WENT OUT TO MY CAR THIS MORNING AND NOTICED A LINEAR 6 INCH CRACK IN MY WINDSHIELD-IT EXPANDED FROM NEAR THE WIPER ON THE DRIVER SIDE UPWARD AND WITHIN 2 HOURS ANOTHER CRACK BEGAN ABOUT 5 INCHES LATERAL TO THE EVER EXPANDING FIRST CRACK WHICH IS NOW GREATER THAN 12 INCHES LONG. I CALLED DEVOE SUBARU IN NAPLES FLORIDA AND ASKED A…
Read full complaint
WENT OUT TO MY CAR THIS MORNING AND NOTICED A LINEAR 6 INCH CRACK IN MY WINDSHIELD-IT EXPANDED FROM NEAR THE WIPER ON THE DRIVER SIDE UPWARD AND WITHIN 2 HOURS ANOTHER CRACK BEGAN ABOUT 5 INCHES LATERAL TO THE EVER EXPANDING FIRST CRACK WHICH IS NOW GREATER THAN 12 INCHES LONG. I CALLED DEVOE SUBARU IN NAPLES FLORIDA AND ASKED ABOUT WINDSHIELD CRACK AND REPAIR-I HAD BOUGHT THE CAR THERE 3 YEARS AGO. I WAS INFORMED THEY DO NOT REPAIR WINDSHIELDS, NEVER DID THEY MENTION THIS WAS A COMMON PROBLEM WITH THE OUTBACK. I CONTACTED SATELLITE WINDSHIELD REPAIR AND GAVE THEM MY INSURANCE INFO AND HOPEFULLY MY PROGRESSIVE INSURANCE WILL COVER THE WINDSHIELD AND THE EYESIGHT CALIBRATION.I THEN GOOGLED THE ISSUE AND FOUND THAT THIS IS A REAL AND FREQUENT ISSUE WITH THE SUBARU.
NHTSA ODI #11453928
Mileage unknown · Jan 25, 2022
Visibility/wiper
We have replaced about 5 windshields in this vehicle since we have owned it. The cracks form from the bottom of the windshield in the black area where a rock couldn't possibly chip the windshield. Subaru refuses to recognize this vin number as part of their class action law suit that was just settled and has refused to extend …
Read full complaint
We have replaced about 5 windshields in this vehicle since we have owned it. The cracks form from the bottom of the windshield in the black area where a rock couldn't possibly chip the windshield. Subaru refuses to recognize this vin number as part of their class action law suit that was just settled and has refused to extend the warranty on this particular vehicle although they are covering replacement windshields for other 2016 Subaru Outbacks. They clearly recognize that there is a problem but are refusing to admit fault. You do not need to look far to find numerous complaints in forums on the internet with people describing this exact problem.
NHTSA ODI #11448849
Mileage unknown · Dec 29, 2021
Visibility/wiper
On November 15, 2021 my car was in the garage as normal. I started my car and I heard a "pop" I was headed out my driveway is when I notice a crack at the bottom of the windshield that is about 3" high and then curves for about 4".
NHTSA ODI #11445393
Mileage unknown · Oct 20, 2021
Visibility/wiper
Windshield cracks easily. On my 5th windshield, just replaced 2 weeks ago and it’s cracked again. The windshield cracks easily even with minor rock chips. This is the 5th windshield on this car.
NHTSA ODI #11437501
Mileage unknown · Oct 8, 2021
Visibility/wiper
Windshield cracked without any cause
NHTSA ODI #11436058
Mileage unknown · Sep 15, 2021
Visibility/wiper
The windshield cracked without receiving any kind of impact to it. No rock chip, sudden jolt, extreme temperatures or other weather event precipitated the cracking.
NHTSA ODI #11433072
Mileage unknown · Jul 19, 2021
Electrical SystemUnknown Or OtherVisibility/wiper
The adjustment of the passenger side side view mirror has malfunctioned. The mirror can not be adjusted properly for visibility of cars to the side of the vehicle. Only the driver-side window is operable. All other windows fail to open from the driver side control. The passenger window will no longer operate from the passenger s…
Read full complaint
The adjustment of the passenger side side view mirror has malfunctioned. The mirror can not be adjusted properly for visibility of cars to the side of the vehicle. Only the driver-side window is operable. All other windows fail to open from the driver side control. The passenger window will no longer operate from the passenger side either. These windows would have to be broken in order to escape the vehicle in some situations (flooding). My mechanic says that this is a common problem in 2016 Subaru Outbacks. No warning lights were activated. A mirror not able to be adjusted for optimum sighting of other vehicles is surely a safety issue.
NHTSA ODI #11425585
Mileage unknown · Jul 13, 2021
Visibility/wiper
A small rock chip at bottom of the windshield, near the heated wiper park area, caused multiple cracks across the entire windshield. Replacement was required as visibility was impaired
NHTSA ODI #11424554
Mileage unknown · May 19, 2021
Visibility/wiper
Windshield spontaneously developed a crack; there had been no impact to the vehicle or windshield.
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration