THE WINDSHIELD CRACKED IN AUGUST OF 2020 WITHOUT ANY IMPACT OR OUTSIDE CAUSE ACROSS THE MIDDLE OF THE WINDSHIELD ALMOST THE ENTIRE LENGTH OF THE GLASS. I HAD IT REPLACED AT THE DEALERSHIP AND IN APRIL OF 2021 THE NEW WINDSHIELD NOW HAS CRACKED DOWN THE MIDDLE OF THE GLASS. BOTH TIMES THE CRACKS APPEARED OVERNIGHT WITH THE VEHI…
Read full complaint
THE WINDSHIELD CRACKED IN AUGUST OF 2020 WITHOUT ANY IMPACT OR OUTSIDE CAUSE ACROSS THE MIDDLE OF THE WINDSHIELD ALMOST THE ENTIRE LENGTH OF THE GLASS. I HAD IT REPLACED AT THE DEALERSHIP AND IN APRIL OF 2021 THE NEW WINDSHIELD NOW HAS CRACKED DOWN THE MIDDLE OF THE GLASS. BOTH TIMES THE CRACKS APPEARED OVERNIGHT WITH THE VEHICLE IN A PARKED POSITION.
NHTSA ODI #11414573
67,000 miles · Apr 23, 2021
StructureVisibility/wiper
2016 SUBARU OUTBACK. A FOUR-INCH WAVY CRACK ON THE LEFT BOTTOM OF THE WINDSHIELD; A WEEK LATER ANOTHER CRACK OF ABOUT 6 INCHES APPEARED. THE CRACKS OCCURRED WITH THE SUBARU CAR IN MOTION ON A HIGHWAY.
NHTSA ODI #11413587
60,000 miles · Apr 9, 2021
Visibility/wiper
WINDSHIELD BEGAN CRACKING NEAR THE BOTTOM (CLOSE TO THE WINDSHIELD WIPERS) BUT THERE WAS NO ROCK OR DAMAGE TO THE WINDSHIELD THAT PROMPTED THE CRACK. IT JUST APPEARED AND THEN HAS SPREAD ABOUT 2 FEET.
NHTSA ODI #11407190
58,766 miles · Mar 2, 2021
Visibility/wiper
THIS MORNING MY WIFE NOTICED A CRACK IN THE WINDSHIELD OF OUR 2016 3.6R SUBARU OUTBACK PURCHASED 3/2016. IT ORIGINATES AT THE BASE OF THE WINDSHIELD, PASSES OVER THE 6 RED DEFROSTER WIRES BELOW THE WINDSHIELD, AND EXTENDS ~10" UP ON THE DRIVERS SIDE TOWARD THE REAR VIEW MIRROR. THERE ARE NO PITS ETC., THIS CRACK ORIGINATED ON …
Read full complaint
THIS MORNING MY WIFE NOTICED A CRACK IN THE WINDSHIELD OF OUR 2016 3.6R SUBARU OUTBACK PURCHASED 3/2016. IT ORIGINATES AT THE BASE OF THE WINDSHIELD, PASSES OVER THE 6 RED DEFROSTER WIRES BELOW THE WINDSHIELD, AND EXTENDS ~10" UP ON THE DRIVERS SIDE TOWARD THE REAR VIEW MIRROR. THERE ARE NO PITS ETC., THIS CRACK ORIGINATED ON THE INSIDE OF THE WINDSHIELD. THIS CRACK PERFECTLY MATCHES THE CRACK PATTERN AND DESCRIPTION IDENTIFIED IN SUBARU SERVICE BULLETIN 12-192-15R, REVISED 11/19/15. THAT BULLETIN WAS ISSUED AS A RESULT OF SUBARU'S LOOSING A LAWSUIT IN CALIFORNIA REGARDING BROKEN GLASS WINDSHIELDS BECAUSE OF MANUFACTURING DEFECT. UNFORTUNATELY SUBARU IS ONLY REPLACING DEFECTIVE GLASS ON OUTBACKS UP TO VIN G3222455/G3210476. OUR MANUFACTURING VIN IS EARLY 2016, AND THE JUDGE IN THE CASE DID NOT EXTEND JUDGMENT AGAINST SUBARY TO COVER OUR OUTBACK. THIS IS EXACTLY THE SAME PROBLEM WITH OUR OUTBACK AS FOR THE CALIFORNIA CASE. HERE IN NEW JERSEY WE HAVE BEEN HAVING SEVERAL WEEKS OF HARSH WEATHER, OUTSIDE TEMPERATURE ~20 DEGREES F IN THE MORNING. THE OUTBACK IS GARAGED, IT IS A WARM GARAGE. EVEN THOUGH THIS IS A 2016, WE ASSUME THE EXTREME IS A FACTOR. THIS IS NOT A STONE HIT PROBLEM, ALL THE DRIVING IS NORTHERN NJ SURBURBAN ROADS, NOT HIGHWAY DRIVING. WE SEE MANY MANY COMPLAINTS DEFINITELY A MANUFACTURING ISSUE. ATTACHING A PHOTO OF CRACK. I RUN MY FINGER OVER THE CRACK AND ACTUALLY CAN'T FEEL ANYTHING, NO DINGS, NOTHING.
NHTSA ODI #11398774
45,000 miles · Jan 19, 2021
Visibility/wiper
I DROVE MY CAR TO SKI. I PARKED MY CAR. THE SNOW ACCUMULATED ON WINDSHIELD. AND THEN I FOUND THE WINDSHIELD HAS A LONG CRACK.
