← New search

2016 Subaru Outback

Owner reports · Recalls · Investigations

More warning signs than most Outback years

Owner complaints for the 2016 Subaru Outback are substantially higher than the model-year median of 207.5.

About this comparison →

When problems were reported

Mileage at the reported incident

351 reports with mileage · 292 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 309 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Visibility/wiper. Review the 83 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 53 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

22 crash reports3 fire reports8 injury reports

What owners actually said

643 reports
Mileage unknown · Apr 7, 2026
Electrical System

The DCM (Data Communication Module), also referred to as the Starlink telematics module, has failed. This failure is causing a continuous parasitic battery drain, which rapidly depletes the vehicle’s battery even after charging or replacement. The component remains installed in the vehicle and is available for inspection upon re…

Read full complaint

The DCM (Data Communication Module), also referred to as the Starlink telematics module, has failed. This failure is causing a continuous parasitic battery drain, which rapidly depletes the vehicle’s battery even after charging or replacement. The component remains installed in the vehicle and is available for inspection upon request. The failure has resulted in repeated battery drain and loss of vehicle operability. I have experienced a dead battery approximately 4–6 times between September 2025 and present, and the condition has worsened to the point where the vehicle cannot remain running or operable without the battery dying within approximately 5 minutes. This creates a safety risk because the vehicle can become inoperable without warning, increasing the likelihood of being stranded in unsafe conditions or unable to use the vehicle in an emergency. Yes, the issue has been diagnosed and confirmed by a Subaru dealership, which identified the DCM module as failed and requiring replacement. The failure is consistent with a parasitic battery drain caused by the DCM. The vehicle has been inspected by an authorized Subaru dealership.I have also contacted Subaru of America and opened a case requesting assistance with the repair. The primary symptom was repeated battery drain and failure to start beginning around September 2025. The issue progressed over time, with multiple instances of a dead battery, and has now worsened to the point where the battery drains within minutes, preventing normal vehicle operation. There were no consistent warning lights directly identifying the DCM as the cause prior to diagnosis.

NHTSA ODI #11729709

Mileage unknown · Apr 6, 2026
Engine

leak in cam carrier gasket caused large ammounts of smoke to fill engine bay and enter cabin air system. Struggled to breath and vision to an extent was obstructed. when car was parked, smoke continued to fill the engine bay. problem was confirmed by an independent technitian, with the vehicle undergoing a complete inspection ab…

Read full complaint

leak in cam carrier gasket caused large ammounts of smoke to fill engine bay and enter cabin air system. Struggled to breath and vision to an extent was obstructed. when car was parked, smoke continued to fill the engine bay. problem was confirmed by an independent technitian, with the vehicle undergoing a complete inspection about a year ago from the dealership of purchase. no warning lamps turned on until enough oil had seeped from the leak in the liquid silicon gasket, at which point the low oil warning light had turned on.

NHTSA ODI #11729536

Mileage unknown · Mar 25, 2026
EngineFuel/propulsion SystemPower Train

My 2016 Subaru Outback CVT transmission has exhibited an intermittent jerking and grabbing sensation when accelerating from a stop, worse when cold, since at least February 2023. This is a known defect covered under Subaru warranty extension bulletin 16-115-18. February 2023 — An authorized Subaru dealer documented the complaint…

Read full complaint

My 2016 Subaru Outback CVT transmission has exhibited an intermittent jerking and grabbing sensation when accelerating from a stop, worse when cold, since at least February 2023. This is a known defect covered under Subaru warranty extension bulletin 16-115-18. February 2023 — An authorized Subaru dealer documented the complaint in writing. The technician stated the vehicle never warmed up during the test drive and dismissed the concern. The CVT issue was never repaired. I was never informed of Subaru's CVT warranty extension program. February 17 2026 — seven days before my warranty expiration — the same authorized Subaru dealer physically identified and documented a CVT oil pump cover leak. The same jerking complaint was again documented in writing. No repairs were made and the warranty expired one week later. The CVT defect has been physically confirmed by an authorized Subaru dealer within the warranty period and Subaru of America has denied my warranty claim in writing. This issue presents a safety concern. The unpredictable jerking and hesitation when accelerating from a stop creates dangerous situations in traffic, particularly at intersections and when merging. The vehicle is available for inspection upon request. Subaru chose to handle this known widespread defect as a quiet warranty extension rather than a mandatory recall despite hundreds of owners reporting identical symptoms.

NHTSA ODI #11727074

Mileage unknown · Feb 13, 2026
EngineInjury

My 2016 Outback 2.5L model experienced an exhaust noise and/or odor coming from cracks at the bellows section of the front exhaust pipe which includes the catalytic converter. It was diagnosed as leak occurring at the front exhaust pipe. Quoted repair for replacement part only is $2700 plus $1000 labor to repair. Upon investigat…

Read full complaint

My 2016 Outback 2.5L model experienced an exhaust noise and/or odor coming from cracks at the bellows section of the front exhaust pipe which includes the catalytic converter. It was diagnosed as leak occurring at the front exhaust pipe. Quoted repair for replacement part only is $2700 plus $1000 labor to repair. Upon investigation, it was discovered that Subaru Recall WUJ-95 with subject Exhaust Pipe Front (EPF) Bellows Cracking was issued in 2020. My specific VIN was excluded from this recall but I have experienced the exact issue described in the recall. As a result of this situation and exhaust inhalation the car is not able to be driven, this cause breathing issues for me, my wife and our 9 month old baby.

NHTSA ODI #11717808

Mileage unknown · Feb 5, 2026
Steering

Brake light comes on while driving and power steering also locks up..

NHTSA ODI #11715920

Mileage unknown · Jan 4, 2026
Air Bags

Almost after I took ownership of my vehicle in August 2024 from Lexus of Pembroke Pines, I noticed a light on the dashboard that would light intermittently. I purchased an extended warranty for almost four thousand dollars at the time of sale, thank God, as this car has needed a lot of work that I was never told about nor was an…

Read full complaint

Almost after I took ownership of my vehicle in August 2024 from Lexus of Pembroke Pines, I noticed a light on the dashboard that would light intermittently. I purchased an extended warranty for almost four thousand dollars at the time of sale, thank God, as this car has needed a lot of work that I was never told about nor was anything in the CARFAX indicating so many issues. Subaru of Pembroke Pines service department took vehicle in to work on the air bag sensor as that is what seemed to be the issue. In the sixteen months that I have been paying off a loan, the car has been in service for at least a combined ten months plus. They have changed the sensor twice and have changed the harness twice to no avail and that has been covered by the warranty. Now Subaru wants to take apart the car to trace wires to try to find out why the light still won't go out. The warranty company is refusing to take responsibility for the payment for the work and I cannot and will not pay out of my pocket. Subaru wants me to take my car back and drive it. I DO NOT WANT TO DIE FROM A FAULTY AIRBAG. There is something grossly wrong with the vehicle, the service department and especially the warranty company. Please help me get my vehicle fixed without having to be further raped financially. Subaru is trying to get me to purchase yet another vehicle AND I was told by the service lane manager that I should never have been sold that car. IT IS DANGEROUS. My files you are requesting are in my car which is at the dealership.

NHTSA ODI #11708698

Mileage unknown · Dec 31, 2025
Electrical System

I purchased a replacement battery in 2023. In August of 2025, the battery died, requiring a jump start. A local auto parts store checked the battery and it tested within acceptable limits, showing around 513 amps. A private shop confirmed this, and cleaned the battery terminals and cables. The battery functioned well until aroun…

Read full complaint

I purchased a replacement battery in 2023. In August of 2025, the battery died, requiring a jump start. A local auto parts store checked the battery and it tested within acceptable limits, showing around 513 amps. A private shop confirmed this, and cleaned the battery terminals and cables. The battery functioned well until around November 2025, when it again died requiring a jump start. The battery again died in December 2025, about one month later, requiring a jump start.

NHTSA ODI #11707968

Mileage unknown · Dec 21, 2025
Visibility/wiper

1.Windshield crack in the deicing area. Driving on a highway heard a loud boom as if a very big rock hit the car. 30-40 second later there was another boom of normal loudness. At this moment windshield crack has been noticed. The windshield will not be available, replacing it on 12/22/2025 2. Visibility has been affected 3. No,…

Read full complaint

1.Windshield crack in the deicing area. Driving on a highway heard a loud boom as if a very big rock hit the car. 30-40 second later there was another boom of normal loudness. At this moment windshield crack has been noticed. The windshield will not be available, replacing it on 12/22/2025 2. Visibility has been affected 3. No, problem was not reproduced. Dealer representative said that the problem is not covered by Subaru. 4. Windshield was visually inspected by the dealership representative. I will try to collect more data at the windshield replacement shop. 5. There were no symptoms of the problem. N.B - the crack outside is flat, as if no rock hit happened. - I have camera's MP4, where sounds can be heard, 1GB

NHTSA ODI #11706372

50,000 miles · Dec 2, 2025
Electrical System

The contact owns a 2016 Subaru Outback. The contact stated that the horn was inoperable. The vehicle was taken to the local dealer for a routine recall repair, and it was diagnosed and determined that the steering roll connector/clock spring had short-circuited. The vehicle was not repaired. The manufacturer was not notified of …

Read full complaint

The contact owns a 2016 Subaru Outback. The contact stated that the horn was inoperable. The vehicle was taken to the local dealer for a routine recall repair, and it was diagnosed and determined that the steering roll connector/clock spring had short-circuited. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 50,000.

NHTSA ODI #11702493

Mileage unknown · Oct 27, 2025
EngineForward Collision AvoidanceUnknown Or Other

Steering wheel controls frequently fail to work properly on the cruise control system specially the speed control. Also the exhaust system bellow has cracked. The moonroof leaks into the cabin and floor area of the passenger side. Also leaking into the A pillar on the passenger side. I only have a picture of the engine valve cov…

Read full complaint

Steering wheel controls frequently fail to work properly on the cruise control system specially the speed control. Also the exhaust system bellow has cracked. The moonroof leaks into the cabin and floor area of the passenger side. Also leaking into the A pillar on the passenger side. I only have a picture of the engine valve cover that is leaking and had to be replaced. I have video of the exhaust leak coming from the crack in the bellow pipe. Do not have video of the cruise control speed issues as I can’t take a video while driving.

NHTSA ODI #11695930

Official recalls

4

19V910000 · Air Bags: Air Bag/restraint Control Module

Dec 19, 2019

Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.

Consequence & remedy

Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.

Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.

16V292000 · Steering:column

May 11, 2016

Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.

Consequence & remedy

Consequence: The loss of steering ability would increase the risk of a crash.

Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.

15V794000 · Power Train:driveline:differential Unit; Power Train:driveline:driveshaft

Nov 24, 2015

Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.

Consequence & remedy

Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.

Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.

Additional source detail variants (2)

Power Train:driveline:differential Unit

Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.

Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.

Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.

Power Train:driveline:driveshaft

Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.

Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.

Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.

15V502000 · Power Train:automatic Transmission; Power Train:driveline:driveshaft

Aug 10, 2015

Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.

Consequence & remedy

Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.

Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.

Additional source detail variants (2)

Power Train:automatic Transmission

Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.

Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.

Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.

Power Train:driveline:driveshaft

Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.

Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.

Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Go deeper into Subaru Outback problems