1. The 3.5L V6 Engine (2GR-FE) failed due to the subsequent loss of lubrication caused by the rupture of the Oil Cooler Pipe (Rubber component), a manufacturing defect known under TSB T-SB-0201-11 (ZE2 Program). The failed engine is currently available for inspection by request at the independent service center before it is disp…
Read full complaint
1. The 3.5L V6 Engine (2GR-FE) failed due to the subsequent loss of lubrication caused by the rupture of the Oil Cooler Pipe (Rubber component), a manufacturing defect known under TSB T-SB-0201-11 (ZE2 Program). The failed engine is currently available for inspection by request at the independent service center before it is disposed of. 2. The defect causes a sudden and severe loss of engine oil. This creates a high probability of the engine seizing (losing all power) while driving at highway speeds, resulting in a complete loss of propulsion and placing occupants at severe risk of collision. 3. The failure was confirmed, not reproduced. The vehicle was initially diagnosed with misfire codes (P0300, P0301). New spark plugs and ignition coils were installed in an attempt to resolve the issue. As the misfire persisted, the mechanic performed a compression test, confirming catastrophic zero compression failure in cylinders 1 and 2. Professional diagnostics then revealed critical codes: P1603 (ECM Malfunction), P1604 (Startability Malfunction), and P1605 (Rough Idling). These codes confirm a severe internal engine issue, consistent with permanent damage sustained during the oil loss event caused by the ZE2 pipe defect in July 2024. 4. No, not physically inspected by the manufacturer. The manufacturer (Toyota Executive Office Case Manager) was provided with certified documentation of the failure, including the photo of the faulty pipe, maintenance records during our ownership, and the dealership purchase statement for the replacement part. Toyota refused to authorize a physical diagnostic inspection of the failed engine at a dealership before denying goodwill assistance. 5.Yes. The initial lubrication loss event on July 4, 2024, was preceded by a message displayed on the dashboard (followed by a second failure event in October 2025 indicated by a flashing Check Engine light and the Traction Control light).
NHTSA ODI #11701620
Mileage unknown · Jun 25, 2024
Engine
Our car had a major oil leak from the engine Oil Cooler Pipe Manifold at the bottom of the engine (front). My research has concluded that this has been a known issue with various Toyota models with the 2GR-FE engine, however Toyota has not issued a recall and the local dealership has never mentioned it during services. The NHT…
Read full complaint
Our car had a major oil leak from the engine Oil Cooler Pipe Manifold at the bottom of the engine (front). My research has concluded that this has been a known issue with various Toyota models with the 2GR-FE engine, however Toyota has not issued a recall and the local dealership has never mentioned it during services. The NHTSA has known about this issue, however it appears that little to no action has been taken with the vehicle manufacturer or public. The issue concerns a leak that is waiting to happen on all engines with the original Oil Cooler Pipe as it is designed with rubber pipes that degrade over time and even a pin hole oil leak will cause virtually all the engine oil to drain from the engine onto the pavement below and underside of the vehicle including brake components. It is not a matter of “if” but “when” it will happen, and the consequences can leave people stranded with a damaged engine and undriveable vehicle. Severe injury and deaths can and will result due to the ongoing lack of action by the NHTSA and vehicle manufacturer. As an aside, the cost to repair is in the thousands of dollars, unless the owner is fortunate like myself who was able to replace the Oil Cooler Pipe at my own time and cost with the vehicle out of service and significant clean up required. I still don’t know the long-term effects of our engine being almost drained of oil and because of this may now sell the car which was not in our plan. I have added a photo of the original inadequately designed Oil Cooler Pipe and the replacement version purchased from Toyota. Also, the dealership were not interested in doing anything for us. I demand that the NHTSA takes action which is long overdue. Please take this issue seriously
NHTSA ODI #11596623
Mileage unknown · May 25, 2024
EnginePower Train
Dear Sir/Madam, I am writing to file a formal complaint regarding persistent safety issues with my 2011 Toyota Highlander V6 AWD. Specifically, I have experienced significant problems related to the engine timing guide, timing chain, transmission system, which pose a risk to both vehicle occupants and other road users. Vehicle…