NHTSA ODI #11388831
60,927 miles · Jan 5, 2021
Visibility/wiper
2016 SUBARU OUTBACK'S FRONT WINDSHIELD CRACKED FOR NO APPARENT REASONS
NHTSA ODI #11386614
49,000 miles · Sep 28, 2020
Visibility/wiper
II WAS DRIVING ON AN OPEN HIGHWAY WITH NO CARS IN CLOSE VICINITY WHEN WINDSHIELD CRACKED FOR NO APPARENT REASON. CRACK WAS ON DRIVER SIDE NEAR EDGE ABOUT 12 INCHES LONG. ON INVESTIGATION, THERE WERE NO NICKS OR PITS IN THE WINDSHIELD, JUST THE CRACK. WHEN THE WINDSHIELD WAS BEING REPLACED, THE TECHNICIAN STATED THAT IT WAS WI…
Read full complaint
II WAS DRIVING ON AN OPEN HIGHWAY WITH NO CARS IN CLOSE VICINITY WHEN WINDSHIELD CRACKED FOR NO APPARENT REASON. CRACK WAS ON DRIVER SIDE NEAR EDGE ABOUT 12 INCHES LONG. ON INVESTIGATION, THERE WERE NO NICKS OR PITS IN THE WINDSHIELD, JUST THE CRACK. WHEN THE WINDSHIELD WAS BEING REPLACED, THE TECHNICIAN STATED THAT IT WAS WIERD THAT A SIMILAR CRACK DEVELOPED ON THE PASSENGER SIDE OF THE WINDSHIELD AS HE WAS REMOVING THE SHIELD FROM THE CAR.
NHTSA ODI #11361475
44,000 miles · Sep 21, 2020
Visibility/wiper
FRONT WINDSHIELD CRACKED, ORIGINATING FROM THE EDGE OF THE WINDOW, ABOUT 2 YEARS AGO WHILE PARKED WITHOUT ANY OVERHANGING HAZARDS OR ADVERSE WEATHER. THERE IS NO ASSOCIATED GLASS 'DING' FROM AN IMPACT. I BELIEVE THIS IS THE SAME PROBLEM THAT LED TO A LAWSUIT AGAINST SUBARU INVOLVING 2015-2016 OUTBACK'S.
NHTSA ODI #11360352
56,210 miles · Sep 13, 2020
Visibility/wiper
WE PURCHASED A CAR BRAND NEW IN SAVANNAH, GA AND SINCE HAVE REPLACED WINDSHIELD THREE TIMES. IT HAS A SMALL CRACK AGAIN. ALL OUR REPLACEMENTS OCCURRED AGAINST OUR INSURANCE. OUR COVERAGE HAS INCREASE IN PREMIUMS. PREVIOUSLY, I NEVER HAD AN ISSUE WITH WINDSHIELD CRACKED ON REGULAR OCCURRENCE. ANOTHER ISSUE - WHEN IT RAINS THE …
Read full complaint
WE PURCHASED A CAR BRAND NEW IN SAVANNAH, GA AND SINCE HAVE REPLACED WINDSHIELD THREE TIMES. IT HAS A SMALL CRACK AGAIN. ALL OUR REPLACEMENTS OCCURRED AGAINST OUR INSURANCE. OUR COVERAGE HAS INCREASE IN PREMIUMS. PREVIOUSLY, I NEVER HAD AN ISSUE WITH WINDSHIELD CRACKED ON REGULAR OCCURRENCE. ANOTHER ISSUE - WHEN IT RAINS THE VISIBILITY IS EXTREMELY POOR. DESPITE I BUY THE EXPENSIVE WIPERS TO REPLACE THEM AT LEAST ONCE IN 12 MONTHS UNABLE TO ADJUST/INCREASE THE WIPER SPEED FOR THE HEAVY RAIN MAKES THE DRIVING EXTREMELY DANGEROUS. OPTIONAL EYESIGHT WHICH WAS ADDED AS AN OPTION IS SHUTS ITSELF DUE TO THE HEAVY RAIN AND IS NO HELP. EYESIGHT IS ALSO UNDERPERFORM WHAT WAS PROMISED BY MANUFACTURER. ALL ABOVE APPLIES FOR VEHICLE IN MOTION.
NHTSA ODI #11354644
103,000 miles · Jun 17, 2020
Visibility/wiper
SPONTANEOUS CRACK DEVELOPED DOWN THE PASSENGER SIDE OF THE WINDSHIELD IN MY 2016 SUBARU OUTBACK WHILE DRIVING. NO OBVIOUS REASON SUCH AS IMPACT WITH STONE OR ROCK WAS INVOLVED- LARGE CRACK JUST SUDDENLY APPEARED. HAVE READ MANY REPORTS OF OTHERS HAVING SAME ISSUE, AND SUBARU HAS HAD AT LEAST 3 CLASS ACTION LAWSUITS FILED AGAINST…
Read full complaint
SPONTANEOUS CRACK DEVELOPED DOWN THE PASSENGER SIDE OF THE WINDSHIELD IN MY 2016 SUBARU OUTBACK WHILE DRIVING. NO OBVIOUS REASON SUCH AS IMPACT WITH STONE OR ROCK WAS INVOLVED- LARGE CRACK JUST SUDDENLY APPEARED. HAVE READ MANY REPORTS OF OTHERS HAVING SAME ISSUE, AND SUBARU HAS HAD AT LEAST 3 CLASS ACTION LAWSUITS FILED AGAINST THEM FOR THIS EXACT ISSUE. *TR
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration