IllustrationTL* THE CONTACT OWNS A 2008 TOYOTA RAV4. THE CONTACT STATED THAT THE WINDSHIELD WIPERS DID NOT WORK. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 113,000.
2008 Toyota RAV4
Owner reports · Recalls · Investigations
More warning signs than most RAV4 years
Owner complaints for the 2008 Toyota RAV4 are substantially higher than the model-year median of 258.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAV4 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
900–25K
6525–50K
9650–75K
8375–100K
74100–150K
25150K+
433 reports with mileage · 142 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 137 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 92 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 81 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
42 crash reports16 fire reports23 injury reports
Visibility complaints
11 reportsDRIVER'S VISOR IS LOOSE. IT WON'T FOLD UP. PLEASE KINDLY HAVE A RECALL ON THIS. THANKS! *TR
TL* THE CONTACT OWNS A 2008 TOYOTA RAV4. THE CONTACT STATED THAT WHILE THE VEHICLE WAS PARKED, THE REAR WINDOW EXPLODED. THE DEALER AND MANUFACTURER WERE NOT NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 53,000. UPDATED 8/27/14*CN THE VEHICLE HAS UNDERGONE 8 RECALLS. UPDATED 09/11/2014 *JS
THE DRIVER SIDE VISOR STARTED SAGGING. FOR A WHILE I COULD PUSH IT BACK UP AND IT WOULD STAY. AFTER A COUPLE MONTHS, I COULD NOT USE IT ON THE SIDE WINDOW, IT JUST HUNG DOWN. IT FINALLY WAS UN-USABLE. TOYOTA HAS REPLACED IT, BUT IT TOOK 3 TRIPS TO THE DEALER TO GET IT REPLACED. I HAD TO DRIVE WITHOUT A VISOR FOR A WEEK …
Read full complaint
THE DRIVER SIDE VISOR STARTED SAGGING. FOR A WHILE I COULD PUSH IT BACK UP AND IT WOULD STAY. AFTER A COUPLE MONTHS, I COULD NOT USE IT ON THE SIDE WINDOW, IT JUST HUNG DOWN. IT FINALLY WAS UN-USABLE. TOYOTA HAS REPLACED IT, BUT IT TOOK 3 TRIPS TO THE DEALER TO GET IT REPLACED. I HAD TO DRIVE WITHOUT A VISOR FOR A WEEK WHILE THEY ORDERED PART. *TR
TL* THE CONTACT OWNS A 2008 TOYOTA RAV4. THE CONTACT STATED THAT THE PASSENGER SIDE WINDOW COULD NOT BE OPENED AND EXHIBITED A BURNING ODOR. THE DEALER WAS NOTIFIED WHO ADVISED THE CONTACT THAT THERE WERE NO RECALLS FOR THE VEHICLE. THE VEHICLE WAS NOT TAKEN TO THE DEALER AND THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEA…
Read full complaint
TL* THE CONTACT OWNS A 2008 TOYOTA RAV4. THE CONTACT STATED THAT THE PASSENGER SIDE WINDOW COULD NOT BE OPENED AND EXHIBITED A BURNING ODOR. THE DEALER WAS NOTIFIED WHO ADVISED THE CONTACT THAT THERE WERE NO RECALLS FOR THE VEHICLE. THE VEHICLE WAS NOT TAKEN TO THE DEALER AND THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 57,000.
MY WIFE AND I WERE DRIVING OUR 2008 TOYOTA RAV4 SPORT NORTH ON I-95 IN VIRGINIA AT EXIT 161 WHEN WE HEARD AN EXPLOSION SOUND ON THE TOP OF THE CAR. I SLID BACK THE MOONROOF COVER ON THE INSIDE OF THE CAR AND COULD SEE THE MOONROOF GLASS WAS BROKEN, IT HAD A HOLE IN THE MIDDLE AND THE REST WAS SHATTERED. WE WERE NOT NEAR A BRID…
Read full complaint
MY WIFE AND I WERE DRIVING OUR 2008 TOYOTA RAV4 SPORT NORTH ON I-95 IN VIRGINIA AT EXIT 161 WHEN WE HEARD AN EXPLOSION SOUND ON THE TOP OF THE CAR. I SLID BACK THE MOONROOF COVER ON THE INSIDE OF THE CAR AND COULD SEE THE MOONROOF GLASS WAS BROKEN, IT HAD A HOLE IN THE MIDDLE AND THE REST WAS SHATTERED. WE WERE NOT NEAR A BRIDGE OR A TOWER OR A TRUCK WHERE SOMETHING COULD HAVE FALLEN ON TOP OF THE CAR. THERE WAS NO OTHER DAMAGE ON THE TOP OF THE CAR. THE GLASS AROUND THE HOLE WAS PUSHED UP LIKE IT HAD EXPLODED. I CALLED THE DEALER AND ASKED IF THEY HAD HEARD OF THIS BEFORE AND IF THERE WAS A RECALL ON IT. THEY SAID NO AND IT WOULD COST OVER $1,000 TO REPLACE. I TOOK IT TO WHERE MY INSURANCE COMPANY TOLD ME TO GET IT FIXED. I FOUND THIS LINK WHERE SOMEBODY ELSE REPORTED THE IDENTICAL PROBLEM HTTP://WWW.ARFC.ORG/COMPLAINTS/2007/TOYOTA/RAV4/?Q=&PAGE=7. *TR
DRIVER SIDE WINDOW CONTROL OPERATES IN THE UP MODE AND CONTINUES TO GO TO THE UP (CLOSED) POSITION AFTER YOUR FINGER IS REMOVED FROM THE CONTROL BUTTON..IN OTHERS AUTOS( US) MADE, THE WINDOW STOPS GOING TO THE CLOSE POSITION WHEN YOUR FINGER IS REMOVED FROM THE CONTROL BUTTON. *TR
DEFROSTER SYSTEM IS WEAK. WHEN THERE IS ICE/SNOW BUILD-UP ALONG EDGES OF WINDSHIELD OR WINDOWS, SYSTEM NEEDS TO BE TURNED TO AND KEPT ON HIGHEST SETTING TO AVOID FOGGING ON THE INSIDE. EVEN AT THIS SETTING, IT HAS TROUBLE CLEARING FOG FROM REAR SIDE WINDOWS. SYSTEM IS PRETTY LOUD AT HIGHEST SETTING SO IT'S HARD TO LISTEN TO R…
Read full complaint
DEFROSTER SYSTEM IS WEAK. WHEN THERE IS ICE/SNOW BUILD-UP ALONG EDGES OF WINDSHIELD OR WINDOWS, SYSTEM NEEDS TO BE TURNED TO AND KEPT ON HIGHEST SETTING TO AVOID FOGGING ON THE INSIDE. EVEN AT THIS SETTING, IT HAS TROUBLE CLEARING FOG FROM REAR SIDE WINDOWS. SYSTEM IS PRETTY LOUD AT HIGHEST SETTING SO IT'S HARD TO LISTEN TO RADIO OR CARRY ON A CONVERSATION. *TR
THE DEFROSTER SYSTEM IS INADEQUATE AND WOULD NOT MELT ICE FROM THE WINDSHIELD UNDER MODERATE TEMPERATURES AND A VERY LIGHT FREEZING MIST. *TR
UNDER CERTAIN WEATHER CONDITIONS (WET SNOW, ICE & FREEZING TEMPS) THE DEFROST SYSTEM WILL NOT KEEP ICE FROM FORMING OVER ABOUT 3/4 OF THE WINDSHIELD. AFTER 10 TO 12 MINUTES OF DRIVING IT IS NECESSARY TO STOP AND SCRAPE ICE FROM THE WINDSHIELD AND WIPERS. IT'S NOT A GOOD IDEA TO STOP ON NARROW MOUNTAIN ROADS IN A BLIZZARD! *TR
Official recalls
1416V596000 · Suspension:rear
Aug 12, 2016
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2011 Toyota RAV4 vehicles manufactured October 31, 2005, to September 7, 2010, and 2010 Lexus HS250h vehicles manufactured July 6, 2009, to August 26, 2010. The affected vehicles have rear suspension arms (rear tie rods) with adjusting lock nuts that may have been improperly tightened after servicing. As a result of being loose, the arm may have thread damage and may rust, possibly leading to the failure of the arm and an abrupt change in the vehicle's alignment.
Consequence & remedy
Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy: Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
16V396000 · Seats:front Assembly:seat Heater/cooler
Jun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
16V096000 · Seat Belts:rear/other
Feb 19, 2016
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2012 RAV4 vehicles manufactured July 28, 2005, to December 19, 2012, and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the event of a frontal collision, the rear seat belts for the outboard seats may be cut by the seat cushion frame.
Consequence & remedy
Consequence: A cut seat belt may not properly restrain the seat occupant, increasing their risk of injury in a crash.
Remedy: Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
15V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
14V743000 · Seats:front Assembly:seat Heater/cooler
Nov 19, 2014
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Consequence & remedy
Consequence: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
14V168000 · Air Bags:frontal:driver Side:inflator Module
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
13V383000 · Suspension:rear
Aug 28, 2013
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment.
Consequence & remedy
Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
12V491000 · Visibility:power Window Devices And Controls
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
12V373000 · Suspension:rear
Aug 2, 2012
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust, leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment.
Consequence & remedy
Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
11V245000 · Air Bags; Air Bags:side/window
Apr 21, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence & remedy
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Additional source detail variants (2)
Air Bags:side/window
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Air Bags
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
11V113000 · Vehicle Speed Control:accelerator Pedal
Feb 24, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 LEXUS LX570, 2003 THROUGH 2009 TOYOTA 4RUNNER, AND 2006 THROUGH 2010 RAV4 VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: THE REMEDY IS NOW AVAILABLE. THE SAFETY RECALL BEGAN EARLY APRIL 2011. THE REMEDY WILL INVOLVE MODIFICATION OR REPLACEMENT OF THE ACCELERATOR PEDAL AND REPLACEMENT OF ANY TOYOTA ALL-WEATHER FLOOR MAT. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331 OR LEXUS AT 1-800-255-3987.
10V035000 · Equipment:other:labels
Feb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
10V036000 · Equipment:other:labels
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
09V223000 · Equipment:other:labels
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA12006 · Power Window Master Switch Fire
Opened Jun 14, 2012 · Closed Feb 12, 2013
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Additional source detail variants (3)
Electrical System
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Structure:body
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
PE12013 · Rear Suspension Arm Assembly Failure
Opened Jun 4, 2012 · Closed Sep 13, 2012
Status: closed (inferred from source dates) · Suspension; Suspension:rear
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Additional source detail variants (4)
Suspension:rear
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Suspension:rear
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Suspension
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Suspension
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
PE12002 · Power Window Master Switch Fire
Opened Feb 6, 2012 · Closed Jun 14, 2012
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Additional source detail variants (3)
Electrical System
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Structure:body
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
RQ10003 · Unintended And Uncontrolled Acceleration
Opened Feb 16, 2010 · Closed Mar 1, 2011
Status: closed (inferred from source dates) · Electrical System:software; Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Additional source detail variants (6)
Electrical System:software
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Electrical System:software
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Electrical System:software
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.