NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
206 reports730,000 miles · Apr 1, 2020
Service BrakesCrash
TL* THE CONTACT OWNED A 2013 TOYOTA HIGHLANDER. THE CONTACT STATED WHILE DRIVING INTO A PARKING SPACE, THE BRAKE PEDAL WAS DEPRESSED HOWEVER, THE BRAKES FAILED TO ENGAGE. DUE TO THE FAILURE, THE VEHICLE WENT OVER THE PARKING SPACE, TRAVELING DOWN A HILL ABOUT 40 FEET DOWN LANDING ON THE FRONT GRILLE OF THE VEHICLE. THE CONTACT S…
Read full complaint
TL* THE CONTACT OWNED A 2013 TOYOTA HIGHLANDER. THE CONTACT STATED WHILE DRIVING INTO A PARKING SPACE, THE BRAKE PEDAL WAS DEPRESSED HOWEVER, THE BRAKES FAILED TO ENGAGE. DUE TO THE FAILURE, THE VEHICLE WENT OVER THE PARKING SPACE, TRAVELING DOWN A HILL ABOUT 40 FEET DOWN LANDING ON THE FRONT GRILLE OF THE VEHICLE. THE CONTACT STATED THAT NO AIR BAGS DEPLOYED. THE CONTACT STATED NO WARNING LIGHT WAS ILLUMINATED. NO POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED TO AN UNKNOWN TOYOTA DEALERSHIP WHERE THEY WERE UNABLE TO DUPLICATE THE FAILURE. THE VEHICLE WAS DEEMED A TOTAL LOSS BY THE DEALERSHIP. THE MANUFACTURER HAD BEEN INFORMED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 73,000.
NHTSA ODI #11319949
Mileage unknown · Jan 31, 2020
Engine
HEAD GASKET CRACKED, LEAKING COOLANT INTO 5TH CYLINDER. THE REASON FOR A PO305 MISFIRE CODE ON READER. AUTO SHOP REMOVED HEAD GASKET AND SAW THAT THE FINISH ON THE ENGINE BLOCK WAS HORRIBLE. THEY CALLED TOYOTA THEMSELVES TO FILE A COMPLAINT AND HAVE THEM REPLACE THAT SIDE OF THE BLOCK. AUTO SHOP DOESN'T FEEL COMFORTABLE REPLACIN…
Read full complaint
HEAD GASKET CRACKED, LEAKING COOLANT INTO 5TH CYLINDER. THE REASON FOR A PO305 MISFIRE CODE ON READER. AUTO SHOP REMOVED HEAD GASKET AND SAW THAT THE FINISH ON THE ENGINE BLOCK WAS HORRIBLE. THEY CALLED TOYOTA THEMSELVES TO FILE A COMPLAINT AND HAVE THEM REPLACE THAT SIDE OF THE BLOCK. AUTO SHOP DOESN'T FEEL COMFORTABLE REPLACING HEAD GASKET WITHOUT TOYOTA FIXING THE FINISH. IF THE FINISH IS AS IS, HEAD GASKET WILL EVENTUALLY CRACK AGAIN. HIGHLANDER WAS BOUGHT BRAND NEW AND ONLY HAS 73K MILES.
NHTSA ODI #11306213
60,000 miles · Jan 15, 2020
Steering
INTERMEDIATE STEERING SHAFT - NOISE BEGAN AROUND 60K MILES AND HAS CONTINUED TO GET WORSE, NOW AT 104K. IF TOYOTA KNOWINGLY MADE A DESIGN CHANGE AND ISSUED A NEW REPLACEMENT PART, RECALL SHOULD BE ISSUED.
NHTSA ODI #11299473
Mileage unknown · Dec 11, 2019
Electrical System
THE VEHICLE WAS PARKED IN OUR DRIVEWAY AND HAS TWICE HAD RATS CHEWING ON THE COOLANT TEMPERATURE CENSOR WIRING. THESE ARE THE ONLY WIRES THEY'VE CHEWED ON SO FAR. I FEEL THE SOY BASED WIRING THAT TOYOTA USES IS TO BLAME SINCE MY NEIGHBORS ARE NOT HAVING PROBLEMS WITH THEIR VEHICLES THAT ARE PARKED OUTDOORS. A CLAIM WITH USAA …
Read full complaint
THE VEHICLE WAS PARKED IN OUR DRIVEWAY AND HAS TWICE HAD RATS CHEWING ON THE COOLANT TEMPERATURE CENSOR WIRING. THESE ARE THE ONLY WIRES THEY'VE CHEWED ON SO FAR. I FEEL THE SOY BASED WIRING THAT TOYOTA USES IS TO BLAME SINCE MY NEIGHBORS ARE NOT HAVING PROBLEMS WITH THEIR VEHICLES THAT ARE PARKED OUTDOORS. A CLAIM WITH USAA HAS BEEN FILED.
