NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
53 reportsClear category filterMileage unknown · Apr 11, 2023
EngineVehicle Speed ControlCrash
At low rate of speed, while parking vehicle accelerated without warning and damaged 3 cars . This happened previously with separate family drivers without damage. This is a serious defect and could potentially cause serious injury or death. This was not driver error. the car lurched forward with absolutely no gas pedal involv…
Read full complaint
At low rate of speed, while parking vehicle accelerated without warning and damaged 3 cars . This happened previously with separate family drivers without damage. This is a serious defect and could potentially cause serious injury or death. This was not driver error. the car lurched forward with absolutely no gas pedal involvement. The previous times it happened at a stoplight with enough room in front to hit the brake. Not this time.
NHTSA ODI #11516580
Mileage unknown · Feb 20, 2023
EnginePower Train
Subaru dealer diagnosed oil leaks on the valve cover gaskets. I took the car to an independent repair business and the problem was diagnosed as a camshaft carrier oil leak. Upon removing the necessary parts, the company reported to me they found chunks of silicone around the carrier. I first noticed a smell of something burnin…
Read full complaint
Subaru dealer diagnosed oil leaks on the valve cover gaskets. I took the car to an independent repair business and the problem was diagnosed as a camshaft carrier oil leak. Upon removing the necessary parts, the company reported to me they found chunks of silicone around the carrier. I first noticed a smell of something burning after Subaru had done an oil change about 2 months prior. I was also getting the Check Oil lamp about 2 months after the oil change. It was losing oil. That’s when I had Subaru diagnose the problem. The loss of oil could have started a fire. Parts are available for inspection.
NHTSA ODI #11508206
Mileage unknown · Jan 27, 2023
EngineFuel/propulsion SystemUnknown Or OtherCrashInjury
I was in a parking lot at a near-complete stop. I needed to nose the car about 18 inches to move it all the way into the spot. I lightly touched the accelerator to inch the car forward, and it shot forward as if some outside force had stomped on the accelerator. The car jumped the sidewalk and slammed into the wall of the buildi…
Read full complaint
I was in a parking lot at a near-complete stop. I needed to nose the car about 18 inches to move it all the way into the spot. I lightly touched the accelerator to inch the car forward, and it shot forward as if some outside force had stomped on the accelerator. The car jumped the sidewalk and slammed into the wall of the building. The car inner body bent and the car is totaled. The airbags did not inflate. The passenger in the passenger seat sustained a fractured sternum and two broken ribs from going into the seatbelt. The driver sustained a sore neck and dizziness.
NHTSA ODI #11503955
110,000 miles · Dec 30, 2022
Engine
The contact called on behalf of his mother who owns a 2016 Subaru Outback. The contact stated while driving at various speeds, there were abnormal knocking sounds coming from the engine. There was no warning light illuminated. Additionally, the contact stated that he was informed at a State Inspection that the vehicle was includ…
Read full complaint
The contact called on behalf of his mother who owns a 2016 Subaru Outback. The contact stated while driving at various speeds, there were abnormal knocking sounds coming from the engine. There was no warning light illuminated. Additionally, the contact stated that he was informed at a State Inspection that the vehicle was included in Subaru Campaign Numbers: WUJ95 and WTH68. The vehicle was taken to the dealer where it was diagnosed that the engine intake manifold was fractured. The contact stated that he informed the dealer that he would not pay a fee for the maintenance of the vehicle and the dealer informed him that the parts to repair the vehicle under Subaru Campaign Number: WUJ95 were not available. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 110,000.
NHTSA ODI #11499517
Mileage unknown · Sep 21, 2022
Engine
Exhaust manifold cracked completely through, causing exhaust fumes in the interior of the car. There is a recall on this part for 2015/16 outback, but only includes certain manufacture dates, my car is not currently included in the recall. This part is clearly defective as the break occurred suddenly under normal driving conditi…
Read full complaint
Exhaust manifold cracked completely through, causing exhaust fumes in the interior of the car. There is a recall on this part for 2015/16 outback, but only includes certain manufacture dates, my car is not currently included in the recall. This part is clearly defective as the break occurred suddenly under normal driving conditions, pipe is clean, no rust.
