IllustrationTHE DRIVER SIDE SUNVISOR WILL NOT STAY UP OUT OF PLACE WHEN NOT NEEDED. WHEN DRIVER IS DRIVING ESPECIALLY IF BRAKES ARE USED THE VISOR FALLS BLOCKING VIEW AND IS QUITE DANGEROUS. VISOR WILL NOT STAY UP.
2008 Toyota Highlander
Owner reports · Recalls · Investigations
More warning signs than most Highlander years
Owner complaints for the 2008 Toyota Highlander are substantially higher than the model-year median of 186.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Highlander years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
640–25K
4025–50K
4950–75K
4675–100K
74100–150K
38150K+
311 reports with mileage · 92 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Service Brakes. Review the 66 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 58 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 57 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
44 crash reports14 fire reports24 injury reports
Visibility/wiper complaints
6 reportsTL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER. THE CONTACT STATED THAT THE FRONT DRIVER SIDE WINDOW WOULD SOMETIMES NOT FUNCTION PROPERLY AND THERE WAS A BURNING ODOR WHEN UTILIZED. THERE WERE NO WARNING INDICATORS ILLUMINATED BEFORE THE FAILURE. THE VEHICLE WAS TAKEN TO STEVE LANDERS TOYOTA (10825 COLONEL GLENN RD, LITTLE ROCK,…
Read full complaint
TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER. THE CONTACT STATED THAT THE FRONT DRIVER SIDE WINDOW WOULD SOMETIMES NOT FUNCTION PROPERLY AND THERE WAS A BURNING ODOR WHEN UTILIZED. THERE WERE NO WARNING INDICATORS ILLUMINATED BEFORE THE FAILURE. THE VEHICLE WAS TAKEN TO STEVE LANDERS TOYOTA (10825 COLONEL GLENN RD, LITTLE ROCK, AR 72204) WHERE IT WAS DIAGNOSED THAT THE POWER WINDOW MASTER SWITCH FAILED AND WAS NOT COVERED UNDER WARRANTY. THE VEHICLE WAS NOT REPAIRED. THE CONTACT REFERENCED NHTSA CAMPAIGN NUMBER: 15V689000 (VISIBILITY), BUT THE VIN WAS NOT INCLUDED IN THE RECALL. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 50,000.
SUN VISOR DOE NOT STAY UP.
THE DRIVER SIDE SUN VISOR WILL NOT STAY LOCKED IN THE UP POSITION AND THEREFORE PARTIALLY BLOCKS THE DRIVERS VISION WHILE DRIVING THE VEHICLE.
DRIVER SIDE SUN VISOR DEFECTIVE - IT DOES NOT STAY IN UP POSITION, DROPS DOWN SUDDENLY & BLOCKING THE VISIBILITY OF THE ROAD; DEALER SAID IT IS A COMMON ISSUE BUT NOT ENOUGH COMPLAINS FOR A RECALL. THIS IS AN ACCIDENT PRONE ISSUE THAT WILL CUT OFF THE DRIVER'S VISIBILITY SUDDENLY. *TR
TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER. THE CONTACT STATED THAT WHITE PARTICLES WERE EMITTED THROUGH THE VENTILATION SYSTEM WHILE THE CLIMATE CONTROL WAS ACTIVED. THE VEHICLE WAS NOT TAKEN TO A MECHANIC OR THE DEALER. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS CONTACTED ABOUT THE FAILURE. THE FAILURE MILEAGE WAS A…
Read full complaint
TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER. THE CONTACT STATED THAT WHITE PARTICLES WERE EMITTED THROUGH THE VENTILATION SYSTEM WHILE THE CLIMATE CONTROL WAS ACTIVED. THE VEHICLE WAS NOT TAKEN TO A MECHANIC OR THE DEALER. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS CONTACTED ABOUT THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 76,000.
Official recalls
1116V396000 · Seats:front Assembly:seat Heater/cooler
Jun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
15V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
14V743000 · Seats:front Assembly:seat Heater/cooler
Nov 19, 2014
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Consequence & remedy
Consequence: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
14V168000 · Air Bags:frontal:driver Side:inflator Module
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
12V491000 · Visibility:power Window Devices And Controls
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
11V245000 · Air Bags; Air Bags:side/window
Apr 21, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence & remedy
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Additional source detail variants (2)
Air Bags:side/window
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Air Bags
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
10V035000 · Equipment:other:labels
Feb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
10V036000 · Equipment:other:labels
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
10V023000 · Vehicle Speed Control:accelerator Pedal
Jan 27, 2010
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2010 HIGHLANDER, MODEL YEAR 2009-2010 COROLLA, VENZA AND MATRIX PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT. THIS RECALL IS AN EXPANSION OF A CAMPAIGN OF 3.8 MILLION OTHER TOYOTA VEHICLES ANNOUNCED IN 2009 FOR THE SAME ISSUE (SEE 09V-388).
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: TOYOTA WILL MODIFY OR REPLACE THE ACCELERATOR PEDALS ON THE SUBJECT VEHICLES. FLOOR SURFACE MODIFICATIONS ARE ALSO BEING CONSIDERED AND WILL BE INCLUDED FOR ANY MODEL FOR WHICH IT IS DEEMED APPROPRIATE. INITIALLY, DEALERS WILL BE INSTRUCTED ON HOW TO RESHAPE THE ACCELERATOR PEDAL FOR THE REPAIR. AS REPLACEMENT PARTS WITH THE SAME SHAPE AS THE MODIFIED PEDAL BECOME AVAILABLE, THEY WILL BE MADE AVAILABLE TO THE DEALERS FOR THE REPAIR. CUSTOMERS WHO HAVE HAD THE PEDAL RESHAPE REMEDY COMPLETED WILL HAVE THE OPPORTUNITY TO RECEIVE A NEW PEDAL IF THEY DESIRE, AFTER REPLACEMENT PEDALS BECOME AVAILABLE. IN ADDITION, TOYOTA WILL REPLACE ANY TOYOTA ALL-WEATHER FLOOR MAT IN A SUBJECT VEHICLE WITH A NEWLY DESIGNED MAT, FREE OF CHARGE. FOR THOSE CUSTOMERS WHO HAVE THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT BUT DO NOT NEED OR WANT THE NEWLY DESIGNED ALL-WEATHER FLOOR MAT, TOYOTA WILL RECOVER THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT AND REIMBURSE ITS PRICE. THE SAFETY RECALL BEGAN MARCH 30, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
09V223000 · Equipment:other:labels
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
08V181000 · Seat Belts:rear/other
Apr 18, 2008
TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.
Consequence & remedy
Consequence: HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.
Remedy: DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.