NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
46 reportsClear category filterMileage unknown · Aug 8, 2024
Steering
Steering column cracks, no help from Dealer. Many complaints on internet. Remedy requires expensive new steering column. Defective spindle type bearing defective. The noise is ongoing. It feels like its going to break. Very scary...ongoing doesn't stop. Dealer says wont break just replace if you want to... Toyota Service bul…
Read full complaint
Steering column cracks, no help from Dealer. Many complaints on internet. Remedy requires expensive new steering column. Defective spindle type bearing defective. The noise is ongoing. It feels like its going to break. Very scary...ongoing doesn't stop. Dealer says wont break just replace if you want to... Toyota Service bulletin #T-SB-0034-13 details steering column replacement fix issued on this. I have it. Dealer denies simple joint grease kit maintenance option.
NHTSA ODI #11607205
Mileage unknown · Dec 10, 2021
Steering
When I turn the steering faster than a certain speed, it will lock up for a moment, either turning right or left. Sometimes a light indicating a steering fault lights up on the dash cluster, sometimes not. When the turning of the wheel stops and locks up I cannot turn any more in that direction. I can turn the other way. T…
Read full complaint
When I turn the steering faster than a certain speed, it will lock up for a moment, either turning right or left. Sometimes a light indicating a steering fault lights up on the dash cluster, sometimes not. When the turning of the wheel stops and locks up I cannot turn any more in that direction. I can turn the other way. This has been a problem for sometime and is becoming now worse. Aside from the locking up, justing turning slowly, there is a bit of a whine or low level grind sound in the sound of the steering column. This is a mechanical noise, not the typical whine of the steering pump.
NHTSA ODI #11443325
Mileage unknown · Jul 3, 2021
Steering
- The car was purchased in 2015 used and the steering wheel has made a clunking sound when turning a hard sharp left or right since the day of purchase -While on a road trip of approximately 3,000 miles round trip in June 2021 the steering wheel was adjusted to accommodate my husband's height. It became very loose, with it final…
Read full complaint
- The car was purchased in 2015 used and the steering wheel has made a clunking sound when turning a hard sharp left or right since the day of purchase -While on a road trip of approximately 3,000 miles round trip in June 2021 the steering wheel was adjusted to accommodate my husband's height. It became very loose, with it finally dropping into my husband's lap on the last day of our trip-it was difficult to steer the car -We brought the car in to our dealership the following day where they confirmed we needed a new steering column-the car has not been involved in any accidents nor have the air bags employed -Other than the "clunking" sound there has never been any previous warning that the steering wheel would disengage while driving.
NHTSA ODI #11423336
45,500 miles · Mar 24, 2021
Steering
THERE ARE SOUNDS WHEN SOMETIMES WHEN TURNING, INCLUDING POPING OR SOMETIMES LIKE A WHIRLING SOUND. THE STEERING IS A BIT STIFF SOMETIMES AND NOT EASY TO TURN THE WHEELS, THIS DOES NOT HAPPEN AT ANY SPECIFIC SPEED. I DO NOT HAVE ANY PICTURE OR OTHER DOCUMENT I CAN UPLOAD AS THIS IS NOT PHYSICAL DAMAGE THAT CAN BE PHOTOGRAPHED.
NHTSA ODI #11404623
60,000 miles · Jan 15, 2020
Steering
INTERMEDIATE STEERING SHAFT - NOISE BEGAN AROUND 60K MILES AND HAS CONTINUED TO GET WORSE, NOW AT 104K. IF TOYOTA KNOWINGLY MADE A DESIGN CHANGE AND ISSUED A NEW REPLACEMENT PART, RECALL SHOULD BE ISSUED.
NHTSA ODI #11299473
54,000 miles · Dec 3, 2019
Steering
'THUNK'/POPPING NOISE WHEN TURNING THE STEERING WHEEL LEFT OR RIGHT. WAS TOLD TO REPLACE THE INTERMEDIATE STEERING SHAFT, AND LEARNED THAT A NEW ONE WAS DEVELOPED TO FIX THIS PROBLEM IN 2013 BUT NO RECALL OR SAFETY NOTICE WAS SENT TO OWNERS.
NHTSA ODI #11286731
88,000 miles · Sep 11, 2019
Steering
WHEN I TURN MY STEERING WHEEL GOING VERY SLOW OR STATIONARY MY STEERING WHEEL MAKES A POPPING SOUNDS AND MY MECHANIC SAYS IT'S THE INTERMEDIATE SHAFT. ITS GETTING WORSE AS I'M PUTTING MILES ON IT. SINCE IT'S A STEERING COMPONENT, IT'S A VERY SERIOUS ISSUE SINCE IF IT FAILS I WILL LOOSE COMPLETE CONTROL OF MY CAR.
NHTSA ODI #11254600
43,000 miles · Aug 11, 2019
Electrical SystemSteeringVehicle Speed Control
THE DOOR LOCKS STOPPED WORKING AND I WAS FORCED TO PAY TO REPAIR THEM AFTER OWNING CAR FOR LESS THAN 6 MONTHS. THE POWER WINDOWS FAIL TO OPERATE AT RANDOM TIMES. THERE WAS A SIMILAR PROBLEM WITH THE 2010 TOYOTA YARIS WINDOW PANEL. THE CAR JUMPS OR SKIPS WHILE ACCELERATING.
NHTSA ODI #11243113
33,000 miles · Aug 3, 2019
Steering
MY STEERING MAKES A CLUNKING SOUND, WHICH YOU CAN ACTUALLY FEEL IN THE STEERING WHEEL WHEN IT OCCURS, WHEN TURNING EITHER LEFT OR RIGHT. IT IS INCREASING IN OCCURRENCE AND INTENSITY. IT OCCURS AT ANY SPEED. THIS HAS BEEN GOING ON FOR SEVERAL MONTHS. I TOOK IT TO THE DEALERSHIP AND THEY LUBRICATED SOMETHING, SAYING THERE WAS N…
Read full complaint
MY STEERING MAKES A CLUNKING SOUND, WHICH YOU CAN ACTUALLY FEEL IN THE STEERING WHEEL WHEN IT OCCURS, WHEN TURNING EITHER LEFT OR RIGHT. IT IS INCREASING IN OCCURRENCE AND INTENSITY. IT OCCURS AT ANY SPEED. THIS HAS BEEN GOING ON FOR SEVERAL MONTHS. I TOOK IT TO THE DEALERSHIP AND THEY LUBRICATED SOMETHING, SAYING THERE WAS NO DANGER. SHOULD IT BECOME WORSE BRING IT BACK. IT'S GOING BACK!
NHTSA ODI #11241450
29,493 miles · Jul 10, 2019
Steering
TL* THE CONTACT OWNS A 2013 TOYOTA HIGHLANDER. WHILE DRIVING, A CLUNKING NOISE WAS HEARD COMING FROM THE STEERING WHEEL. IN ADDITION, WHILE MAKING LEFT OR RIGHT TURNS OR WHILE THE VEHICLE WAS STOPPED, THE NOISE GREW LOUDER. THE CONTACT ALSO STATED THAT THE STEERING WHEEL BECAME DIFFICULT TO TURN WHEN THE VEHICLE HAD NOT BEEN DRI…
Read full complaint
TL* THE CONTACT OWNS A 2013 TOYOTA HIGHLANDER. WHILE DRIVING, A CLUNKING NOISE WAS HEARD COMING FROM THE STEERING WHEEL. IN ADDITION, WHILE MAKING LEFT OR RIGHT TURNS OR WHILE THE VEHICLE WAS STOPPED, THE NOISE GREW LOUDER. THE CONTACT ALSO STATED THAT THE STEERING WHEEL BECAME DIFFICULT TO TURN WHEN THE VEHICLE HAD NOT BEEN DRIVEN FOR A COUPLE OF DAYS. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, BUT A FAILURE CODE COULD NOT BE FOUND. THE VEHICLE WAS NOT REPAIRED. THE DEALER AND MANUFACTURER WERE NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 29,493.
NHTSA ODI #11230712
Official recalls
3Mar 27, 2014
Toyota is recalling certain model year 2013 Highlander vehicles manufactured March 13, 2013, through August 6, 2013. In the affected vehicles, the second row left hand seat may not lock in place when positioned in the forward front or second adjusting position. As such, the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems."
Consequence & remedy
Consequence: If the seat does not lock into the seat track, there may be an increased risk of injury to an occupant in the event of a crash.
Remedy: Toyota will notify owners, and dealers will modify the second row left hand seat so that it will lock into the seat track, free of charge. The recall began on May 21, 2014. Owners may contact Toyota at 1-800-331-4331.
Apr 9, 2013
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Jan 16, 2013
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Illustration