NHTSA ODI #11485739
Mileage unknown · May 27, 2022
Engine
The cam tower sealant failed, allowing a leak at less than 70,000 miles driven.
NHTSA ODI #11466469
Mileage unknown · May 1, 2022
Electrical SystemEngineUnknown Or Other
I bought this used 2016 Subaru Outback about a year and a half ago from McCords Vancouver Dealership. I've had the battery dying problem ever since I got it. I have had to call AAA for jump starts. I took the car into my mechanic because the "change warning light" had been on when I turned off the ignition the night before, and …
Read full complaint
I bought this used 2016 Subaru Outback about a year and a half ago from McCords Vancouver Dealership. I've had the battery dying problem ever since I got it. I have had to call AAA for jump starts. I took the car into my mechanic because the "change warning light" had been on when I turned off the ignition the night before, and it was still blinking the next morning when I came out to start the car. He suggested that I go to Costco to get the battery replaced because it was down to only 22% efficient. They declined for several reasons. It wasn't the battery fault, it was the car! I am 92 years old and disabled. I can't get stuck on a freeway with a dead battery. I am still looking for someone to fix it. I bought this car because I assumed that a newer car would be more dependable. Boy was I wrong! I have already spent a lot of money trying to fix it. [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11462941
Mileage unknown · Feb 24, 2022
Engine
NUMBER: WUJ-95 - Exhaust Pipe Front (EPF) Bellows Cracking recall that affects cars produced as below Model Year Carline Affected Production Dates 2015-2016 Legacy 12/16/2013 - 9/30/2015 2015-2016 Outback 12/09/2013 – 9/30/2015 Affects cars outside this date. My 2016 Subaru Outback was built in March of 2016 and the exact same…
Read full complaint
NUMBER: WUJ-95 - Exhaust Pipe Front (EPF) Bellows Cracking recall that affects cars produced as below Model Year Carline Affected Production Dates 2015-2016 Legacy 12/16/2013 - 9/30/2015 2015-2016 Outback 12/09/2013 – 9/30/2015 Affects cars outside this date. My 2016 Subaru Outback was built in March of 2016 and the exact same part broken at the exhaust bellows, requiring a $2600 repair. Instead of a issuing a recall Subaru is offering allowances to the repair. The service advisor stated that he has performed many of the same repair outside the production dates listed on recall WUJ-95 - Exhaust Pipe Front (EPF) Bellows Cracking, The production dates need to be extend to include all cars that have defective exhaust bellows and catalytic convertors. I have images and video of the inspection.
NHTSA ODI #11453839
Mileage unknown · Jan 31, 2022
EngineUnknown Or OtherFire
My car spontaneously burst into flames after I parked it. I had left the car parked and locked in a parking lot next to a rental house and went in to prepare dinner. 20 minutes later my friends arrived at the scene and alerted us to the fact that my car was engulfed in flames. It seems that the fire originated in the engine som…
Read full complaint
My car spontaneously burst into flames after I parked it. I had left the car parked and locked in a parking lot next to a rental house and went in to prepare dinner. 20 minutes later my friends arrived at the scene and alerted us to the fact that my car was engulfed in flames. It seems that the fire originated in the engine somehow, but exactly what started it is unclear. There was no accident or collision, and no foul play. Security cameras in the area couldn't see much, but indicate that the vehicle burst into flames pretty much just after I had left it parked and locked.
NHTSA ODI #11449634
Mileage unknown · Jan 26, 2022
Engine
Issue with the vehicle's exhaust being loud - upon dealership's multi-point inspection, cracked bellows was identified. Issue that was identified and fixed is described in NHTSA ID Number: 10199936, Exhaust Pipe Front (EPF) Bellows Cracking, however the VIN of my vehicle was not included (although it is the same make and model y…
Read full complaint
Issue with the vehicle's exhaust being loud - upon dealership's multi-point inspection, cracked bellows was identified. Issue that was identified and fixed is described in NHTSA ID Number: 10199936, Exhaust Pipe Front (EPF) Bellows Cracking, however the VIN of my vehicle was not included (although it is the same make and model year). Request that this issue be investigated to determine if additional VINs should be included.
NHTSA ODI #11448938
Official recalls
4Dec 19, 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Nov 24, 2015
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Aug 10, 2015
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration