IllustrationWhen starting it would make grinding noise,sounds like metallic noise until the engine oil starts circulating.Dealer said that its normal due to cold starts but this can happen even when the engine is up to temperature.Toyota refuse to remedy the issue.
2009 Toyota Highlander
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Toyota Highlander do not stand out strongly from the model-year median of 186.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Highlander years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
310–25K
1225–50K
1650–75K
1775–100K
19100–150K
10150K+
105 reports with mileage · 29 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 23 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 21 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 20 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
6 crash reports5 fire reports5 injury reports
Engine complaints
23 reportsEngine oil filler cap had interior motor part , melt through while driving , almost hurling all the way through , 2 inch cylindrical part viewed when opening hood to inspect damage . Braking , trac and vsc engaged and motor failed almost dieing , abs allowed brake pedal to go to floor with vehicle just stopping enough to move …
Read full complaint
Engine oil filler cap had interior motor part , melt through while driving , almost hurling all the way through , 2 inch cylindrical part viewed when opening hood to inspect damage . Braking , trac and vsc engaged and motor failed almost dieing , abs allowed brake pedal to go to floor with vehicle just stopping enough to move from traffic . No injuries and No collisions happened due to violent engine combusting or braking disabled , incident happened at 10 mph entering a parking lot .
3 TIMES OVER THE LAST MONTH, WHILE I WAS DRIVING MY VEHICLE, THE CAR SUDDENLY LOST POWER WHILE I WAS DRIVING ON THE HIGHWAY. ALL THE DASHBOARD LIGHTS FLASHED ON, CHECK ENGINE LIGHT AND WARNING LIGHTS ILLUMINATED. THE VEHICLE LOST POWER, THE ACCELERATOR WAS NOT WORKING, AND I WAS JUST BARELY ABLE TO PULL THE CAR OVER TO THE SIDE …
Read full complaint
3 TIMES OVER THE LAST MONTH, WHILE I WAS DRIVING MY VEHICLE, THE CAR SUDDENLY LOST POWER WHILE I WAS DRIVING ON THE HIGHWAY. ALL THE DASHBOARD LIGHTS FLASHED ON, CHECK ENGINE LIGHT AND WARNING LIGHTS ILLUMINATED. THE VEHICLE LOST POWER, THE ACCELERATOR WAS NOT WORKING, AND I WAS JUST BARELY ABLE TO PULL THE CAR OVER TO THE SIDE OF THE ROAD. CAR TURNED OFF AND WAS ABLE TO TURN BACK ON, NOW WITH ILLUMINATED CHECK ENGINE LIGHT AND CHECK HYBRID SYSTEM WARNING LIGHT ILLUMINATED. THIS IS A BIG SAFETY ISSUE AS THE CAR IS LOSING POWER IN THE MIDDLE OF THE ROAD WHILE MY FOOT IS ON THE ACCELERATOR. THE FIRST TIME THIS HAPPENED I WAS ABLE TO PULL A COUPLE CODES FROM THE CODE READER. CODES WERE: U0001 & U0100 THE SECOND AND 3RD TIME THIS HAPPENED THERE WERE NO CODES COMING UP ON THE CODE READER.
BRIEF ENGINE KNOCK/RATTLE NOISE AT COLD STARTUP (1AR2AR) VDS(S):DA41A,ZA3EH WM(S)5TD
OIL COOLER CONNECTED TO ENGINE BLOCK WITH A RUBBER HOSE. HOSE FAILED WITH OIL LEAK WHICH CAUSED LOSS OF ENGINE OIL. CAR TOWED AND REPAIRED BEFORE ENGINE SEIZED. IT APPEARS RUBBER HOSE WAS NOT PROTECTED FROM HEAT OF CATALYTIC CONVERTER AND RUBBER DEGRADED. VEHICLE WAS IN MOTION ON INTERSTATE HIGHWAY WHEN FIRST NOTICED LOSS OF…
Read full complaint
OIL COOLER CONNECTED TO ENGINE BLOCK WITH A RUBBER HOSE. HOSE FAILED WITH OIL LEAK WHICH CAUSED LOSS OF ENGINE OIL. CAR TOWED AND REPAIRED BEFORE ENGINE SEIZED. IT APPEARS RUBBER HOSE WAS NOT PROTECTED FROM HEAT OF CATALYTIC CONVERTER AND RUBBER DEGRADED. VEHICLE WAS IN MOTION ON INTERSTATE HIGHWAY WHEN FIRST NOTICED LOSS OF OIL PRESSURE. ADDED OIL BUT OIL LOSS CONTINUED. WHEN WARNING LIGHT WENT ON SECOND TIME STOPPED VEHICLE AND TOWED TO SERVICE. EVENT OCCURRED ON MAY 15, 2020.
VVTI CAM GEAR ISSUE, MAKING GRINDING NOISE.VEHICLE JUST HIT 60,000 AND OUT OF WARRANTY. EARLIER TSB FROM TOYOTA DIDN'T COVER THIS SINCE THE VEHICLE DIDN'T SHOW ANY SIGNS.
OIL COOLANT LINE BURSTS WHICH CAUSES IMMEDIATE LOSS OF ALL OIL. PROBLEM HAPPENS WHILE VEHICLE IS IN MOTION, AND IN THIS CASE WHILE IN MOTION ON A HIGH TRAFFICKED FREEWAY. FIX COST ABOUT $1,000 OUT OF POCKET. THIS IS A VERY LARGE LEAK WHICH COVERS THE GROUND, ENGINE, AND UNDERCARRIAGE. IF THE OIL LINE RUPTURES WHILE DRIVING, TH…
Read full complaint
OIL COOLANT LINE BURSTS WHICH CAUSES IMMEDIATE LOSS OF ALL OIL. PROBLEM HAPPENS WHILE VEHICLE IS IN MOTION, AND IN THIS CASE WHILE IN MOTION ON A HIGH TRAFFICKED FREEWAY. FIX COST ABOUT $1,000 OUT OF POCKET. THIS IS A VERY LARGE LEAK WHICH COVERS THE GROUND, ENGINE, AND UNDERCARRIAGE. IF THE OIL LINE RUPTURES WHILE DRIVING, THE LOW ENGINE OIL MESSAGE AND ENGINE OIL PRESSURE WARNINGS WILL ILLUMINATE. CONTINUED USE AFTER THESE WARNINGS WILL RESULT IN COMPLETE ENGINE FAILURE DUE TO OIL STARVATION. THE LINE IS KNOWN TO BE DEFECTIVE, AND A REVISED PART HAS BEEN ISSUED BY TOYOTA BUT RECALL HAS NOT BEEN ISSUED. COVERED UNDER A WARRANTY ISSUED BY TOYOTA BUT COVERS UNDER A SHORT TIME FRAME.
I WAS DRIVING DOWN THE INTERSTATE IN WISCONSIN DURING RUSH HOUR WHEN I TOOK OFF MY CRUISE CONTROL TO SLOW DOWN TO TAKE THE NEXT EXIT. I NOTICED AN ABNORMAL DOWN SHIFT WHEN I TOOK OFF THE CRUISE CONTROL. ALMOST IMMEDIATELY THE OIL AND TRACTION CONTROL LIGHTS CAME ON. AS I SLOWED TO THE STOP SIGN AT THE END OF THE EXIT THE DISPLAY…
Read full complaint
I WAS DRIVING DOWN THE INTERSTATE IN WISCONSIN DURING RUSH HOUR WHEN I TOOK OFF MY CRUISE CONTROL TO SLOW DOWN TO TAKE THE NEXT EXIT. I NOTICED AN ABNORMAL DOWN SHIFT WHEN I TOOK OFF THE CRUISE CONTROL. ALMOST IMMEDIATELY THE OIL AND TRACTION CONTROL LIGHTS CAME ON. AS I SLOWED TO THE STOP SIGN AT THE END OF THE EXIT THE DISPLAY SCREEN BEGAN DINGING AND READ LOW OIL PRESSURE AND IMMEDIATELY STOP THE CAR AND TURN OFF THE ENGINE. I IMMEDIATELY PULLED OVER ONCE OUT OF THE WAY OF TRAFFIC AND SHUT DOWN THE CAR. UPON CHECKING THE OIL THERE WAS NONE ON THE DIPSTICK. THERE WAS OIL DRIPPING DOWN FROM THE GRILL ALL UNDERNEATH THE CAR INCLUDING IN THE FRONT TIRE WHEEL WELLS. I ALSO HEARD KNOCKING FROM THE ENGINE, SO I AM CONCERNED THAT THE LIFTERS AND THE TOP END OF THE ENGINE MAY BE COMPROMISED. THIS A KNOWN ISSUE WITH TOYOTA, WHO HAS REFUSED TO ISSUE A RECALL FOR FAULTY OIL LINES AND SEALS. LUCKILY, I WAS AT AN EXIT WHERE I COULD SAFELY PULL OVER BEFORE MORE MAJOR DAMAGE WAS DONE TO THE VEHICLE. MY PERSONAL SAFETY, THE SAFETY OF MY FAMILY AS WELL AS OTHER DRIVERS COULD HAVE COMPROMISED BY THE NEGLECT THAT TOYOTA HAS SHOWN BY CONTINUING TO IGNORE THIS ISSUE.
WHEN VEHICLE IS STATIONARY, ENGINE ALWAYS MAKES STRANGE NOISE UPON INITIAL START.