NHTSA ODI #11288536
54,000 miles · Dec 3, 2019
Steering
'THUNK'/POPPING NOISE WHEN TURNING THE STEERING WHEEL LEFT OR RIGHT. WAS TOLD TO REPLACE THE INTERMEDIATE STEERING SHAFT, AND LEARNED THAT A NEW ONE WAS DEVELOPED TO FIX THIS PROBLEM IN 2013 BUT NO RECALL OR SAFETY NOTICE WAS SENT TO OWNERS.
NHTSA ODI #11286731
100,000 miles · Nov 25, 2019
Structure
DRIVER DOOR STARTED POPPING AFTER 100,000 MILES WHEN OPENING AND CLOSING. RESEARCHED AND IT'S THE DOOR CHECK. INTERNET RESEARCH SHOWS THIS IS A FAMILIAR PROBLEM THAT NO ONE IS RECALLING.
NHTSA ODI #11282138
88,000 miles · Sep 11, 2019
Steering
WHEN I TURN MY STEERING WHEEL GOING VERY SLOW OR STATIONARY MY STEERING WHEEL MAKES A POPPING SOUNDS AND MY MECHANIC SAYS IT'S THE INTERMEDIATE SHAFT. ITS GETTING WORSE AS I'M PUTTING MILES ON IT. SINCE IT'S A STEERING COMPONENT, IT'S A VERY SERIOUS ISSUE SINCE IF IT FAILS I WILL LOOSE COMPLETE CONTROL OF MY CAR.
NHTSA ODI #11254600
Mileage unknown · Sep 4, 2019
Air BagsCrashInjury
I HAD A FRONT END ACCIDENT ABOUT 2 YEARS AGO AND MY AIRBAGS DID NOT DEPLOY. I CAUSED REAR END DAMAGE TO TWO OTHER VEHICLES. ON SEPT. 2, I HAD ANOTHER FRONT END COLLISION. I RAN INTO A CONCRETE BARRIER THAT HOLDS LIGHT POSTS IN PARKING LOTS. THE ACCIDENT CAUSED ME CHEST, BACK, AND NECK PAIN. THE SEAT BELT TIGHTENED BUT THE AIR …
Read full complaint
I HAD A FRONT END ACCIDENT ABOUT 2 YEARS AGO AND MY AIRBAGS DID NOT DEPLOY. I CAUSED REAR END DAMAGE TO TWO OTHER VEHICLES. ON SEPT. 2, I HAD ANOTHER FRONT END COLLISION. I RAN INTO A CONCRETE BARRIER THAT HOLDS LIGHT POSTS IN PARKING LOTS. THE ACCIDENT CAUSED ME CHEST, BACK, AND NECK PAIN. THE SEAT BELT TIGHTENED BUT THE AIR BAGS NEVER DEPLOYED. I AM STILL IN PAIN DUE TO THIS ACCIDENT.THE FRAME WAS BENT IN FROM THIS COLLISION.
NHTSA ODI #11253078
43,000 miles · Aug 11, 2019
Electrical SystemSteeringVehicle Speed Control
THE DOOR LOCKS STOPPED WORKING AND I WAS FORCED TO PAY TO REPAIR THEM AFTER OWNING CAR FOR LESS THAN 6 MONTHS. THE POWER WINDOWS FAIL TO OPERATE AT RANDOM TIMES. THERE WAS A SIMILAR PROBLEM WITH THE 2010 TOYOTA YARIS WINDOW PANEL. THE CAR JUMPS OR SKIPS WHILE ACCELERATING.
NHTSA ODI #11243113
100,000 miles · Aug 3, 2019
Air BagsElectrical SystemSeats
MAINTENANCE LIGHT IS ON AT ALL TIMES FOR THE FORWARD PASSENGER SEAT, MAKING AIRBAGS USELESS. READ IT CAN POTENTIALLY BE A WIRE. IT HAS BEEN REPORTED ON OTHER VEHICLES. PLEASE INVESTIGATE AND RECALL AS PASSENGERS WILL BE UNSAFE AND COULD HAVE GREAT BODILY HARM WITH THIS DEFECT.
NHTSA ODI #11241464
Official recalls
3Mar 27, 2014
Toyota is recalling certain model year 2013 Highlander vehicles manufactured March 13, 2013, through August 6, 2013. In the affected vehicles, the second row left hand seat may not lock in place when positioned in the forward front or second adjusting position. As such, the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems."
Consequence & remedy
Consequence: If the seat does not lock into the seat track, there may be an increased risk of injury to an occupant in the event of a crash.
Remedy: Toyota will notify owners, and dealers will modify the second row left hand seat so that it will lock into the seat track, free of charge. The recall began on May 21, 2014. Owners may contact Toyota at 1-800-331-4331.
Apr 9, 2013
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Jan 16, 2013
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Illustration