NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
22 reportsClear category filterMileage unknown · Aug 18, 2026
Service BrakesVehicle Speed Control
The car accelerates on its own at times. I am not pressing the gas or going down a hill. It is flat road, sometimes even pulling into my driveway. There is also feeling like I am being bumped from the back and moving when I am idle. I am strict about oil changes and have it fully inspected when I take it every 3 months as I am a…
Read full complaint
The car accelerates on its own at times. I am not pressing the gas or going down a hill. It is flat road, sometimes even pulling into my driveway. There is also feeling like I am being bumped from the back and moving when I am idle. I am strict about oil changes and have it fully inspected when I take it every 3 months as I am a single mom and cannot afford for my children and I to be hurt in an accident or be without a car.
NHTSA ODI #11757580
Mileage unknown · Aug 10, 2026
Vehicle Speed ControlCrash
UNKNOWN When pulling into a parking space at the [XXX] diner my 2016 OUTBACK suddenly accelerated while I was ready to shift from drive to park. It was as if I put the gas peddle to the floor. There was a car about 6feet in front of me which I hit. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. …
Read full complaint
UNKNOWN When pulling into a parking space at the [XXX] diner my 2016 OUTBACK suddenly accelerated while I was ready to shift from drive to park. It was as if I put the gas peddle to the floor. There was a car about 6feet in front of me which I hit. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11755851
Mileage unknown · Jun 9, 2026
Electrical SystemSteeringVehicle Speed Control
SUBJECT: Formal Safety Defect Complaint: 2016 Subaru Outback – Manufacturing Nondisclosure of Latent "Day 1" Design Flaw Causing Ignition Key Entrapment, Uncommanded Steering Column Lockout, and Severe Family Safety Risk I am writing to formally report a severe, unaddressed safety defect and a deceptive corporate practice by Sub…
Read full complaint
SUBJECT: Formal Safety Defect Complaint: 2016 Subaru Outback – Manufacturing Nondisclosure of Latent "Day 1" Design Flaw Causing Ignition Key Entrapment, Uncommanded Steering Column Lockout, and Severe Family Safety Risk I am writing to formally report a severe, unaddressed safety defect and a deceptive corporate practice by Subaru of America, Inc. affecting my 2016 Subaru Outback. This vehicle suffers from a "Day 1" latent engineering flaw that causes the physical ignition key to become permanently trapped in the ignition cylinder, triggering an uncommanded, rigid locking of the steering column assembly. Subaru has possessed documented knowledge of this failure for years, cataloging it under Technical Service Bulletin TSB 16-112-18R. Rather than fulfilling its statutory obligation to issue a comprehensive federal safety recall, Subaru deployed a voluntary, time-bound 8-year warranty extension. Subaru conveniently did not notify me of this warranty extension. By doing so, the manufacturer unconscionably ignored this defect, placing its customers at direct peril. They capitalized on asymmetric information to shift both the financial burden and the severe physical safety risks of a known factory flaw onto my family, the moment an arbitrary time threshold expired. My family and I have been at active, continuous risk in this vehicle since the day we purchased it due to an engineering error that was present when the car rolled off the assembly line. The root cause of this failure is a fundamental engineering defect within the Continuously Variable Transmission (CVT) shifter assembly, specifically, the premature degradation of the electrical contacts within the select lever park-range switch.
NHTSA ODI #11742958
Mileage unknown · Jul 10, 2023
Unknown Or OtherVehicle Speed Control
While driving on the highway at about 60mph my 2016 Outback suddenly accelerated much faster. The only way to avoid collision with another car or cars or end up in a ditch was to drive around them. The brake did not work! After a minute or more(?) I eventually was able to stop using the brake.
NHTSA ODI #11531287
35,000 miles · May 9, 2023
Vehicle Speed Control
The contact owns a 2016 Subaru Outback. The contact stated while the was stationary at a traffic light, the vehicle accelerated independently while depressing the brake pedal. The contact stated no warning light was illuminated. The contact stated that the RPM’s was elevated to 5,000. The contact stated that he turned off and re…
Read full complaint
The contact owns a 2016 Subaru Outback. The contact stated while the was stationary at a traffic light, the vehicle accelerated independently while depressing the brake pedal. The contact stated no warning light was illuminated. The contact stated that the RPM’s was elevated to 5,000. The contact stated that he turned off and restarted the vehicle and was able to continue driving to his destination. The contact called the local dealer and made them aware of the failure. The vehicle was not diagnosed or repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 35,000. The consumer stated the vehicle was inspected and didn't find anything wrong with the vehicle.
