same problem!
NHTSA ODI #11493345
Mileage unknown · Sep 15, 2022
StructureUnknown Or Other
2016 TOYOTA TACOMA. CONSUMER WRITES IN REGARD TO PAINT ON THE ROOF OF VEHICLE BEING DISENTEGRATED. THE CONSUMER STATED THE MANUFACTURER WAS NOTIFIED, BUT DECLINED ANY ASSISTANCE.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2011-2016 Toyota Tacoma and 4Runner vehicles equipped with accessory hood scoops installed by SET or SET dealers. The adhesive attaching the hood scoop may weaken, allowing the hood scoop to detach from the vehicle.
Consequence & remedy
Consequence: If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.
Remedy: SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.
Additional source detail variants (2)
Equipment
Southeast Toyota Distributors, LLC (SET) is recalling certain 2011-2016 Toyota Tacoma and 4Runner vehicles equipped with accessory hood scoops installed by SET or SET dealers. The adhesive attaching the hood scoop may weaken, allowing the hood scoop to detach from the vehicle.
Consequence: If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.
Remedy: SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.
Structure:body:hood:hinge And Attachments
Southeast Toyota Distributors, LLC (SET) is recalling certain 2011-2016 Toyota Tacoma and 4Runner vehicles equipped with accessory hood scoops installed by SET or SET dealers. The adhesive attaching the hood scoop may weaken, allowing the hood scoop to detach from the vehicle.
Consequence: If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.
Remedy: SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016-2017 Tacoma vehicles equipped with a six-cylinder engine. The affected vehicles have a crank position sensor that may malfunction, potentially resulting in an engine stall.
Consequence & remedy
Consequence: An engine stall may increase the risk of a crash.
Remedy: Toyota will notify owners, and dealers will replace the crank position sensor with an improved design, free of charge. The recall began July 26, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is H0H.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016-2017 Tacoma vehicles. Oil may leak from the area where the rear differential carrier is assembled to rear axle housing.
Consequence & remedy
Consequence: If the vehicle is operated with an insufficient amount of oil in the rear differential, the differential may seize and cause a loss of control, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will inspect the rear differential for oil leakage. Based on the inspection, dealers will either tightening the fastening nuts or replace the fastening nuts and gasket. If the rear differential components are damaged, the rear differential carrier assembly will be replaced. The repairs will be performed free of charge. The recall June 19, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is H0G.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2016 Tacoma trucks manufactured August 20, 2015, to September 10, 2015. In the affected vehicles, incorrect bolts were used to install the driver's knee air bag module.
Consequence & remedy
Consequence: The incorrect bolts may loosen over time and affect the performance of the driver's knee air bag, increasing the risk of driver injury during a crash that necessitates deployment of the air bags.
Remedy: Toyota will notify owners, and dealers will install the correct driver's knee air bag module mounting bolts, free of charge. The recall began on November 19, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is F0T.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
2016 Toyota Tacoma Problems, Complaints & Recalls | Skip That Year
Illustration