I WAS TURNING INTO A PARKING LOT AND I STARTED GETTING "LOW OIL PRESSURE" ALERTS ON MY DASHBOARD. I WAS WORRIED IF IT WAS A SENSOR ISSUE AND KEPT MOVING TILL I PARKED MY VEHICLE. UPON FURTHER INVESTIGATION, I SAW THAT OIL HAD STARTED TO DRIP FROM WHERE I HAD TURNED, AND WHEN I PARKED THE CAR THE OIL DRIP GOT BIGGER AND HAD POOLE…
Read full complaint
I WAS TURNING INTO A PARKING LOT AND I STARTED GETTING "LOW OIL PRESSURE" ALERTS ON MY DASHBOARD. I WAS WORRIED IF IT WAS A SENSOR ISSUE AND KEPT MOVING TILL I PARKED MY VEHICLE. UPON FURTHER INVESTIGATION, I SAW THAT OIL HAD STARTED TO DRIP FROM WHERE I HAD TURNED, AND WHEN I PARKED THE CAR THE OIL DRIP GOT BIGGER AND HAD POOLED UNDER THE VEHICLE. BASED ON THE INFORMATION I GOT FROM THE TOYOTA DEALERSHIP, THIS WAS A KNOWN ISSUE WHICH STARTS AS A SMALL LEAK BUT DUE TO PRESSURE, THE OIL COOLER PIPE BURSTS OPEN. THIS KNOWN PROBLEM IS DOCUMENTED HERE: HTTPS://WWW.TOYOHEADQUARTERS.COM/THREADS/2007-2011-TOYOTA-SIENNA-HIGHLANDER-AND-VENZA-ENGINE-OIL-COOLER-PIPE-LEAK-LSC-ZE2.358/ TOYOTA REFUSED TO PAY MY REPAIR BILL AS I WAS OVER THE MILEAGE REQUIREMENT BY 2700 MILES. I CANNOT UNDERSTAND WHY TOYOTA DID NOT CONSIDER THIS A SAFETY ISSUE/RECALL. IF THIS HAD HAPPENED WHILE I WAS DRIVING ON THE HIGHWAY, MY ENGINE COULD HAVE BEEN COMPLETELY DAMAGED AND THE HEAVILY LEAKING OIL COULD HAVE CONTRIBUTED TO AN ACCIDENT(S). THE TOYOTA DEALERSHIP ALSO AGREED WITH ME THAT THIS SHOULD HAVE BEEN A SAFETY RECALL. TOYOTA CLAIMS THEY SENT OUT A LETTER FOR THIS WARRANTY ENHANCEMENT (ZE2) WHICH I NEVER RECEIVED. TOYOTA HAS REFUSED TO ESCALATE THIS ISSUE WITHIN THE COMPANY.
Official recalls
916V396000 · Seats:front Assembly:seat Heater/cooler
Jun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
15V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
14V743000 · Seats:front Assembly:seat Heater/cooler
Nov 19, 2014
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Consequence & remedy
Consequence: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
14V168000 · Air Bags:frontal:driver Side:inflator Module
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
13V014000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seats
Jan 16, 2013
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
10V035000 · Equipment:other:labels
Feb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
10V036000 · Equipment:other:labels
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
10V023000 · Vehicle Speed Control:accelerator Pedal
Jan 27, 2010
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2010 HIGHLANDER, MODEL YEAR 2009-2010 COROLLA, VENZA AND MATRIX PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT. THIS RECALL IS AN EXPANSION OF A CAMPAIGN OF 3.8 MILLION OTHER TOYOTA VEHICLES ANNOUNCED IN 2009 FOR THE SAME ISSUE (SEE 09V-388).
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: TOYOTA WILL MODIFY OR REPLACE THE ACCELERATOR PEDALS ON THE SUBJECT VEHICLES. FLOOR SURFACE MODIFICATIONS ARE ALSO BEING CONSIDERED AND WILL BE INCLUDED FOR ANY MODEL FOR WHICH IT IS DEEMED APPROPRIATE. INITIALLY, DEALERS WILL BE INSTRUCTED ON HOW TO RESHAPE THE ACCELERATOR PEDAL FOR THE REPAIR. AS REPLACEMENT PARTS WITH THE SAME SHAPE AS THE MODIFIED PEDAL BECOME AVAILABLE, THEY WILL BE MADE AVAILABLE TO THE DEALERS FOR THE REPAIR. CUSTOMERS WHO HAVE HAD THE PEDAL RESHAPE REMEDY COMPLETED WILL HAVE THE OPPORTUNITY TO RECEIVE A NEW PEDAL IF THEY DESIRE, AFTER REPLACEMENT PEDALS BECOME AVAILABLE. IN ADDITION, TOYOTA WILL REPLACE ANY TOYOTA ALL-WEATHER FLOOR MAT IN A SUBJECT VEHICLE WITH A NEWLY DESIGNED MAT, FREE OF CHARGE. FOR THOSE CUSTOMERS WHO HAVE THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT BUT DO NOT NEED OR WANT THE NEWLY DESIGNED ALL-WEATHER FLOOR MAT, TOYOTA WILL RECOVER THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT AND REIMBURSE ITS PRICE. THE SAFETY RECALL BEGAN MARCH 30, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
09V223000 · Equipment:other:labels
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.