NHTSA ODI #11521149
Mileage unknown · Apr 11, 2023
EngineVehicle Speed ControlCrash
At low rate of speed, while parking vehicle accelerated without warning and damaged 3 cars . This happened previously with separate family drivers without damage. This is a serious defect and could potentially cause serious injury or death. This was not driver error. the car lurched forward with absolutely no gas pedal involv…
Read full complaint
At low rate of speed, while parking vehicle accelerated without warning and damaged 3 cars . This happened previously with separate family drivers without damage. This is a serious defect and could potentially cause serious injury or death. This was not driver error. the car lurched forward with absolutely no gas pedal involvement. The previous times it happened at a stoplight with enough room in front to hit the brake. Not this time.
NHTSA ODI #11516580
38,000 miles · Apr 11, 2022
Vehicle Speed ControlInjury
The contact owns a 2016 Subaru Outback. The contact stated that while his wife was parking the vehicle, the brake pedal was depressed but the vehicle accelerated forward going down a hill. The vines from the woods prevented the vehicle from going into a lake. The contact’s wife later received medical attention for an injury to h…
Read full complaint
The contact owns a 2016 Subaru Outback. The contact stated that while his wife was parking the vehicle, the brake pedal was depressed but the vehicle accelerated forward going down a hill. The vines from the woods prevented the vehicle from going into a lake. The contact’s wife later received medical attention for an injury to her left leg. A police report was filed. The vehicle was towed to the dealer, where it remained. The vehicle was not deemed totaled by the insurance company. The manufacturer was made aware of the failure and sent an investigator to remove the black box from the vehicle. The manufacturer later informed the contact that, through their investigation findings, the floor mat below the accelerator pedal and the EZ pass mounted on the front windshield caused the failure. The manufacturer provided the contact with a printout of the vehicle manual. The failure mileage was approximately 38,000. The VIN was unavailable.
NHTSA ODI #11460394
75,000 miles · Jan 7, 2021
Service BrakesVehicle Speed ControlCrash
UPON SLOWING DOWN & PULLING INTO A PARKING SPACE, TO PARK MY CAR IN FRONT OF A BUSINESS, MY VEHICLE SPONTANEOUSLY ACCELERATED FORWARD, UP OVER THE SIDEWALK. THE VEHICLE ACCELERATED A 2ND TIME AS I TRIED TO STOP THE VEHICLE WITH THE BRAKES. THE VEHICLE DID NOT STOP UNTIL IT IMPACTED THE WALL OF THE BUILDING.
NHTSA ODI #11387050
Mileage unknown · May 20, 2020
Vehicle Speed Control
TL* THE CONTACT OWNS A 2016 SUBARU OUTBACK. THE CONTACT STATED WHILE DRIVING 70-75 MPH IN THE RAIN, THE VEHICLE INDEPENDENTLY ACCELERATED WITHOUT WARNING. THE CONTACT WAS UNABLE TO REMEMBER WHAT WAS DONE TO SLOW AND STOP THE VEHICLE. THE LOCAL DEALER AND MANUFACTURER WERE NOT CONTACTED. THE FAILURE MILEAGE WAS UNKNOWN.
NHTSA ODI #11325312
1,000 miles · May 16, 2020
EngineVehicle Speed Control
WHILE SITTING STILL AT A RED LIGHT WITH MY FOOT ON THE BRAKE AND THE GEAR IN DRIVE, THE CAR WILL SUDDENLY LURCH FORWARD SEVERAL FEET. IT HAPPENS WITH SUCH FORCE THAT IT FEELS LIKE I WAS REAR-ENDED. THIS HAS HAPPENED OCCASIONALLY SINCE I PURCHASED THE CAR IN JANUARY 2016. ALWAYS WHEN AT A FULL STOP ON FLAT AND SLOPED SURFACES. AT…
Read full complaint
WHILE SITTING STILL AT A RED LIGHT WITH MY FOOT ON THE BRAKE AND THE GEAR IN DRIVE, THE CAR WILL SUDDENLY LURCH FORWARD SEVERAL FEET. IT HAPPENS WITH SUCH FORCE THAT IT FEELS LIKE I WAS REAR-ENDED. THIS HAS HAPPENED OCCASIONALLY SINCE I PURCHASED THE CAR IN JANUARY 2016. ALWAYS WHEN AT A FULL STOP ON FLAT AND SLOPED SURFACES. AT FIRST I THOUGHT IT ONLY HAPPENED WHEN THE AC WAS ON, BUT IT HAS HAPPENED WITH THE AC OFF. *TR
NHTSA ODI #11324748
Official recalls
4Dec 19, 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Nov 24, 2015
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Aug 10, 2015
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration