← New search

2008 Toyota Highlander Hybrid

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

180 reports with mileage · 17 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Service Brakes. Review the 94 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electronic Stability Control (esc). Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

6 crash reports4 fire reports4 injury reports

Service Brakes complaints

94 reports
Clear category filter
108,000 miles · Jan 17, 2018
Service Brakes

TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. WHILE DRIVING APPROXIMATELY 35 MPH, THE BRAKES FAILED TO OPERATE WHEN THE BRAKE PEDAL WAS DEPRESSED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE CONTACT MANAGED TO DRIVE THE VEHICLE TO HER RESIDENCE. A MONTH LATER, WHILE DRIVING APPROXIMATELY 30 MPH, THE CHECK VEHICLE S…

Read full complaint

TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. WHILE DRIVING APPROXIMATELY 35 MPH, THE BRAKES FAILED TO OPERATE WHEN THE BRAKE PEDAL WAS DEPRESSED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE CONTACT MANAGED TO DRIVE THE VEHICLE TO HER RESIDENCE. A MONTH LATER, WHILE DRIVING APPROXIMATELY 30 MPH, THE CHECK VEHICLE SYSTEM AND THE BRAKE MALFUNCTION INDICATORS ILLUMINATED. THE VEHICLE WAS PULLED OVER TO THE SIDE OF THE ROAD. THE CONTACT CALLED PUENTE HILLS TOYOTA AT 626-964-7100 (LOCATED AT 17070 GATE AVE, HACIENDA HEIGHTS, CA 91745) AND WAS INFORMED TO TOW THE VEHICLE TO THE SHOP. THE CONTACT DECIDED TO TAKE THE VEHICLE TO TOYOTA OF WHITTIER (14577 E. WHITTIER BLVD, WHITTIER, CA 90605) WHERE IT WAS DIAGNOSED THAT A NEW BRAKE SYSTEM WAS NEEDED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 108,000.

NHTSA ODI #11063335

102,000 miles · Jan 15, 2018
Service BrakesCrash

I WAS DRIVING TO WORK WHEN SUDDENLY MY DASHBOARD DISPLAYED THE ABS VSC WARNING LIGHTS. I BROUGHT MY CAR TO TOYOTA DEALERSHIP FOR THEM TO RUN THE DIAGNOSTICS ON IT, WHICH COST ME $ 100. AFTER WHICH I WAS INFORMED THAT THE ABS ACTUATOR NEEDS TO BE REPLACED FOR ABOUT $4500. SO I ASKED IF THE CAR WAS DRIVABLE AND IF THE BREAKS ARE S…

Read full complaint

I WAS DRIVING TO WORK WHEN SUDDENLY MY DASHBOARD DISPLAYED THE ABS VSC WARNING LIGHTS. I BROUGHT MY CAR TO TOYOTA DEALERSHIP FOR THEM TO RUN THE DIAGNOSTICS ON IT, WHICH COST ME $ 100. AFTER WHICH I WAS INFORMED THAT THE ABS ACTUATOR NEEDS TO BE REPLACED FOR ABOUT $4500. SO I ASKED IF THE CAR WAS DRIVABLE AND IF THE BREAKS ARE STILL OK AND WORKING, THEY SAID IT WAS FINE TO DRIVE BUT TO REPLACE AS SOON AS POSSIBLE. I WAS ABOUT TO GO ON A VACATION SO DIDNT HAVE (THE TIME )OR MONEY TO SPEND ON A PART THAT IN MY MIND SHOULD HAVE BEEN RECALLED BY THE MANUFACTURER. I THEN ATTEMPTED TO CALL TOYOTA TO CHECK FOR ANY RECALLS ON MY MODEL...THEY HAD NONE. AS I WAS COMING BACK FROM MY VACATION, DOING ABOUT 60MPH A LADY PULLED OUT IN FRONT OF MY CAR CAUSING ME TO REAREND HER VEHICLE. MY BREAKS LOCKED UP AND THANKFULLY NO ONE GOT HURT. I AM INTERESTED IN CONTACTING A LAWYER TO SEE WHAT CAN BE DONE.

NHTSA ODI #11062795

137,000 miles · Jan 8, 2018
Electronic Stability Control (esc)Service Brakes

BRAKES STOPPED WORKING WITH LIGHTS COMING ON REQUESTING TO TAKE IT TO DEALERSHIP. DEALERSHIP SAYS IT IS THE ABS ACTUATOR WHICH IS MALFUNCTIONING AND REQUESTING ME TO REPLACE IT AT 3500$. TOYOTA HAS BEEN MAKING THIS PART DEFECTIVE AND HAS BEEN RECALLING THIS FOR SIMILAR MODEL YEARS. 2007 HAS A RECALL. 2008 CAMRY HYBRID HAS A RECA…

Read full complaint

BRAKES STOPPED WORKING WITH LIGHTS COMING ON REQUESTING TO TAKE IT TO DEALERSHIP. DEALERSHIP SAYS IT IS THE ABS ACTUATOR WHICH IS MALFUNCTIONING AND REQUESTING ME TO REPLACE IT AT 3500$. TOYOTA HAS BEEN MAKING THIS PART DEFECTIVE AND HAS BEEN RECALLING THIS FOR SIMILAR MODEL YEARS. 2007 HAS A RECALL. 2008 CAMRY HYBRID HAS A RECALL. THEY SHOULD JUST RECALL THIS PART ACROSS THE BOARD.

NHTSA ODI #11061121

177,000 miles · Dec 22, 2017
Service Brakes

UPON STARTING CAR, BRAKE LIGHT CAME ON, PLUS WARNING MESSAGES SAYING BRAKE MALFUNCTION, CHECK ABS, AND CHECK VSC SYSTEM. TOOK TO DEALER. DEALER SAYS IT NEEDS NEW ABS ACTUATOR WHICH WILL COST $3,300 WITH INSTALLATION. I WAS ALSO TOLD PART IS ON NATIONAL BACKORDER, AND MAY TAKE 1-2 MONTHS TO RECEIVE. DIDN'T TAKE MUCH EFFORT TO…

Read full complaint

UPON STARTING CAR, BRAKE LIGHT CAME ON, PLUS WARNING MESSAGES SAYING BRAKE MALFUNCTION, CHECK ABS, AND CHECK VSC SYSTEM. TOOK TO DEALER. DEALER SAYS IT NEEDS NEW ABS ACTUATOR WHICH WILL COST $3,300 WITH INSTALLATION. I WAS ALSO TOLD PART IS ON NATIONAL BACKORDER, AND MAY TAKE 1-2 MONTHS TO RECEIVE. DIDN'T TAKE MUCH EFFORT TO LEARN ON THE INTERNET THAT THIS SEEMS TO BE A COMMON PROBLEM, AND THAT OTHER TOYOTA CARS AROUND THE SAME PERIOD HAD RECALLS ON THIS PART. WHY NO RECALL ON THIS MODEL AND YEAR?

NHTSA ODI #11056098

Mileage unknown · Dec 2, 2017
Electronic Stability Control (esc)Service Brakes

ABS SYSTEM MALFUNCTION,STATIONARY,WENT ONLINE FOUND NUMEROUS ACCOUNTS

NHTSA ODI #11052028

Mileage unknown · Nov 7, 2017
Service Brakes

MY 2008 HIGHLANDER HYBRID HAS A C1391 ABS ACCUMULATOR TROUBLE LIGHT CLOSE TO A $5000.00 REPAIR. I HAVE NOTICED THE PRIOR 2 YEARS HAVE HAD SAME ISSUE WITH RECALLS AND NUMEROUS COMPLAINTS FOR THIS YEAR. WILL THE NHTSA BE LOOKING INTO THIS?