Read full complaint
Dear Sir/Madam, I am writing to file a formal complaint regarding persistent safety issues with my 2011 Toyota Highlander V6 AWD. Specifically, I have experienced significant problems related to the engine timing guide, timing chain, transmission system, which pose a risk to both vehicle occupants and other road users. Vehicle Information: Toyota Highlander V6 AWD, VIN: [XXX] Description of the Issue: The transmission in my Highlander has exhibited the following problems: 1) Low engine oil pressure, ticking Noise: There is low engine pressure, faulty guides timing chains, recurring ticking noise. This noise represents issues from the powertrain area and has raised concerns about potential mechanical flaws1. 2) Defective components, slipping Transmission: The transmission surges/slips affecting overall control and safety. This issue has been reported by other Highlander owners as well. Cross-Referencing Other Complaints and Recalls: 3) They did not go far back, Per the NHTSA database, there have been two documented complaints related to transmission issues in the 2011 Toyota Highlander V6 AWD, these complaints align with my experience, however they have not sent me the recall notice. In fact, Toyota has faced recalls and technical service bulletins (TSBs) related to transmission problems in various Highlander models: The 8-speed UA80E/UA80F automatic transmission used in the 2020 Highlander received a TSB for shift flare during wide-open throttle acceleration from 40 – 60 mph and during the upshift from 2nd to 3rd gear. Toyota addressed this issue under warranty1. The 6-speed U660F/U760E automatic transmission, used in earlier Highlander models, was generally reliable. However, the introduction of the 8-speed UA80E/UA80F unit caused initial problems1. Request for Action: Per NHTSA findings please ensure all the models sharing the chassis, model family, part and Toyota transmission oil are included in recall or service campaign. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C.
NHTSA ODI #11590714
Mileage unknown · Sep 4, 2023
Engine
the intake VVT-i gear on 2AR-FE equipped Rav-4s and other Toyota models Has failed after 113k miles. The vehicle is at risk of causing self inflicted damage due to this common issue many toyota owners are facing 2008-2013 highlanders. The part has not been inspected but was diagnosed by a mechanic based on their past experien…
Read full complaint
the intake VVT-i gear on 2AR-FE equipped Rav-4s and other Toyota models Has failed after 113k miles. The vehicle is at risk of causing self inflicted damage due to this common issue many toyota owners are facing 2008-2013 highlanders. The part has not been inspected but was diagnosed by a mechanic based on their past experience with these vehicles and sound. No warnings or dash lights just a terrible metallic rattle upon cold start. This started around 2k miles ago.
NHTSA ODI #11542525
Mileage unknown · Mar 24, 2023
Engine
As my family was driving down Interstate 85 in Atlanta going around 80 MPH a dash notification came on that said "Low Oil Pressure pull over" the notification came on then went away then came back on (car never ran hot). Thankfully we were near an exit so we pulled off and into the first parking lot we could find. There was a hu…
Read full complaint
As my family was driving down Interstate 85 in Atlanta going around 80 MPH a dash notification came on that said "Low Oil Pressure pull over" the notification came on then went away then came back on (car never ran hot). Thankfully we were near an exit so we pulled off and into the first parking lot we could find. There was a huge puddle of oil under the car and smoke coming from the engine. We got our Highlander towed back to our nearest Toyota dealership to our home to be inspected. It was discovered our Engine Oil Cooler Pipe had failed resulting in all of the oil in our car being released from the car. If we hadn't been able to pull over so fast most likely my engine would have seized up and caused a wreck in the middle of the interstate. After doing research on this issue I discover there was a Warranty Enhancement Program done by Toyota on this very part valid through 2021 or 150,000 miles. I have 163,000 miles on my car. I tried to explain to Toyota that like majority of people my car was not driven for 2 years due to covid so they should at the very least expand the warranty. The dealership also told me they couldn't have replaces the part until it failed which from what I can tell of the hundreds of other Toyotas experiencing this same issue there are no warning signs prior to the part failing, you discover it failed by it releasing all your oil while driving at a high rate of speed.
NHTSA ODI #11513598
Mileage unknown · Jun 5, 2022
EnginePower Train
A very common problem and a very expensive fix. There is a rattling noise at cold startup that is coming from the engine. This is a very common problem and many people have complained about this. I don’t know why Toyota is ignoring it. I believe the problem is with the camshaft timing gear but I could be wrong. There should defi…
Read full complaint
A very common problem and a very expensive fix. There is a rattling noise at cold startup that is coming from the engine. This is a very common problem and many people have complained about this. I don’t know why Toyota is ignoring it. I believe the problem is with the camshaft timing gear but I could be wrong. There should definitely be a recall for this issue!
NHTSA ODI #11467662
Mileage unknown · Jun 5, 2022
EngineEngine And Engine CoolingPower Train
My 2011 Toyota Highlander is burning engine oil. So much that I almost got into a major accident on the highway. So what happens is the engine starts burning oil. When the oil level is low the Highlander gives a warning sign saying “low oil pressure” and then the SUV TURNS OFF automatically (even if you’re on the highway). Thous…
Read full complaint
My 2011 Toyota Highlander is burning engine oil. So much that I almost got into a major accident on the highway. So what happens is the engine starts burning oil. When the oil level is low the Highlander gives a warning sign saying “low oil pressure” and then the SUV TURNS OFF automatically (even if you’re on the highway). Thousands of people have complained about this and Toyota is ignoring all the complaints. This issue should be a recall as this is a major problem with highlanders year 2008-2013
NHTSA ODI #11467660
Mileage unknown · Apr 20, 2022
Engine
While driving on the parkway, an oil pressure warning light came on and said to turn off the car. The car immediately started making noise so we pulled onto the shoulder and turned the car off. We were with our 3 children stuck on the side of the very busy road and had to wait for a tow truck. After having it towed our mechanic …
Read full complaint
While driving on the parkway, an oil pressure warning light came on and said to turn off the car. The car immediately started making noise so we pulled onto the shoulder and turned the car off. We were with our 3 children stuck on the side of the very busy road and had to wait for a tow truck. After having it towed our mechanic said it is a known problem with our car. The rubber oil line hose ruptured and we lost all of our oil immediately. The engine could have seized at any moment while driving. Toyota knows of this issue and has since changed it to a metal system but never did a formal recall for this issue. We are currently waiting for it to be fixed so I don't have a bill yet. This seems like something dangerous that could be avoided with a recall. Toyota will not fix this issue.
NHTSA ODI #11461440
Mileage unknown · Feb 20, 2022
Engine
A major and catastrophic oil leak occurred while the car was being driven by my wife on a major thruway during early morning rush hour traffic. The low oil pressure light came on and she was able to maneuver to a parking lot and shut the vehicle off. If the engine had seized due to oil starvation, she may have been involved in a…
Read full complaint
A major and catastrophic oil leak occurred while the car was being driven by my wife on a major thruway during early morning rush hour traffic. The low oil pressure light came on and she was able to maneuver to a parking lot and shut the vehicle off. If the engine had seized due to oil starvation, she may have been involved in a serious accident or seeping oil may have potentially ignited causing a vehicle fire.
NHTSA ODI #11453081
161,000 miles · May 24, 2021
Engine
The contact owns a 2011 TOYOTA Highlander. The contact stated while adding engine oil, the oil would leak from front section of engine. The contact stated that the oil pressure warning light was illuminated. The vehicle was towed to a local dealer where it was in the process of being diagnosed. The manufacturer was not informed …
Read full complaint
The contact owns a 2011 TOYOTA Highlander. The contact stated while adding engine oil, the oil would leak from front section of engine. The contact stated that the oil pressure warning light was illuminated. The vehicle was towed to a local dealer where it was in the process of being diagnosed. The manufacturer was not informed of the failure. The failure mileage was approximately 161,000.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Consequence & remedy
Consequence: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2
EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
2011 Toyota Highlander Problems, Complaints & Recalls | Skip That Year
Illustration