NHTSA ODI #11044350

147,896 miles · Oct 23, 2017
Electrical SystemService Brakes

I WAS DRIVING IN 295 I HEARING A SOUND COMING FROM THE DASKBOARD AND A LIGHT APPEARED STATED NEED TO CHECK ABS BREAK SYSTEM BY DEALER. I SAID TO MYSELF I'LL HAVE IT CHECK WHEN I GOT HOME. I WAS DOING 65 MILES PER HOUR, I WAS PRESSING BREAK THERE WERE NO BREAK, PUMP THE BREAK SEVERAL TIMES, NO BREAK, I PRESSED THE EMERGENCY BREA…

Read full complaint

I WAS DRIVING IN 295 I HEARING A SOUND COMING FROM THE DASKBOARD AND A LIGHT APPEARED STATED NEED TO CHECK ABS BREAK SYSTEM BY DEALER. I SAID TO MYSELF I'LL HAVE IT CHECK WHEN I GOT HOME. I WAS DOING 65 MILES PER HOUR, I WAS PRESSING BREAK THERE WERE NO BREAK, PUMP THE BREAK SEVERAL TIMES, NO BREAK, I PRESSED THE EMERGENCY BREAK AND THANKS TO THE LORD THE CAR SLOW DOWN AND EVENTUALLY STOP. APPARENTLY DEALER ASKED ME $5,500. TO FIX THIS ISSUE AND I DON'T HAVE THIS TYPE OF MONEY, AND I'M STILL MAKING PAYMENT ON THIS VEHICLE CAN'T EVEN DRIVE; I BELIEVE THIS TYPE OF ISSUE SHOULD BE A RECALL. I NEED HELP PLEASE!!!!! [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

NHTSA ODI #11035649

100,400 miles · Oct 14, 2017
Service Brakes

BRAKE MALFUNCTION ON 2008 HIGHLANDER HYBRID WITH 100,495 MILES: I HAD THE FOLLOWING WARNINGS APPEAR ON THE ELECTRONIC SCREEN - 'ABS SYSTEM MALFUNCTION - PARK CAR IN A SAFE PLACE AND CALL THE DEALER', 'VSC SYSTEM FAILURE', ' BRAKE SYSTEM WARNING'. A LOUD ALARM CAME ON SUDDENLY WHEN I WAS DRIVING THE VEHICLE, AND IS NOW CONSTANT W…

Read full complaint

BRAKE MALFUNCTION ON 2008 HIGHLANDER HYBRID WITH 100,495 MILES: I HAD THE FOLLOWING WARNINGS APPEAR ON THE ELECTRONIC SCREEN - 'ABS SYSTEM MALFUNCTION - PARK CAR IN A SAFE PLACE AND CALL THE DEALER', 'VSC SYSTEM FAILURE', ' BRAKE SYSTEM WARNING'. A LOUD ALARM CAME ON SUDDENLY WHEN I WAS DRIVING THE VEHICLE, AND IS NOW CONSTANT WHEN THE IGNITION 'ON' BUTTON IS PRESSED, (I.E. WHEN CAR IS MOVING OR IN PARK). I NEED TO USE VERY HIGH FOOT PRESSURE TO MAKE THE BRAKES WORK AT ALL AND THIS SITUATION COULD EASILY HAVE CAUSED AN ACCIDENT IF I NEEDED TO STOP SUDDENLY. I READ THE MANY SIMILAR BRAKE RELATED COMPLAINTS ON THE NHTSA AND TOYOTA BLOG PAGES. THE LOCAL TOYOTA DEALER IS CHARGING $2,435 [20-25% OF NET WORTH OF VEHICLE] TO REPLACE THE BRAKE BOOSTER PUMP ASSEMBLY WHICH THEY INDICATE IS ONLY THE FIRST STEP IN DEBUGGING THE ABS/BRAKE/VSC MESSAGES ARE DUE TO. THE REPLACEMENT PART COSTS $1,200 (WITH OVERNIGHT SHIPPING) BUT THE DEALER IS CHARGING $1,781. EVEN AFTER THIS PART IS REPLACED, FIXING THE ISSUE MAY REQUIRE ADDITIONAL PARTS/WORK. I AM VERY DISAPPOINTED WITH TOYOTA US CUSTOMER SERVICE WHO INDICATED THAT THEY CANNOT HELP TO COVER ANY PART OF THIS REPAIR AT ALL, EVEN THOUGH BRAKE FAILURE IS LIFE SAFETY ISSUE. GIVEN THE BRAKE WARRANTY EXTENSION BY TOYOTA FOR 2007-2011 CAMRY AND FOR 2006, 2007 HIGHLANDER HYBRID AND GIVEN THAT THE 2008 MODEL YEAR HIGHLANDER IS BUILT ON THE CAMRY PLATFORM, I AM REQUESTING THAT THE NHTSA STRONGLY URGE TOYOTA TO ISSUE A BRAKE WARRANTY EXTENSION FOR 2008 MODEL YEAR HIGHLANDER HYBRID.

NHTSA ODI #11033348

137,000 miles · Sep 27, 2017
Service BrakesStructureUnknown Or OtherFire

DRIVING APPROXIMATELY 30K / HR ON SEPTEMBER 22, AROUND 6PM. LITTLE TRAFFIC AS THE ROAD LEADS DEEP TO THE COUNTRY. NO RAIN, GREAT VISIBILITY. WE'D JUST STOPPED TO FOLLOW SOMEONE TO A REMOTE LOCATION AND HAD NOT GOTTEN OUT OF THE CAR AT THAT TIME AS THE FRIEND CAME TO THE DRIVER'S SIDE DOOR. A FEW MINUTES LATER, AN ALARM SOUNDED A…

Read full complaint

DRIVING APPROXIMATELY 30K / HR ON SEPTEMBER 22, AROUND 6PM. LITTLE TRAFFIC AS THE ROAD LEADS DEEP TO THE COUNTRY. NO RAIN, GREAT VISIBILITY. WE'D JUST STOPPED TO FOLLOW SOMEONE TO A REMOTE LOCATION AND HAD NOT GOTTEN OUT OF THE CAR AT THAT TIME AS THE FRIEND CAME TO THE DRIVER'S SIDE DOOR. A FEW MINUTES LATER, AN ALARM SOUNDED AND THE INDICATOR DISPLAYED "BRAKE MALFUNCTION". THE BRAKES WERE NOT WORKING AND AT THE SAME MOMENT, SMOKE BEGAN FILLING THE VEHICLE FROM THE FRONT VENTS. AT THIS TIME YOU COULD ALSO SEE SMALL FLAMES FROM THE FRONT HOOD OF THE VEHICLE. WE IMMEDIATELY EXITED THE CAR ONCE IT CAME TO A COMPLETE STOP (FORCED TO PARK POSITION). FLAMES COULD BE SEEN FALLING FROM THE PASSENGER SIDE FRONT END. MY HUSBAND SHUT OFF THE VEHICLE. WE RAN AROUND A NED IN THE ROAD TO GET TO SAFETY. WITHIN MINUTES (5-7 MAX) THE CAR WAS ENGULFED IN FLAMES. THE GENTLEMAN WE WERE FOLLOWING TURNED AROUND TO SEE WHERE WE WERE WHEN HE REALIZED THAT THE CAR WAS IN FLAMES. TOYOTA CES HAS BEEN CONTACTED AS WE WERE HOPING FOR HELP WITH AN INVESTIGATION. WE ARE A MILITARY FAMILY, STATIONED OVERSEAS. THE VEHICLE WAS SHIPPED HERE 2.5 YEARS AGO AT GOVERNMENT EXPENSE ONCE WE RECEIVED NEW ORDERS. TOYOTA HAS BEEN LESS THAN ACCOMMODATING WITH PROVIDING ANY INFORMATION. THIS HAPPENED WITH LITTLE TIME TO GET TO SAFETY. MY HOPE IS INFORMATION CAN BE GATHERED FROM OTHER CONSUMERS THAT MAY HAVE EXPERIENCED SIMILAR SITUATIONS. LIVES COULD POTENTIALLY BE SAVED IF WE WORK TOGETHER TO GET FACTS DOCUMENTED. STATESIDE NUMBER PROVIDED. WE CAN BE REACHED AT +34 642 47 0598

NHTSA ODI #11030100

147,200 miles · Sep 27, 2017
Electronic Stability Control (esc)Service Brakes

TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. WHILE REVERSING AT 5 MPH, THE VSC, CHECK TRACTION CONTROL, ABS, AND BRAKE MALFUNCTION WARNING INDICATORS ILLUMINATED. THE CONTACT WAS STILL ABLE TO DRIVE TO DRIVE TO HIS DESTINATION, BUT THE INDICATORS REMAINED ILLUMINATED. THE LOCAL DEALER WAS NOT CONTACTED OR MADE AWARE OF …

Read full complaint

TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. WHILE REVERSING AT 5 MPH, THE VSC, CHECK TRACTION CONTROL, ABS, AND BRAKE MALFUNCTION WARNING INDICATORS ILLUMINATED. THE CONTACT WAS STILL ABLE TO DRIVE TO DRIVE TO HIS DESTINATION, BUT THE INDICATORS REMAINED ILLUMINATED. THE LOCAL DEALER WAS NOT CONTACTED OR MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS APPROXIMATELY 147,200. ...UPDATED 10/23/17 *BF UPDATED 10/26/2017*JS

NHTSA ODI #11030091

Official recalls

6

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

13V396000 · Hybrid Propulsion System: Inverter

Sep 4, 2013

Toyota is recalling certain model year 2006-2010 Highlander hybrid vehicles manufactured February 16, 2005, through July 29, 2010; and model year 2006-2008 Lexus RX400h vehicles manufactured February 23, 2005, through December 2, 2008. The Intelligent Power Module (IPM) inside the inverter module may contain transistors that have higher operating temperatures than the solder can support and the transistors may be heat damaged by the solder. If this occurs, various warning lamps, including the malfunction indicator lamp, slip indicator light, brake system warning light, and master warning light, will be illuminated on the instrument panel.

Consequence & remedy

Consequence: The vehicle may enter a fail-safe/limp-home mode that limits the drivability of the vehicle. It is possible that the hybrid system will shut down while the vehicle is being driven, causing the vehicle to stall unexpectedly, increasing the risk of a crash.

Remedy: Toyota will notify owners, and dealers will replace the IPM free of charge. Owners may contact Toyota at 1-800-331-4331. Vehicles that had their IPM replaced under recall 11V-342 are not affected by this campaign.

12V491000 · Visibility:power Window Devices And Controls

Oct 10, 2012

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

Consequence & remedy

Consequence: If the switch overheats, it may melt, possibly resulting in a fire.

Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.

11V245000 · Air Bags; Air Bags:side/window

Apr 21, 2011

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.

Consequence & remedy

Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.

Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

Additional source detail variants (2)

Air Bags:side/window

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.

Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.

Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

Air Bags

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.

Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.

Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

09V223000 · Equipment:other:labels

Jun 15, 2009

TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."

Consequence & remedy

Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.

Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.

08V181000 · Seat Belts:rear/other

Apr 18, 2008

TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.

Consequence & remedy

Consequence: HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.

Remedy: DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

5

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

EA18006 · Steering Column Separation

Opened Nov 16, 2018 · Closed Apr 2, 2024

Status: closed (inferred from source dates) · Steering; Steering:column

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Additional source detail variants (2)

Steering:column

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Steering

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

PE18005 · Upper Steering Column Separation

Opened May 4, 2018 · Closed Nov 20, 2018

Status: closed (inferred from source dates) · Steering; Steering:column

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

Additional source detail variants (2)

Steering:column

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

Steering

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

EA12006 · Power Window Master Switch Fire

Opened Jun 14, 2012 · Closed Feb 12, 2013

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Additional source detail variants (3)

Electrical System

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Structure:body

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

PE12002 · Power Window Master Switch Fire

Opened Feb 6, 2012 · Closed Jun 14, 2012

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Additional source detail variants (3)

Electrical System

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Structure:body

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.